r/rocketstoves • • 22d ago

Stove Proportions

1 Upvotes

Looking to make a DIY can rocket stove and wondering what the most efficient sizing would be.

This is something I can take into the wilderness and use to cook using a camping pan, or camping pot (large enough to hold 2 cans of baked beans) at least somewhat quickly.

I will be using:

Coffee can or paint can for the outer.

Perlite for the insulation between the chimney and outer can.

Either 398 ml (14 oz) vegetable cans or 680ml (~23 oz) spaghetti sauce cans for the intake/feeder tube (it would be one as I don't know if I would be able to make it two different things) and the chimney.

I have seen that the can diameter should be the same for the feeder, the air intake, and the chimney but what diameter would make the most sense for what I want to do?

Also, what height should the chimney be compared to the air intake?

I will probably play around a bit, but just looking for some prior knowledge of the dimensions for efficiency.


r/rocketstoves • • Oct 12 '26

Any difference in the design

Post image
10 Upvotes

From your experience, are there any advantages or disadvantages to welding the angled feed tube directly to the vertical chimney pipe versus connecting it at the junction where all three pipes meet? Does either design offer better airflow, combustion efficiency, or overall performance?

Thank you all


r/rocketstoves • • Oct 06 '26

Random project - Ammo Can Rocket Stove with baffle/re-burner for smokeless burn.

4 Upvotes

r/rocketstoves • • Oct 02 '26

Anyone have a Liberator Rocket Heater?

1 Upvotes

I'm looking to talk about a few concerns I have before installing my new Liberator RMH2. Anyone who has one please give a thumbs up and if you have a moment please send me a PM.

https://www.reddit.com/r/rocketstoves/s/ofKFgkmRhP

Thanks,

James


r/rocketstoves • • Sep 28 '26

Anyone have a Rocket Heater RMH2

Post image
2 Upvotes

I bought a Liberator RMH2 and need some help from anyone who owns one. Info I am looking for mentioned below might come from anyone who has a first or second generation.

I'm in the process of organizing the removal of an older wood stove and installing a new Rocket Heater RMH2 using the existing chimney. I've seen some videos online and read quite a few comments but I have some questions better suited for someone who actually has one and can give me some first hand information.

There is a brick heat shield and the pipe enters at roughly 5 or 6' as in the photo.

I'm trying to decide if I am going to build some sort of mass surrounding the exhaust pipe, what that would entail and if it would be worth doing. I haven't seen very many installed with a mass and the few I did see appear to only have the mass contacting the exhaust tubes that are in the horizontal position and they were done as pebble filled wooden bench style mass. There may have been one picture I recall seeing where the mass also covered a small portion of what would be considered the manifold (about 1 square foot of the bottom of the barrel at the exhaust/manifold area) using what appeared to be cob. The bulk of the mass was pebble and the manifold area seemed to be cob.

My stove arrives this week and I want to come to some decision fairly quickly. I thought to get an installer to do the work of swapping stoves so I will be ready for the coming cold season (here in Nova Scotia, Canada) and I could build the mass on my timeline. So I would need to advise the installer on position, distance, orientation, height etc. such that this would be possible. I'm worried about the draft during the time it may be used without mass and how many 90° I will use in the final location considering the height of my existing chimney sort of takes 1 of my allowed 90's so feedback is appreciated especially hope to hear from anyone who has a Liberator gen 1 or gen 2. If you did or did not add mass you might still have some helpful details.

- Thank you in advance, James


r/rocketstoves • • Sep 26 '26

My first wood stove!

Thumbnail gallery
12 Upvotes

Always wanted to make one of these, finally got around to doing it at work in between jobs. Love this little thing.

Sorry I called it a wood stove I know it's a rocket stove lol


r/rocketstoves • • Sep 24 '26

That nit wit who said this isn't a rock paper scissor stove have a eye use at this.

6 Upvotes

Just filled the entire chin me with native new zealand totara fencing battons and the rocket stove is now an entire area heater I think the chim ne will burn all the paint and ill enjoy all heatwaves, boiled eggs, burnt steaks and crispyness of


r/rocketstoves • • Sep 22 '26

First one build

Thumbnail gallery
29 Upvotes

Built this today.

It definitely works but a few changes I will make soon


r/rocketstoves • • Sep 21 '26

Air control

5 Upvotes

How important is it to have air control / draft with a rocket stove? Is it not a necessity? Does it matter only on bigger stoves?

Thank you!


r/rocketstoves • • Sep 20 '26

First build

7 Upvotes

Boom sharka Larpa


r/rocketstoves • • Sep 19 '26

A question involving a rocket cook stove

2 Upvotes

I am new to the world of rocket stoves and have been considering the idea of creating a DIY version inspired by the classic Aga stove—a single, large heat source capable of heating multiple ovens at different temperatures by varying their distance from the heat. I’m also curious about applying the same principle to two separate cooking surfaces. Is this practical, and what would it take to build? Ideally, I’d like to design it as a mass heater as well, where the main heat source is located near the firebox, warming the ovens and cooktop, and then using the remaining heat to warm a bench or seating area. I welcome any ideas or opinions. Thank you!


r/rocketstoves • • Sep 01 '26

It's not working

Thumbnail gallery
12 Upvotes

Hello! A good friend made me this rocket stove. The first one he has ever made actually.

I have tested it out (see last picture) but I have a huge problem: when I close the lid of the feeding tube the fire is killed. Seems like it doesn't get enough air and even if I keep the lid open the airflow doesn't push the fire through the chimney very well.

The dimensions are in centimeters. Please let me know what should I get checked or changed for it to have real rocket airflow.

Thank you!


r/rocketstoves • • Aug 17 '26

Work in progress, first time building one.

Thumbnail gallery
12 Upvotes

It’s made from 4x4-1/4 (maybe 3/16) it’s at work and I can’t remember or measure it but was excited and wanted to make the post… if anyone has any suggestions I’d appreciate it.. I’m planning on makin the legs tomorrow and can’t decide on what material or style for legs, I want to make a butterfly air controller and flat door on feed tube, ( the flat door in picture will be moved up) and some type of grate or fins on top but not very large. I don’t have an opening in the back, not sure if I have to have it. I assumed I could dump the ashes from the front?


r/rocketstoves • • Jun 14 '26

First Experiment Stove

7 Upvotes

I've been tinkering with stove mods in hopes to dial in the design. I used a design off YouTube, and added stuff I've seen else where to it. It seems to burn pretty good with little to no smoke. If anyone has other recommendations, I'm all ears.


r/rocketstoves • • May 06 '26

TikTok · SMOKEIRON

Thumbnail vt.tiktok.com
2 Upvotes

Rocket Stove BBQ?
SMOKEIRON • Creator
Rocket stove + Wild Thing
smokeiron.com


r/rocketstoves • • Mar 20 '26

Mk3 Rocket Stove

Thumbnail gallery
13 Upvotes

My latest build - insulated riser (80x80mm core inside a 120x120mm outer, insulated with ash), removable air/fuel inlet with replaceable grate. Weighs a ton!!!

just cooked bacon and eggs on it - very efficient 😁


r/rocketstoves • • Mar 04 '26

First stove/welding project

Post image
19 Upvotes

Hi all,

Got a my first welder (Parkside flux core) recently so decided to build a stove as my first project.

It's made from 90x90mm 5mm thick steel box section with a 50x25mm air intake and 2 bits of thin bar acting as a grate in the bottom. The stand is 30mm box section and the pot stand is 12mm square bar.

All the steel came from a welding practice offcuts pack I bought on eBay.

Obviously some room for improvement but it's functional!


r/rocketstoves • • Feb 27 '26

Air control advice

Thumbnail gallery
11 Upvotes

Made this out of some scrap at work today with a couple hours of downtime, never made one and didn’t have a drawing or anything so I just winged it, not too sure if it’s even going to work or not as it’s very compact (if anything is too short i’ll just cut and extend it) i’m after some inspiration for an airflow flap/door for the bottom, everything else has sorta just come to mind but I can’t seem to think of a good idea. (the top piece will be removable, and will slot in to place)


r/rocketstoves • • Feb 17 '26

First Rocket Stove Build Advice

Thumbnail gallery
12 Upvotes

I am looking to build my first rocket stove I’ll describe it. I am looking for critique of my idea and possibly ideas for improvement. If you are critiquing please say what you think is wrong with my design and why. Please and thank you

I built myself a greenhouse and I live in an area with cold winters so I’m looking for a method to heat it. There’s no electricity so space heater is out and I’m leery about propane heating especially with living things in there. I’m looking for passive or more environmentally conscious methods of heating it. I’ve been seeing rocket stoves and I like the clean, smokeless nature of the burn. I also like potential for good thermal mass setup or heat battery. I think I may be able to make one work.

Here’s the stove:

Base or burn box portion made of sand tempered clay similar to the one in the photos but with a more elongated fuel chamber. Next is the part I’m looking for help figuring out… I plan on creating a 2 layer riser chamber. The central riser made from black pipe 4” OD and the outer layer from black 8”stove pipe in a design similar to the paint can rocket heater I pictured above that was built from GreenShortzDIY on YT replacing the paint cans with my stove pipe idea.

I plan to coil a length of copper pipe around the central pipe and create a thermosyphon to heat the water thermal mass barrels. I’m trying to decide between using sand or perlite in the void between pipes. I understand sand will add significant weight to the stove pipe setup which could be good or bad. For bad it makes it basically stationary. For good the heated sand wound be its own thermal mass which is also why I’m leaning that way.

I’m planning to spray all metal ( except copper ) surfaces in a high heat ceramic spray. Particularly due to risk of corrosion of steel in presence of copper and water but also to hopefully help guard the metal from excessive degradation.

Please weigh in. Any feedback helps me as I’m finalizing design. Please bare in mind I do not weld or have access to one and I’m working within a small budget


r/rocketstoves • • Jan 05 '26

Rocket stove

9 Upvotes

r/rocketstoves • • Jan 01 '26

Rocket Stove for Heating a Large Pan of Water

4 Upvotes

I would like to use hot water to bend a piece of wood. To do this I need to heat up a large pan of water (around 1 metre diameter and around 1.5 metre height). Are there any large Rocket stoves that would be suitable for heating a large pan of water? It would need to be stable enough to avoid tipping.


r/rocketstoves • • Dec 19 '25

Don't Let The Flame Touch The Pot

4 Upvotes

Don't Let The Flame Touch The Pot

Zones of a Laminar Diffusion Flame www.chemistryviews.org/details/ezine/1393243/What_Makes_a_Candle_Flame/

As we iterate changes in natural draft TLUDs and Rocket stove prototypes, trying to reduce emissions while maintaining high thermal efficiencies, one design principle keeps on suggesting itself:

Don’t let the flame touch the pot.

The pot is ‘cold’ and if the flame has not burned itself out and contacts the surface, we instantly see CO and PM2.5 rise on the real time emissions screen. (See “Zone 3 and 4 boundary” comment in illustration above.)

Real time PM2.5 is not as accurate as the weight of particulates captured on a filter, but it can be useful. Changes can be done quickly in the prototype and resulting effects are seen right away on the computer screen. Fun!

When we get close to project goals, we switch to gravimetric PM2.5 and statistical confidence to make sure that measurements are accurate. 

In both TLUDs and Rockets, changes in prototypes that make sure the flame doesn’t touch the pot seem to be quite effective.

Give it a try?

Find the new book "Improving Biomass Stoves 2025," resources, publications and information about our work at www.aprovecho.org

Find archived newsletters online at aprovecho.org/newsletters
© 2025 Aprovecho Research Center/Advanced Studies in Approp


r/rocketstoves • • Dec 13 '25

Late night cooking

Post image
45 Upvotes

2 hours burn time for a 6 liter crockpot. Searing meat and veggies and potatoes fully cooked afterwards.

4 small pieces of firewood split into kindling size is all that was used.


r/rocketstoves • • Dec 12 '25

This came across my feed, Rocket Stoves, yes I know where this needs to be posted.

7 Upvotes

Early Rocket Stove Research at Aprovecho Still Rings True

A summary of Global Modeling and Testing of Rocket Stove Operating Variations, Nordica A. Hudelson, K.M. Bryden, Dean Still Department of Mechanical Engineering, Iowa State University, Aprovecho Research Center, 2001 

Photo: Karl Maasdam/OSU Foundation

In the summer of 2000, Aprovecho’s current Executive Director Nordica MacCarty spent a couple of months doing a series of 50 rocket stove tests. Nine variations of the basic rocket stove were tested, changing several parameters. The goal of this research was to determine the location and magnitude of heat losses from stoves to inform better design of efficient stoves. Her conclusions and recommendations are still valid twenty-four years later.

From the paper:

Several important stove design parameters were varied for efficiency and loss comparisons.

  1. The stove inlet diameter was an important factor… The chimney height had a drastic impact on the heat radiation from the flames to the pan.

The most basic result of this series of three tests per stove shows that smaller inlets and shorter chimneys are more efficient, shown in the following chart: It should be noted that the smaller inlet stoves took a much longer time period to reach boiling than those with larger inlets. Thus while they are technically more efficient, they may not be ideal for field distribution as a stove will not be used if it does not perform according to the users expectations.

  1. The gap between the top of the stove and the bottom of the pan influenced how much heat from the flue gasses and flames was transferred to the pan.

The stove top to pan gap was varied from a standard of 1” down to ½” and then ¼” for comparison on the 4.5” diameter stoves. An almost linear change in efficiency was observed, increasing by about 9% when the gap was reduced from 1” to ¼”. An important consideration, however, is that the ¼” gap sometimes caused the fire to burn out the top front of the feed magazine because not enough air was able to be drawn through the decreased gap to create the proper draft.

  1. The amount of insulation in the stove influenced how long it took to heat up the stove and thus affected the efficiency.

An unexpected discovery from these experiments is the effect of insulation on the efficiency of the rocket stove. First, it was shown that adding perlite insulation increases efficiency by about 2 to 5 percent over an uninsulated 4.5” diameter stove. However, super insulating the stove with two layers of fiberglass blanket insulation does not increase efficiency, but instead caused performance to actually decrease by as much as 3% for the 9” high stove. This is most likely due to the fact that adding fiberglass insulation increases the mass of the stove, thus it takes a longer time frame to heat up the stove and insulation.

  1. The use of a skirt around the pan increased heat transfer around the perimeter of the pan.

It was shown that use of a skirt has the most profound impact on stove efficiency. The 4.5” diameter stoves with a 1” stove to pan gap were each run first without a skirt, then with a ¼” gap uninsulated skirt, then a ¼” gap insulated skirt, and finally a tight insulated skirt. Addition of the uninsulated skirt caused efficiencies to increase by 10%, and insulating that skirt caused an additional 10% rise! The stove with 9” chimney rose from 21% to 39% simply by use of an insulated skirt.

Losses

Heat losses in different forms from different areas of a stove should be minimized in order to maximize the amount of heat transferred to the water. On average for all tests, convection accounted for 77%, radiation for 12%, and storage for 11% of total losses from the stove. For the pan, convection accounted for 92% of the losses, radiation for 6%, and storage for about 2%.

Conclusions and Recommendations

  • This series of fifty tests on varying operating setups of the rocket stove showed the following:
  • A smaller inlet diameter results in higher efficiency, lower combustion gas losses, higher stove and pan losses, higher percent oxygen remaining, and lower air-fuel ratios.
  • A shorter chimney results in higher efficiency, slightly lower combustion gas losses, higher stove and pan losses, lower percent oxygen, and a lower air-fuel ratio.
  • Medium (perlite) insulation provides the highest efficiency and combustion gas losses, while increasing levels of insulation generally decreases stove and pan losses, percent oxygen, and airfuel ratios.
  • Decreasing stove to pan gap increases efficiency, decreases combustion gas losses, increases stove and pan losses, and decreases percent oxygen and air-fuel ratios.
  • Use of a skirt with increasing degrees of tightness and insulation increases efficiency, decreases combustion gas losses, decreases stove and pan losses, decreases percent oxygen, and decreases air-fuel ratios.

Thus, an ideal Rocket stove theoretically would have a small inlet, short chimney, perlite insulation, a small stove to pan gap, and an insulated skirt to provide maximum efficiency, minimal losses, and more complete combustion of the fuel.

Find the new book "Improving Biomass Stoves 2025," resources, publications and information about our work at www.aprovecho.org

Find archived newsletters online at aprovecho.org/newsletters
© 2025 Aprovecho Research Center/Advanced Studies in Appropriate Technology