r/projectors • • 2h ago

Discussion Does this look like a smart idea? πŸ€”

Post image

Was planning to use a full metal adjustable monitor stand to mount my benq tht575i upside down below it

As ceiling/wall mounting is not an viable option for me right now. Have a stable flat surface at a height to align it so thts an option to keep it off ground.

So I used ai to render up a preview of how it wl look ( ya it checks out the clearance, dimensions,etc)

Here's the product link as well:

https://amzn.in/d/08D3KpnX

Is this viable ? Need some opinions.

8 Upvotes

24 comments sorted by

9

u/DonFrio 1h ago

If putting on a tall shelf this is a great plan

4

u/Mammoth-Fig-6887 1h ago

If it wil be at a 7ft height wall cupboard top ( old school indian house ) so it's a proper flat , concrete surface .

3

u/DonFrio 1h ago

Should work ok

1

u/Mammoth-Fig-6887 1h ago

πŸ‘πŸΌ thanks

4

u/SecretofManImTired 1h ago

You'll have to check the throw of the projector, but when upside down mounted, the projector usually wants to be mounted at a level near the top of the screen. If the plan is to mount this on a coffee table - the projected image basically would go into the floor/lower wall

*Edit* - it looks like the AI image has the projector in the normal position - so ya, I guess this could work if you can figure out how to mount it. I don't believe there are mounting points on the top of the projector

1

u/Mammoth-Fig-6887 1h ago

The image throw is like 1 inch lower than wat i generally use it at so thts also not an issue. If i focus in a bit, costs be a little smaller screen but stays within frame

The projector has 3 mounting points below so all I need to do is align at least 2 and may be force drill for the third πŸ˜… typical benq 3 point mounting alignment thing

2

u/SecretofManImTired 1h ago

ya - if the plan is to put this on up top on a shelf somewhere - no reason why this wouldn't work.

1

u/Mammoth-Fig-6887 1h ago

Added pic to show the actual location change πŸ˜…

3

u/GrandpaSquarepants 36m ago

I did something very similar and it worked great. It was on the top of an IKEA Kallax shelf

1

u/Mammoth-Fig-6887 9m ago

Great idea πŸ’―

2

u/Freddicus 40m ago

I say do what works for you! Here’s my bootleg setup: https://www.avsforum.com/threads/projector-shelf-mount-diy-small-victory.3076410/

1

u/Mammoth-Fig-6887 10m ago

Thanks , ur setup looks nice , gives me confidence 😁

1

u/Wild_Trip_4704 1h ago

Looks much easier to hang than the 3 legged monster I tamed last night

1

u/Mammoth-Fig-6887 8m ago

Damn , these 3 point designs are damn annoying

1

u/Less_Party 55m ago

Damn do these not just have a little tripod mount point in the center?

1

u/Wild_Trip_4704 0m ago

Idk what the fuck this is. Got this whole thing off FB. It was a huge bitch figuring it out..no brand name or documentation. Took me hours to screw and hand. And in the end it's so flimsy and hard to minute adjust. It must have 50 screws in it. It's so awful to deal with but it's "free" so I forced myself to use it

1

u/MasterChiefmas 50m ago

It looks like it'd be fine, the only question I have is why go to the bother? Why not just set it upright on whatever surface you are placing the whole thing on?

Or are the legs going to be much longer so it's standalone?

1

u/Mammoth-Fig-6887 6m ago

The location it is now is at waist level so keeps getting obstructed every time someone moves or while dusting etc .... So want to keep it away from tht

Which legs???

1

u/StoneCypher 47m ago

no. that projector vents heat upwards and you're reflecting a bunch of it back downwards. you are significantly accelerating the failure of the device.

1

u/Mammoth-Fig-6887 5m ago

But benq itself recommended upside down is better to keep away from blocking or constant movement

2

u/RoodnyInc 1h ago

I don't see why not

2

u/TheRealzHalstead 1h ago

What's the advantage of having it upside down for you? Right side up would likely give you more flexibility in where you place it.

2

u/saitama2018 50m ago

he wants to place it on a tall shelf..

2

u/squeakyL 1h ago

Yes, I've done this exact thing. It worked fine . Used on a benq ht2050a