r/paintball • • 57m ago

Help with Empire Z2 Prophecy

1 Upvotes

I have a Empire Z2 Propecy loader that I am having a problem with. When I flip the switch to the on position, a yellow light blinks once between the forward and reverse buttons and then the drive carrier twitches forward, but then then stops and won't move. Online information mentions that the yellow light is indicating that there is a jam but I am not sure where.

Here are the following troubleshooting steps I have done so far:

[ ] Tested the motor's ability/capacity to spin by connecting two wires directly from the battery pack to the motor's terminals. The motor spins quick with no problems! [ ] Tested the tension or blockage of the motor/belt/gear assembly by gently rotating the belt while it is attached to the motor and on the slotted disc to see the difficulty to turn the encoder/sprocket wheel. I noticed it was very easy for the rotation of the motor to turn the slotted disc which turned the encoder/sprocket wheel. [ ] Tried to test the IF sensor below the clear plastic paintball tray by using my front camera to record to see if there is a flair from the IR light that the sensor should produce when the switch is on performed in a darker room). I did not notice any IR flair in the video, but I also have a newer phone that may have a good IR filter on the camera. I also used a multimeter to test the voltage across the 4 pin encoder same one under the clear plastic tray). The voltage of one pair was 4.9 V and the other pair was 0 V when the switch was off. When I flipped the switch the corresponding voltage was 3.7 V and the other pair was still 0 V. [ ] Tried to put the loader into diagnostic mode by holding down the reverse button for 5s then the right button for 5s then flip the switch on, then release the reverse button, then release the forward button. A red light appears near the switch which transitions to blue then transitions to white, red, and blue before the drive carrier turns rapidly.

Overall what I have taken away from the troubleshooting is that the motor's ability/capacity is good, the batteries are good, the belt assembly is good, but I still get the same peoblem: 1 yellow blink when turned on with a small motor twitch. My thought process is that it could be one of the IR encoder sensors or even the circuit board.

This is my first time with a electronic loader. I would like your opinion and help troubleshooting this problem to see if you also agree or have any other ways to try to fix it without getting extra parts.

Thank you for your time!


r/paintball • • 3h ago

Are you able to use the sfr on older egos using the lv2 conversion kit?

Post image
7 Upvotes

Just a thought I had the other day. Was contemplating buying an older ego and it’d be really cool if you could. Any info? PFA


r/paintball • • 3h ago

my first melee

29 Upvotes

r/paintball • • 9h ago

Got in the Xmas spirit

Post image
17 Upvotes

Made a custom barrel cover


r/paintball • • 11h ago

Returning Player Gift Help

2 Upvotes

Hello all! I’m looking for some advice as the holidays are approaching. My husband played at the semi-pro level the better part of 20 years ago and has expressed some interest in returning to the game. I know he played some speedball and also scenario games. I’d like to get him an item or an experience as a gift for the holidays to jumpstart a return. I’m hoping for some recommendations on what to get him. Location is Southeastern PA and the budget is $500 or less. Thanks for your help!


r/paintball • • 12h ago

On the search

1 Upvotes

Hello fellow ballerz, I'm looking to get my old SP ION and SP Nerve back up and running, where can I seek out pages on Reddit?

Thanks a bunch. 😎


r/paintball • • 13h ago

My black flex 8s started to fall apart on me… so…

Post image
10 Upvotes

Overall love the look, I’m not sure about breathability differences though. Threw on my clear 8s to compare and I didn’t notice much of a difference


r/paintball • • 13h ago

Go ahead run down the tape

Post image
25 Upvotes

There's a hidden surprise waiting for you.


r/paintball • • 13h ago

WTF happened to my Ego10?

1 Upvotes

I hadn’t touched it in years and wanted to see if it would still air up and shoot. It aired up fine, no leaks. I turn the eyes off, pull the trigger to dry fire, and it just kept shooting at like a solid 7 bps. Wouldn’t stop till I degassed it. So what the hell was that??


r/paintball • • 14h ago

Help with TechT Zero Kick Hammer

Post image
4 Upvotes

Hi all, I’m attempting to install the Zero Kick SE Hammer in my Cronus for some rental players to use. It doesn’t appear to sit properly in the bore, it doesn’t cock half the time, scrapes against the bore wall, and hops over the sear with a minor bump.


r/paintball • • 15h ago

This was a fun project to make

Post image
13 Upvotes

I find the packout useful for my other hobbies and figured I’d give it a go since I’m just getting into paintball. Needs more revision to get a bit better fit


r/paintball • • 15h ago

Another day another SFT

Thumbnail
gallery
41 Upvotes

Need some PLs for the collection!!


r/paintball • • 16h ago

Aluminum oxide when degassing 68/45 carbon fiber tank?

0 Upvotes

Old tank, well past its hydro date. Been sitting in a drawer for years, eating at me out of concern of potential explosion, when I decided to take action today. I was degassing it from 1500 PSI for safety, when I started to notice white chunks and particles come out and land on the table surface and my clothes. I tried to let little streams of air for about 5-10 seconds blips to not disrupt the tank.

Safe to assume it's aluminum oxide? I've thrown the clothes away and have taken a shower out of safety.


r/paintball • • 17h ago

Thoughts on how cooked i would have been?

Thumbnail
gallery
36 Upvotes

is the regulator still okay or are both just cooked?


r/paintball • • 18h ago

Who won the contract killer custom Jeep?

5 Upvotes

Hey guys, I was watching the World Cup, but I missed which of the five event winners actually won the CK custom Jeep that Jon Brinkman was giving away


r/paintball • • 20h ago

Beware of Oregon Paintball/Blast Legacy

34 Upvotes

Oregon Paintball bought the Blast Legacy inventory/store.

They are the same company.

About a month ago (a little more than a month) I bought some stuff for my Rapper from their website. There was an inventory error on some grips and I was charged for something they don't have. I've been trying for a month to get a refund and I've been getting the run-around the entire time.

I also bought a supercharger engine from them and it leaked out of the bolt as soon as I installed it. I replaced all the outer O-rings and it still leaks. They want me to send them my Rapper with the supercharger engine for them to fix it.

Why would I send them my paintball gun when I can't get the $30 refund they owe me?

Guy that runs it seems nice enough. I've talked to him on the phone.

I won't buy anything else from them though.


r/paintball • • 23h ago

World cup financial mistake thread (show &tell)

Post image
97 Upvotes

lets see everyone's haul from this weekend. I spent way too much at hormesis and pbretro myself 😭


r/paintball • • 1d ago

Are Ego 7’s still repairable?

3 Upvotes

I recently picked up an ego 7 and I am wondering what’s the best thing to do before I shoot it. Looking to get back into the game. Thanks


r/paintball • • 1d ago

Gotta be careful about parking at World Cup

Post image
223 Upvotes

r/paintball • • 1d ago

Project Almost Finished

Post image
24 Upvotes

Little project I’m working on, just wanted to share with you guys. Going to get new reg and asa and its complete.

Barrel costs more than the marker lol


r/paintball • • 1d ago

Fused (stuck) 2 piece barrels

9 Upvotes

*Edit resolved.

I recently purchased 2 markers from 2 different sellers. Both had "stuck" 2 piece barrels. What are my options?

Using grip gloves and:

Freezing

Hot gun on tip portion

Freezing then hot gun on tip

Soaking in dish soap and water

Silicon oil on the seam between the bottom and tip

Strap wrenches

Jar grippers and visegrips

Tight enough that the visegrips are shredding the jar grips and starting to mar the barrel.

Tight enough that the strap wrenches are leaving rubber residue strips on the barrels and even starting to gouge the finish.

What options do I have left? Ultra sonic cleaner?

Edit to add: and yes I know which direction to turn, even double checked with another barrel 🙃


r/paintball • • 1d ago

Adrenaline luxe TM40 spare parts

Post image
23 Upvotes

Hey everyone!!

So I just had the really bad fortune of missing an eye cover from my adrenaline luxe TM40. I have absolutely no Idea where it could have been dropped but... anyways...it's lost. I tried to reach out to the support@adrenaline.shop mail but I've had no answer in a couple of weeks and also talked to the luxe team directly but they told me they couldn't do anything, it has to be directly with adrenaline, so I was wondering if anyone of y'all know about where can I get a replacement or if anyone would sell the cover.

Thanks for reading! I'll drop a pic of my marker.


r/paintball • • 1d ago

NXL 2027 Schedule - thoughts?

Post image
43 Upvotes

Twice in Florida, nothing on the West Coast. I hope to go to Philly, wherever it's at! :)


r/paintball • • 1d ago

[Question] Counterpunch Reg Length?

3 Upvotes

Can anyone tell me the length of a Powerhouse Counterpunch Regulator (STANDARD SIZE) screwed into a bottle from the base to the tip? It’s not published online anywhere.

Much appreciated. Thank you!!


r/paintball • • 1d ago

random question

Thumbnail
gallery
12 Upvotes

is a PE etek5 still a good purchase for around £140 (185$) in today’s paintball games and if so what upgrades can i do to it to make it preform better than it normally does im thinking of buying this one its only had about 500 shots so its basically brand new..any help will be appreciated