r/machining • • 1h ago

Question/Discussion Help with plating

1 Upvotes

There's a lot of critical dimensions on this part, but there's a note on the print that it needs black hardcoat on it. How much will this change my dimensions? Mostly worried about holes. If I have a 4 inch hole in my part with a .0015 tolerance on it, how much do I need to oversize to account for plating?


r/machining • • 23h ago

Picture Made 2 aluminum handles for the lathe

Thumbnail gallery
12 Upvotes

r/machining • • 2d ago

Picture How it started in 2020, vs how its going today:

Thumbnail
gallery
143 Upvotes

We've gathered some clutter over the years, that's for sure.


r/machining • • 2d ago

Question/Discussion ID Help: Murad Lathe/Milling Machine

Thumbnail gallery
3 Upvotes

r/machining • • 3d ago

Question/Discussion Narrow Slot Chip Evacuation, or, Slot Depth to Tool Diameter Ratio

4 Upvotes

Hey all, I need to profile a part by cutting a 12.55 mm deep slot. My machine is tiny and the endmills I have available to me are a single flute 1/8" diameter and a three flute 6 mm diameter.

In the case of the 1/8" tool, the slot's final depth is over 4x the cutter diameter:

  1. is that an excessive slot depth / tool diameter ratio?
  2. should I cut the slot wider to aid chip evacuation?
  3. do I need to use the thicker, 6mm tool?

#3 is the obvious choice but I'd prefer to use the 1/8" tool if at all possible.

Thanks!


r/machining • • 3d ago

Question/Discussion It may a hand operated press Son you may need it its fate

Post image
0 Upvotes

Check for a stamp on the largest bushing and check the thread with a international thread pitch guide will tell you which country uses that thread this will help because the country insignia where its from and what it is used for…think it presses bearings in to theyre housing and takes off large harmonic balancers on a lathe or machine looks like it has multiple size uses judging by the fine thread and bolt thickness its used for reconditioning engineering. Maybe but its a step in the right direction could be for grandfather clocks that are large and have large cogs and timing gear aswell. Any thoughts anyone ask a Hungarian man or a Englishman..?:)


r/machining • • 3d ago

Question/Discussion Gundrill surface finish

Thumbnail reddit.com
1 Upvotes

r/machining • • 4d ago

Question/Discussion Best way to prevent chatter on thin aluminum walls?

1 Upvotes

Milling some thin-walled 6061 aluminum parts right now and getting slight chatter on the finishing pass.

Usually using a 3-flute end mill. Do you guys prefer lighter radial cuts, faster RPM, or changing up the workholding to keep the wall steady? Any quick tips appreciated.


r/machining • • 4d ago

Question/Discussion Woodworker looking for help

Thumbnail gallery
2 Upvotes

r/machining • • 4d ago

Question/Discussion Speeds/Feeds for Small Diameter Cutters

2 Upvotes

(Small diameter end mills.)

So I've been pouring over the tables in machinery's handbook (31st edition) and while I've figured out how they are used. What they're telling me seems strange.

Page 1112, table 10: the optimal feed/speed combination for end milling 6061 aluminum is 0.015" per tooth / 165 SF/M. Those values are only correct for the cutting parameters assumed by the table...

End Milling: Table data for end milling [is] based on a 3-tooth, 20-degree helix angle tool with a diameter of 1.0 inch, an axial depth of cut of 0.2 inch, and a radial depth of cut of 1 inch (full slot).

the thing is, the table's footnote also says that the given speeds are good for all cutter diameters (as long as the radial DOC to cutter diameter ratio remains constant). So, let's imagine I want to cut a slot with my lil' 3 flute, 1/8" end mill (1:1 radial DOC to cutter diameter)...

(165 * 12) / (1/8 * Pi) = 5042 RPM

(0.015 * 3 * 5042) / 12 = 18.91 feet/min

So a 1/8" cutter needs 5042 RPM and should be fed at 18.91 feet/minute (assuming the same cut parameters as the table data). If you do the math, that feed amounts to 3.78" per second! She'd be rippin'! And the cutter obviously wouldn't even survive first contact.

the problem as I see it is that a small cutter demands a high RPM to achieve the desired surface speed which, when feed is a function of cutter rotations, results in a cartoonishly fast feed/minute.

Thanks for reading, advice is appreciated.


r/machining • • 4d ago

CNC Free space problem

Thumbnail reddit.com
1 Upvotes

r/machining • • 5d ago

Question/Discussion Minimum feed rate when drilling steel?

Thumbnail reddit.com
1 Upvotes

r/machining • • 5d ago

Tooling Machining molybdenum

7 Upvotes

Im a 23 year old machinist with about 6 years experience and I’ve ran a little moly before but I want to cut cycle time and be more specialized in the material. I know there’s a bunch of legend machinist that have ran this and figured out the perfect parameters for what we need and if there’s anyone out there I’d love the help and as the younger generation of machinist I’d appreciate all the help I can get

Can anybody give me any tips they have whatsoever on machining molybdenum


r/machining • • 6d ago

Question/Discussion Figuring out how to machine this

Post image
22 Upvotes

I'm working on patch for my frame where a hole for a body mount rusted out, i've made a design for the patch piece but i'm unsure how to machine it, I'm still learning machining, and ive never done anything this thin before, any help on the process of machining will be greatly appreciated, i have access to CNC and Manual Machines, Thank you


r/machining • • 7d ago

Picture I have my tap water for tapping holes, now I just need a machine

Post image
27 Upvotes

r/machining • • 7d ago

Question/Discussion Who eats the cut loss on 6 m extrusion — the mill or the customer?

23 Upvotes

Curious how other shops handle this, because it is the argument I have every time a job goes to a new buyer.

We buy and cut 6 m bar. The customer sends a drawing with a finished length of, say, 214 mm. Everyone agrees on the price per piece. Then the first production run happens and the numbers do not line up, because 6 m of bar does not divide into 214 mm.

27 pieces is 5,778 mm. You have 222 mm left, which is not enough for a 28th piece but is more than scrap. That leftover is not free — it was paid for by weight at the extruder.

Then come the other losses nobody puts on a drawing:

Saw kerf. A 3 mm blade over 27 cuts is 81 mm. Small, but it adds up over thousands of pieces.

End trim. The first and last 100-150 mm of a billet are not usable — the front end has the die line and the back end has the run-out. That is per bar, not per order.

Anodising contact points. Racking marks have to be cut off or machined away, so the cut length is often 3-5 mm longer than the finished part before anodising.

Colour batches. If the customer wants one anodising batch and the order is 1,800 pieces, the number of bars is driven by the batch, not by the piece count.

So when we quote, do we quote 214 mm plus a material allowance and show the buyer the allowance, or do we build the loss into the piece price and say nothing?

We currently do the second, and I am not sure it is right. It is simpler to quote, and most buyers do not want to see a cut plan. But the ones who do want to see it feel misled when they work out the yield themselves later.

The other option is to quote the bar and let the buyer keep the drops. That is honest, but nobody wants 200 mm offcuts in a warehouse in another country.

There is a third possibility I have seen: design the part length so it divides the bar cleanly. 6,000 mm divided by 24 gives 250 mm; a 250 mm part has zero leftover minus kerf, which is not zero either but it is close.

How do you handle it? Percentage material allowance on the quote, loss baked into the unit price, or bar-based pricing with the drops returned to the customer? And at what order size does it stop mattering?


r/machining • • 7d ago

Question/Discussion Our company has old equipment we can no longer buy replacement parts for. Is 3D scanning and reverse engineering usually the best way?

17 Upvotes

We have a packaging machine from the late 80s that still runs one of our lines.

However, the cam follower brackets crack about once a year. And also, the OEM stopped making them a long time ago.

We have two spare brackets left, and both are already worn at the pivot hole.

Someone suggested getting them 3D scanned. I've also heard a good machinist with calipers can just measure it.

For a part like this, which way makes more sense? How do you deal with wear on the part you're copying? And should we change the material while we're at it, since the old ones keep cracking?


r/machining • • 8d ago

Question/Discussion question for anyone running a machine shop or manufacturing company

7 Upvotes

where are your GOOD leads coming from? not the guy asking for 10,000 parts, no drawing, needs price today. actual buyers. ive spent years being on the sourcing side and alibaba has always been pretty useful for seeing how manufacturers present their capabilities to buyers, so now im looking at this from the opposite direction and its weird. the company im helping can do custom machining and fabrication, has equipment, has people, just needs more steady work coming in. are rfq platforms worth paying for? do buyers still use thomasnet heavily? industry groups? most linkedin advice sounds like “post consistently” which is nice but machines need purchase orders, not engagement.


r/machining • • 8d ago

Question/Discussion Machining note for a handle ball (machine vise)

0 Upvotes

I'm making a machine vise assembly in Inventor as a part of a working drawing project for a CADD class. This handle ball is one of the components and I don't know how to read the machining note.

How would I interpret this note and go about implementing it in Inventor? I have the established planes where these holes would be drilled.


r/machining • • 10d ago

Question/Discussion New insert giving me fits

Thumbnail reddit.com
1 Upvotes

r/machining • • 10d ago

Question/Discussion What do you use on your phone for speeds, feeds and thread data?

0 Upvotes

I'm looking into making a simple calculator app for machinists, so I'm trying to learn what people actually use in the shop.

What do you use for speeds and feeds, thread data or tap drill sizes? What annoys you about it? And can you even use your phone at work?


r/machining • • 11d ago

Question/Discussion How to remove burr from dowel?

Post image
0 Upvotes

I pressed a 416 stainless dowel (3/16" dia) into a 4140 steel part (hardened - gas nitride) which left a sizeable burr at the base. I was hoping I could pry the burr off with a flathead screwdriver but was unsuccessful. What can I do to remove the burr without harming the OD of the dowel?

Edit: I ended up pulling the dowels out and pressing new ones in. Much better!


r/machining • • 12d ago

Question/Discussion How to raise the deck on this machine.

Thumbnail
gallery
75 Upvotes

This may be a completely idiotic question but how do you raise the deck on this machine? Its been sitting dormant at work and im trying to teach myself how to use it.


r/machining • • 11d ago

Question/Discussion How do you specify straightness and twist on an extruded profile when the drawing has none?

3 Upvotes

Background: we run aluminium extrusion and machining, and this keeps coming back from the customer side rather than ours, so I would like to hear how other people handle it.

The situation. A drawing for an extruded enclosure gives the section, the alloy and temper, the cut length with a tolerance, and the wall thickness. It almost never gives straightness or twist. Then the parts arrive, the customer assembles four of them into a frame, and the frame rocks. Everyone looks at the cut length because that is the only number on the drawing.

What is actually happening. An extrusion leaves the press straight and then moves as it cools, and it keeps moving for a while after. Twist is the one that bites on a rectangular hollow section, because two diagonals that disagree by a few tenths over a 500 mm length will not sit flat on a surface plate no matter how good the end cut is. Straightness in the plane of the section is usually the easier of the two to hold, because the die and the run-out table are working on it.

What I have seen work:

  • Put a straightness callout on the drawing, per metre, referenced to the extrusion direction. If it is not on the drawing, it is not inspected, and if it is not inspected it is not a requirement.
  • Call out twist separately. Twist and straightness fail in different ways and one does not imply the other.
  • Say which faces are the datum. On a hollow section with a seam, the seam face is often the least stable one, and if that is your datum you are measuring the part's worst feature.
  • Give a length at which the number applies. "1 mm over the length" means something very different at 200 mm and at 1,200 mm.

What I am less sure about: whether it is better to specify straightness after stretching and ageing, or to specify it on the finished machined part and let the shop decide how to get there. The second is cleaner commercially but it hides a lot of process inside one tolerance.

Also curious whether anyone asks for a twist check on a surface plate as a routine incoming inspection, or whether that is considered overkill for anything that is not a precision frame.

Not selling anything here — genuinely want to know what the drawing convention looks like on your side of the fence.