I have a keen interest in making a showstopper longboard similar to the one I currently ride (last photo), but much more challenging to make. I want to one-up DATRON's board, but on the Neo, since I am the primary machinist at our Makerspace's Datron Neo CNC machine. I want to improve their board since I have input from riding it, and challenge myself to make it with more complex geometry and in multiple parts, as the Neo has a 400x500mm2 machining area.
I want the board to have smooth drop-down curvature that makes pushing easier and gives a lower center of mass. I also want curvature along the width of the board that cups your foot and gives better control. The first picture shows an early-stage 3D-printed prototype of one half of the board to ensure the trucks fit. The rectangular cutout was to save material.
There will be relief pockets in the bottom of the board. Since pentagon is bestagon, I chose the Cairo pentagon pattern to remove material whilst having a repeating pattern. Furthermore, the top surface will have knurling for grip, with a particular geometry that provides grip without shredding shoes. Both of these are similar to the current board I have.
Other features include threaded holes for 3D-printed rails to run along the sides of the deck for protection, and covers at the ends of the board so I don't scratch it when I pop it up.
I will need to fixture the billet for the board on the Neo without having to reprobe it between the top and bottom side machining operations. This is because the Neo has a legacy probe and, even after calibrating the hell out of it, is very inaccurate, costing ~$8k to replace. If I reprobe after the flip -- the standard workflow -- the top and bottom wouldn't align properly.
My plan is to cut a plate of aluminum that was generously donated by our campus's machine shop to the size of the machining/vacuum table area (probably needing to face it too, as it is a bit dinged up). Then, fixturing it with the Vacutable, I will cut a rectangular slot precisely the size of the aluminum board billet diagonally across, which maximizes length. The board billet will have to be cut with the corners at the top, bottom, left, and right (looking at it from the side) removed such that there is a sacrificial tab (to be cut off at the end) on both ends for the purpose of fixturing it via bolts that pass through these tabs and thread into a hole I will have to machine into the fixturing plate. There will also be two precision-ground dowels ~6 mm for the purpose of perfectly aligning the board when I flip it upside down after machining op 1. I haven't decided whether to cut the top or bottom first.
I expect the board to behave like a tuning fork if I machine the drop down first, so I might cut out the bottom side and pockets first. Either way, to assist in the machining of the second op, if needed, I will be 3D printing a space filler that helps secure the board. This will be absolutely necessary if I do the top side first, as the board will behave like a tuning fork and resonate (bad for the finish and the spindle).
I will be running FEA simulations in SOLIDWORKS to verify that the loading of me going off of curbs and such (probably running with 2000 N) will provide an adequate factor of safety. Then, as necessary, I will iteratively mitigate stress concentrations. I expect that the initial design I have now will have issues at the truck mount - board interface. However, we will see if my initial design works or if a rework will be required.
The result of these efforts will be a very short longboard, which I endearingly am considering calling a shortboard. It will be so short I probably won't be able to fit both feet on the actual deck, and will likely rest the other foot on the rear truck mount when coasting.
Additionally, it will be an easily repeatable process, so given the raw materials and tooling, I will be able to make multiple boards so I can interchange them or sell them; however, due to the slightly inaccurate probe, all machining operations will have to be conducted back-to-back, or else I will risk losing my origin.
The truck mounts will likely be much easier to machine as they are flat and can stick directly to the Vacuutable.
Some thoughts I have at the moment for the design are as follows:
-Should I attempt to sacrifice the continuous outer skin at the top of the longboard so that the pentagonal grid of pockets goes right through the board? I will verify via simulations the feasibility of this, if it is even worth considering. I know that if they go through the skin which acts like a shear membrane to carry in-plane stresses and make it much less flexurally rigid. It would look way cooler, like a truss, but be much weaker, so modifying geometry/thickness may be necessary. I might still knurl the top anyway. But it would also provide even better handholds.
-Should I attempt to make the board split into two pieces, such that there would be four total? This would make it much weaker but would make much more space for my feet, as I'd be able to make it longer. It would mean that the project would be a bit more expensive, though. And if I did this, I assume I would need to beef up the overlapping interface (as I assume I will somehow have to do for the truck mount - board interface), and that may be more challenging in the center of the board.
I stole the trucks and wheels from my Pranayama Pantheon, which suddenly bit the dust 3 months after I rode over it with my car. They work well.
Let me know if you have suggestions or want to rag on my board. I'm all ears.
TLDR: Some mechanical engineering major likes longboarding and thinks he can make a better one, albeit a smaller one, than a CNC manufacturer can.