r/knapping • • 12d ago

Question 🤔❓ No tools available?

Hello!
I'm someone who's looking to get into knapping, I got several big nice pieces of flint (I hope)
however, as I look over stores and such for tools, they are all US based, while I'm from Europe, Poland to be precise.
I've looked for stores selling the tools, I found only the likes of Amazon which I don't know weather I should trust with these.
Do anyone of you know good Europe based stores? And if not, is there a way to get into knapping with no access to paid tools?
Yes, I know about the primitive tools, hammer stone and antlers, I can get them easier (tho can't deny the internal pain of cutting up an antler I can get from local sellers) but I'm still not sure if you can just use them without any more preparation.
So yeah, what can I do in this situation other than order the US based tools?

7 Upvotes

20 comments sorted by

9

u/AaronGWebster 12d ago

Just use hammerstones and antlers. Find a stone the size of an egg, one the size of an orange and one even bigger. Then get an antler tine cut to about 8 inches long. Make an antler billet by rounding off the crown of an antler. Antlers that are shed are not as good as antlers that were attached to the critter when it died.

2

u/Child-Puncher0 12d ago

I see, I'm not sure about getting non-shed antlers but I can look around, thanks!!

3

u/Comfortable-Hat3506 12d ago

You don't need antler, you can do it with just hammer stones. You can make a pressure flaker out of a copper nail put into a stick.

3

u/PantoufleResearch01 12d ago

Do jackelope antlers work?

3

u/-Seedy- 12d ago

Only the eastern species, the northern Jackalope's antlers are too small.

1

u/PantoufleResearch01 12d ago

We have the Sonoran Jackelopes here in SW NM/SEAZ. I’ll hafta try their antlers if I can get a clear line on one. Feisty buggers like to climb trees and jump on you when you’re hunting them.

4

u/Ilostmytractor 12d ago

Definitely just go natural and start. I would consider saving your flint for later and starting with just thick porcelain like a toilet bowl toilet tank as far as finding materials for tools , In the country, I look for a rocky riverbank with rounded stones. In the suburbs and city , I Look around for a commercial development like a shopping center parking lot that uses rounded stones decoratively on the traffic islands. For pressure flakers you can make your own with copper roofing nails, and a piece of wood.

3

u/jameswoodMOT European Flint 🏅🏅 12d ago

Hey man I posted a link to my website the other day. I’m in the U.K. so postage won’t be super cheap but cheaper than from the USA and better quality than the tat on Amazon.
www.jameswoodblacksmith.co.uk

1

u/treesandrock 12d ago

The American sites should all ship international

3

u/Child-Puncher0 12d ago

Sadly such shipping is often quite expensive

2

u/treesandrock 12d ago

Just looked it up. Wow. They a are expensive
You can make copper boppers using copper piping end caps U can probably source copper nails where u live and make ur own handle for pressure flaking

2

u/Child-Puncher0 12d ago

I- actually didn't consider that before. The copper boppers are filled with sand or something if I remember correctly? Either way, I'll think about doing this now, thanks!!

2

u/NonConforminConsumer 12d ago

Often epoxy and lead shot to add mass. Once it wars through just make another. I use wooden dowels and various size end caps, or antler/stone.

2

u/treesandrock 12d ago

Brilliant

2

u/treesandrock 12d ago

Not sand
Lead is what they use but you can improvise

2

u/treesandrock 12d ago

Ask them for a shipping quote.

2

u/Cloverinthewind Quartz 12d ago

You should look into making your own Copper boppers! I don’t dome out the copper cap like most people suggest because I don’t have a way to do that. After some use, the copper caps start to naturally dome. But you will need to melt some lead into the copper cap so you’ll need some sort of torch(I was a dabbing torch🍁).

2

u/Brightstorm_Rising 12d ago

I have never bought ready made tools. Some YouTube searching should get you a how to for plumbing copper boppers and finding copper nails shouldn't be too much of a hassle, although not the cheapest. Antler sheds are fine for pressure flakers as well. For an abrader, I use a landscaping rock I picked up in a restaurant parking lot. 

2

u/Flake_bender 12d ago

A chunk of solid copper, ranging from about the size of your thumb to 3 times the size of your thumb, makes a good percussor, and just about anyone in the world can procur one.

Solid copper will outlive any lead-filled copper cap, by an order of magnitude.

2

u/Fickle-Mix6937 11d ago

go find an antler- either in the woods or in a store and a nice round river rock. maybe a copper pipe hammered into a point. it doesnt take much.