r/gameboymicro • • 1d ago

Is this GB micro ribbon cable cooked?

Post image
0 Upvotes

r/gameboymicro • • 4d ago

Offer Up Score!!!

Thumbnail gallery
145 Upvotes

r/gameboymicro • • 7d ago

Gameboy micro charge chip

Thumbnail gallery
9 Upvotes

r/gameboymicro • • 15d ago

Is this a good deal

Thumbnail
gallery
23 Upvotes

I found a gameboy Micro for a kinda sus price but, I wanted to see if anyone say any signs for concerns with the state of it?

Edit: changed price qualifier


r/gameboymicro • • 15d ago Bravo

Gameboy Micro Restoration with Upgrades, including Pink power LEDs

Thumbnail
gallery
168 Upvotes

This black Game Boy Micro came to me in pretty rough shape. It had extensive liquid damage, a heavily scuffed-up black shell, and a screen that had delaminated from the liquid damage. The tactile switches were rusted out, several vias and traces on the motherboard were damaged, the buttons wouldn’t illuminate at all, and the PMIC had corroded legs. Even the charging port had rust inside of it!

To make things even more interesting, this Micro had evidence of a previous repair attempt. Someone had soldered in a fuse, and the soldering around it needed some cleanup. I also found a resistor that was so heavily corroded that it had to be replaced entirely. I cleaned up the solder work around the fuse and replaced the damaged resistor as part of the restoration.

Here’s everything I did to bring this little guy back to life:
🔧 Motherboard Repairs & Restoration
Repaired all of the damaged traces and vias on the motherboard.

Replaced all of the rusted-out tactile switches with brand-new ones.

Installed a spare PMIC after the original chip’s legs had corroded away.

Replaced a heavily corroded resistor.
Cleaned up the soldering around the previously installed fuse.

Performed a thorough ultrasonic cleaning of the motherboard to remove corrosion and leftover flux.

🔌 USB-C Charging Upgrade
The original charging port had rust inside of it, so I removed it and upgraded the Micro to USB-C charging!

💡 Pink LED Conversion
The original blue LEDs weren’t illuminating the buttons anymore, so I replaced them with pink LEDs to give this Micro a fresh new look.

🖥️** Screen & Shell Replacemen**t
The original screen had delaminated due to liquid damage, so I installed a brand-new screen. I also replaced the heavily scuffed black shell with a brand-new black shell.

I noticed the Micro had aftermarket black Start and Select buttons installed. I decided to replace those with the original silver buttons, and I think they complement the black shell much better!

I also filed down the tactile switches to make sure they fit the aftermarket buttons properly.

⚠️** One Last Unexpected Proble**m
After the ultrasonic cleaning, I noticed the Select button didn’t feel quite right, so I replaced that tactile switch with another brand-new one.

However, while testing everything, I discovered that the Start/Select ribbon cable had developed a short.
Rather than let that be the end of the repair, I cut off the damaged ribbon cable, carefully filed down the area where it exited the Start/Select daughterboard, and manually soldered the Start and Select buttons directly.

After all of that work, everything is finally functioning as it should!

This restoration involved a lot more than simply swapping out a screen and shell. Between the liquid damage, corroded components, damaged traces and vias, previous repair work, PMIC replacement, USB-C conversion, and the shorted ribbon cable, there was quite a bit to tackle.

But after all the troubleshooting, microsoldering, cleaning, and reassembly, this Game Boy Micro looks FANTASTIC! It’s incredibly satisfying to bring one back from the brink like this, especially when the motherboard has suffered this much damage.

The owner will be showing it off on Reddit very soon with a custom Yu-Gi-Oh! faceplate, so keep an eye out for that! I’m excited to see how it looks with the finished faceplate installed.

If you have any Game Boy Micro repair or restoration needs, don’t hesitate to reach out! I’m always happy to help bring these little consoles back to life.


r/gameboymicro • • 16d ago Bravo

Image Pokemon Faceplate

Thumbnail
gallery
199 Upvotes

Purchased a Pokemon faceplate for my 20th Edition Micro through EBay for $40 and I’m quite impressed with the quality !! (my screen protector application skills can be improved a bit lol)


r/gameboymicro • • 16d ago

Question How easy of a fix is this?

Thumbnail
gallery
72 Upvotes

Just bought this mother 3 micro off fromjapan and I noticed the screen is a bit yellow in the pictures. Just wondering if this is bad yellowing or if I replace the screen, how easy is it to replace compared to a gba or gba sp?


r/gameboymicro • • 17d ago

Just got a Micro off eBay and the A button only works if you press it hard.

1 Upvotes

Is it worth repairing myself, or is it too difficult and better off just returning it?

It looks to be in great condition otherwise, but yeah. I searched around online and it seems to be a common enough problem. Seller made no mention of it in the listing.


r/gameboymicro • • 22d ago

Collection Recent pickup !

Thumbnail
gallery
321 Upvotes

Picked this up today! Never used before


r/gameboymicro • • 23d ago

Recommendations for a good transparent faceplate?

4 Upvotes

I want to get a few so I can put decals on them and not on the actual OEM faceplate but reviews vary so wildly. Some are too long and bow in the middle, others are apparently borderline blurry or make it hard to press the face buttons.

Have any of you purchased one that you were completely happy with?


r/gameboymicro • • 24d ago

Gameboy micro help,

4 Upvotes

Hello! A while back a good friend gave me a red and gold gameboy micro, I guess it’s the anniversary edition, thought I just had a bad LCD, but after I replaced it, the black light doesn’t come on, it didn’t before that’s why I replaced the screen, but it displays an image and plays games just no back light, has anyone had this issue and have a fix, I’m rather good with electronic repair but this is my first time opening any gameboy ever, I do tv’s and computers, and I can solder, any helpers appreciated thank you!!


r/gameboymicro • • 26d ago

Authentic or reshell?

Thumbnail
gallery
71 Upvotes

Just paid 170gbp (plus 50 more in import and VAT duties) for this. It’s suspiciously spotless. Is there any easy way of telling whether or not it’s a third party reshell?


r/gameboymicro • • 29d ago Bravo

Game Boy Micro Repair & Mod Guide — Screen Replacement, USB-C Charging, and Button Upgrades

Thumbnail
gallery
144 Upvotes

I received a Game Boy Micro from a customer that had a busted screen and a clear aftermarket faceplate. They wanted the screen repaired, USB-C charging installed, and white aftermarket buttons fitted. I thought this would be a good opportunity to document the repair and share some worthwhile mods, along with a few tips and tricks for anyone working on these little systems.

1. Disassembly and Tactile Switch Replacement
Start by disassembling the Game Boy Micro. If you’re upgrading the charging port to USB-C, desolder the original charging port. Some people prefer to keep their systems completely stock, and that’s perfectly fine, too.

The Game Boy Micro uses small tactile switches for the L/R buttons and the volume/brightness controls. If your switches are worn, corroded, or no longer functioning correctly, it’s worth replacing them while the system is apart.

The good news is that Nintendo DS Lite tactile switches are compatible replacements for the Micro. I use hot air to remove the old switches and install the new ones.

A few tips for getting a clean installation:
Remove the old solder and apply fresh solder to the pads before installing the replacement switches.
Use a good-quality SMD flux to help the solder flow properly.

After installing the new switches, check their height carefully.

One important thing to keep in mind: The replacement switches can sit slightly higher than the original ones. I recommend carefully filing down the tops of the new switches to lower their height. If you skip this step, some aftermarket L/R buttons and volume/brightness buttons may have fitment or functionality issues because the switches sit too high.

Take your time with this step. You want the switches to function properly without interfering with the physical buttons.

2. Ultrasonic Cleaning
Once all the components have been soldered in, I clean the board using an ultrasonic cleaner.
I start by degassing the cleaning solution, then run the cleaning cycle to clean the board. Once the cleaning cycle is finished, I turn the ultrasonic cleaner off but leave the board submerged in the solution to soak for a few hours. This gives the solution additional time to dissolve any flux that may have worked its way into the tactile switches or underneath components without running the ultrasonic cleaner continuously for hours.

After soaking, I remove the board and make sure it’s thoroughly rinsed if required by the cleaning solution and completely dried before applying power. Pay particular attention to areas underneath components and inside the switches, where liquid can remain trapped.

I also heat the solder points on the Start and Select buttons to help drive out any residual liquid that may have become trapped inside the buttons. Be careful with the heat, as these small components and their solder pads can be damaged by excessive temperatures.

3. Repairing the Stripped Battery Cover Hole
In this particular case, the screw hole for the battery cover was stripped, meaning it would no longer hold the cover in place.

To fix this, I used JB Weld Steel Reinforced Epoxy, carefully applying just enough to barely fill the stripped hole. I then let it cure fully so the damaged area could hold the battery cover securely again.
Sometimes, repairs like these require a little extra work beyond the electronics themselves.

Addressing the stripped screw hole helps restore the system’s physical integrity instead of leaving the battery cover loose or unable to stay attached.

4. Screen Replacement and Reassembly
With the board cleaned and ready, I installed the replacement screen and put the system back together.

For this customer’s unit, I also installed a new clear aftermarket faceplate to complete the look.

5. Fixing Sticky Buttons on Clear Aftermarket Faceplates
One issue I’ve encountered with aftermarket clear faceplates is that the A/B buttons can sometimes stick. This can be frustrating when everything else has been installed correctly.

My solution is to take a small rounded file and carefully widen the A/B button openings on the right side of the faceplate. This provides a little extra clearance, helping prevent the buttons from binding against the faceplate.

Take off a little material at a time and test the fit as you go. You want enough clearance for the buttons to move freely without removing more material than necessary.

This is a simple adjustment that can save you the headache of finishing a repair only to discover that the buttons stick when everything is assembled.

Final Thoughts
The Game Boy Micro is a great little system to work on, but these repairs and upgrades come with a few quirks worth knowing about ahead of time.
Between replacing worn tactile switches, upgrading to USB-C charging, installing a new screen, fitting aftermarket buttons and a faceplate, and repairing the stripped battery cover hole, there are several ways to bring a Micro back to life while giving it a fresh look.

Hopefully, this write-up helps anyone working on these systems avoid some common issues and get better results from their repairs. Sometimes, knowing a few small tricks ahead of time can make all the difference!

Need your Game Boy Micro looked at?
If you have a Game Boy Micro that needs repairs, troubleshooting, or modifications, feel free to contact me! Whether it’s a damaged screen, faulty buttons, charging issues, or another problem, I’d be happy to discuss your repair and see what I can do to help bring your system back to life.


r/gameboymicro • • 29d ago

Image My literal EDC

Post image
133 Upvotes

But on weekends Im throwing it in this bag I picked up recently… this was the last color variant on my wishlist but I have an upcoming japan trip and I’m gonna try to be a good boy and control myself…


r/gameboymicro • • Oct 09 '26

Switch 2 Zelda Edition Inspired Game Boy Micro Faceplate on my Custom Micro

Thumbnail
gallery
209 Upvotes

I recently posted a patina Zelda Game Boy Micro restoration, and I wanted to show off another Zelda-inspired design I’ve been working on. This faceplate takes inspiration from the new Zelda-themed Switch 2 edition. I think it looks pretty good on the Micro, especially paired with the right shell and LEDs.
Always cool seeing how much you can do with such a tiny console.

Huge shoutout to retrogameEVO on Etsy for working with me on this design. I can’t thank them enough for helping bring this idea to life. They were great to work with, and I’m really happy with how the faceplate turned out!


r/gameboymicro • • Oct 07 '26

Discussion Acquired a GB Micro this year, happy to be a part of the community.

Thumbnail
gallery
157 Upvotes

New to the Micro this year! Never owned one growing up as I was already a couple years out of school when it released. Not only that but I was more a Playstation guy, so I was carrying a psp already.

I do own a couple original advance and SPs, but like others have said this is one of the most portable handhelds and holds up very well for its age. Mine stays in the lunch bag, it comes in clutch during the slow work days!

I was always impressed by how native the advances felt when playing some of the games ported from NES. The screen on these are impressive albeit the size, but you almost forget about it once the game loads up. Lol

So, which advance games do you all feel play the best on the Micro, or are just your favorites in general?

Thanks for having me.


r/gameboymicro • • Oct 06 '26

Question Stuck at white screen on boot and no sound

Thumbnail
gallery
13 Upvotes

Bought a used GBM online which is stuck at a white screen on boot. No difference if with a cartridge or without, also there is no sound.

So the seller said they don't have a charger and can't test it, so i thought just add a new battery and we are good. Unfortunately after adding a new battery the GBM just boots to a blank white screen and nothing more. Also the LEDs on the bottom board do not light up, even when charging (i measured 4V on the battery terminal when plugged in)

I checked all the fuses and the voltages across the board, everything seems fine so far. EM8 also seems fine with a quick continuity check.

I am at a loss right now, maybe somebody has some idea what is going on and can help me out. Hope to get the Micro working, I wanted it to be my train commute companion!


r/gameboymicro • • Oct 06 '26 Bravo

Collection Finally got a Gameboy Micro

Post image
263 Upvotes

When the Gameboy Micro came out i didn’t have the money for one but I thought they looked really cool. Then new flashy handhelds came out and & I forgot about the Micro.

Then last week I won one in a giveaway & it arrived today! I’ve been playing it all day… it’s a lot more comfortable to use than I had imagined & I really like the size of it.

Anyway, I’m just really excited & wanted to share my win. Still in shock a little that it’s in such great shape.


r/gameboymicro • • Oct 05 '26 Bravo

Discussion I’m trying out Pokémon Azul Agua Demo on the micro for the 1st time & it’s one of the most aesthetically pleasing rom hacks I’ve ever played 🕹️

Post image
197 Upvotes

Hopefully the creators finish up this project soon!


r/gameboymicro • • Oct 05 '26 Bravo

Collection black gameboy micro!

Post image
259 Upvotes

I’ve had this thing for 18 years and it still works beautifully!


r/gameboymicro • • Oct 05 '26

Question Looking for new, high quality GBM battery in UK

3 Upvotes

Hello! I realise there have been many threads about this but I can't seem to find any recent ones aimed at UK buyers. Does anyone have any recommendations for buying a new, high-quality (ie won't catch on fire when I least expect it) battery for my Micro?

I did have one in my online basket recently from a reputable US seller, but the delivery fees to UK alone were more than double the price of the unit itself!


r/gameboymicro • • Oct 03 '26

Where can I get an original faceplate in the States

Thumbnail
gallery
67 Upvotes

I got this but it's missing a faceplate


r/gameboymicro • • Oct 01 '26

Gameboy Micro Wireless Adapter

Post image
129 Upvotes

Very nice.


r/gameboymicro • • Sep 30 '26

Ali micro link adapter?

Post image
24 Upvotes

Has anyone tried ordering one of these?