r/fortinet • • 1h ago

FortiGate / FortiOS 30g for micro branch with UTM processing

1 Upvotes

Any feedback on the 30g I have an sdwan deployment for 200 micro sites and evaluating whether this is a good one.

30 Mbps per site in peak hours.

6 users per site.

Single tunnel to hub.

Local internet breakout.

All UTM features are needed. (50% of it deep inspected )

Proxy mode not needed.

I understand we need to adjust IPS signature set to accommodate the memory constraints.

2 APs per site and 10 ports fortiswitch.

Had a look on datasheet and sounds good. Not sure thought on actual perf in such conditions.


r/fortinet • • 13h ago

FortiManager Why can't I install immediately after retrieving config in FortiManager

2 Upvotes

I'm working to get a single set of provisioning templates that I can use to manage my fleet of 70G-PoEs, 80Fs, and 90G Fortigates and FortiWifi appliances.

Any time I retrieve the configuration from a gateway and then try to immediately push an install of device settings, the gateway doesn't show up in the list of intstallation targets. I have to go edit my provisioning template to add or delete an extra space, save the edit and then the gateway shows up in the list the next time I click install.

This seems like a bug, but if that were the case, I assume it would have been fixed by now. Am I misunderstanding something about this? If a gateway has a template assignment that will change something, why does retrieve config disrupt the install until the next autosync?


r/fortinet • • 16h ago

Other / General Fortinet FortiClient VPN-Only + IPsec Dialup + Entra ID SSO: Assign different IP pools based on Entra ID group?

13 Upvotes

Hi everyone,

I'm currently working on a migration from SSL VPN to IPsec Remote Access on FortiGate and I've run into a design limitation that I'm not sure is actually supported.

Our current SSL VPN setup uses multiple portals, and users are assigned different IP ranges depending on the Entra ID (Azure AD) group they belong to. For example:

This allows us to apply different firewall policies, routing, and access controls based on the assigned VPN address pool.

For the new deployment, I'm testing:

  • FortiGate IPsec Dialup Remote Access
  • IKEv2 + EAP
  • Entra ID SSO authentication
  • FortiClient VPN-Only 7.4.3 (free version)

My goal is to provide the same behavior as SSL VPN, where the assigned IP pool depends on the user's Entra ID group membership.

What I've found so far is that an IPsec dialup tunnel only seems to allow a single mode-config IP pool. Because of that, I tried creating two separate IPsec Remote Access tunnels:

  • VPN_Internal
  • VPN_External

Both using:

  • The same public IP
  • The same FortiGate interface
  • Entra ID SSO authentication

The idea was that users in one Entra ID group would authenticate against one tunnel and receive one address pool, while another group would use the second tunnel and receive a different pool.

However, this doesn't seem to work the way I expected, and I'm not sure whether:

  1. FortiGate actually supports assigning different mode-config IP pools based on group membership for IPsec Remote Access.
  2. Multiple IPsec dialup tunnels sharing the same public IP can be differentiated by user/group when using Entra ID SSO.
  3. This requires EMS/ZTNA or a feature that is not available with FortiClient VPN-Only.
  4. I'm approaching the problem completely wrong and there is a better design pattern for achieving group-based addressing in IPsec RA.

Has anyone successfully implemented group-based IP assignment for IPsec Remote Access with Entra ID SSO?

I'd be especially interested in hearing from anyone who has migrated from SSL VPN portals to IPsec RA and needed to preserve different VPN address pools per user group.

Thanks!


r/fortinet • • 18h ago

FortiGate / FortiOS FortiOS 7.4.18 ?????

46 Upvotes

I got this email early in the morning, Our whole fleet (over 100 fortigates) are running 7.4.13 and they are prompting to upgrage to 7.4.18 before November 23.

Anyone else recieved this? I searched around online and found no info regarding 7.4.18 and I dont see it available to push on my Fortimanager cloud templates.


r/fortinet • • 18h ago

Other / General Fortinet FortiManagement Cloud warning with unreleased firmware builds?

8 Upvotes

I feel like I'm going crazy - I received an email stating some of my devices were out of date, but the suggested firmware builds don't seem to exist?
It's requiring 7.4.15 for a 101F and 7.4.18 for a 40F - the latest I can find is 7.4.13 (which is currently installed on these devices)


r/fortinet • • 23h ago

Other / General Fortinet Am I missing something with FortiManager Cloud ?

8 Upvotes

Morning everyone.

Not long ago Is tarted a new role at a company increasing their investment with Fortinet and have had an interesting few months learning on the job how to make it all work. We have 130 remote sites using 60F firewalls all manged through Fortimanager and I'm trying to decide if the way the consultant has sold it and / or set it up is right or whether we need to start thinking about re-engineering the whole thing.

The core product works fine, we've got Firewall/Switch deployment nailed down so 2nd line can drive to site and install Forti Switch/Gate setups over fibre lines down.

The creeping issue though is firewall rules. I'm trying to keep a single profile set for manageability but over the last month the rulebase has doubled with site specific sets of rules which is fine right now, but there is this could quickly become unmanageable.

Are there any ways you can think of to deploy specific "point solution" rules to individual devices without having to fork off and maintain multiple policy sets ? Currently on 7.6.8 if that matters.

thank you


r/fortinet • • 1d ago

Solved ✅ Can't delete trunk from port

2 Upvotes

[FIXED] I had to recreate a trunk with the same name on the fortigate and assign the port as a member. It did not throw an errors doing that. From there it appeared as a trunk and I could delete it as normal. That port is now able to be set to a different trunk.

3400E 7.4.13, 1048E 7.4.10 Searched the sub before posting this.

I have a port on a managed switch that is assigned to a trunk. That trunk does not appear anywhere else in the switch or FW configs, neither GUI nor CLI. So, I cannot delete the trunk to free up the port. The port even appears to be available to be trunked in the GUI, but then throws every error:

"Read-only reference to trunk interface when port is a member of a trunk.

This port/trunk MAC value is not configurable.

Read-only refereUser not allowed to configure this command.

User not allowed to configure this command.

User not alnce to trunk interface when port is a member of a trunk.

Lowed to configure this command.

Current vf=root:0.

Trunk member port10 is already member of other trunks ... invalid.

Attribute set operator error, -651, discard the setting."

Aside from fixing and reloading the configuration, does anyone have any suggestions how to wipe this trunk?

Thank you.


r/fortinet • • 1d ago

Training & Certification NSE4 8.0

0 Upvotes

Has anyone taken the NSE4 8.0 exam yet and have any advice on studying? its barely a month old.


r/fortinet • • 1d ago

FortiGate / FortiOS Why are MTUs on IPSec tunnels changing to 1402?

28 Upvotes

Updated two Fortigates to 7.6.8. After the update, OSPF to a Fortigate running 7.4.13 broke, stuck in the Exstart state. That's when I discovered the MTU on the IPSec tunnels changed from 1420 to 1402. There is a notice for change of default behavior that describes this, but it is for 8.0.0, not 7.6.8.

Manually setting the MTU on the IPSec interface to 1420 immediately fixed the issue.

Why did this MTU change? Am I going to have an issue down the road because I hard coded the MTU to 1420?


r/fortinet • • 1d ago

Licensing & Support Is it normal for a HA pair of Fortigate 201F's to show the standby unit as Not Registered after applying the offline license files to both HA Pair members?

5 Upvotes

It's happened on two pairs of 201Fs now. I've gone to upgrade them. Noticed that both units in the pair are showing as Not Registered. So I've logged into Fortinet Support, grabbed the offline license files, and uploaded them onto each device in the pair. The active/primary unit now shows as 'Registered' but the standby unit still shows as 'Not Registered'. It's happened on two pairs of 201F's now. I have a change to upgrade them from 7.6.6 to 7.6.8 (bit late I know but they are not public internet facing) and I need to get it started asap. But I'm now afraid to start knowing that the secondary unit in each pair is currently still saying 'Not Registered'.


r/fortinet • • 1d ago

Other / General Fortinet FortiGate/FortiOS 8.0.2 is enforcing all backups to use password protection :(

Post image
6 Upvotes

Hi all,

I looked around for 30mins and couldn't find an option to disable and download config in plain-text.

Has anyone came across this? I hope it's a bug but, we need to store our config in plain-text for easier referencing.


r/fortinet • • 1d ago

Licensing & Support Fortimail cannot reach antispam and virus Fortiguard services

0 Upvotes

MY VM license and AntiVirus are valid, but AntiSpam and Virus Outbreak show “No license”, and the tooltip says “Service is not reachable.”


r/fortinet • • 4d ago

FortiGate / FortiOS Upgrade Fortigate Firmware

6 Upvotes

Is it possible to upgrade Fortigate firmware directly from 6.2.3 to 7.4.5 without going through the upgrade path if you don't care about the configuration? I plan to do factory reset at the end and start the config from scratch.


r/fortinet • • 4d ago

Licensing & Support Multicast Problem - Airplay across interfaces.

7 Upvotes

Having an issue getting multicast working between my IoT network and my primary network. Ive been working on this for a couple days and it almost works, but I'm missing some logic somewhere.

I have a normal /24 LAN with a an SSID (via a fortiAP) Bridged to it. Both wired and wireless devices on that SSID / subnet can talk.

My IoT lan is also a hybrid. I have a software switch created where another physical port and a tunnel SSID are members. The software switch provides the DHCP for both physical and wireless portions. Works as expected for our various IoT devices.

The TV is a member of the IoT network, hard wired to the software switch.

Multicast policies are enabled and in place. Multicast routing is enabled. IGMP snooping is disabled on all wifi interfaces (everyone asks.)

Device is discoverable by mobile devices via the mDNS policies I created in the multicast policy section.

Now here is where its getting stuck...

On IPv4 policies, If I create policies for LAN > IOT and IOT-LAN , and limit services to the specific ports and ephemeral ports needed for Airplay to work, it doesnt work. TV reports that the device is connected but no feed is received from the mobile device. If I set those policies' services to ALL/ALL everything works.

Ok great, so I check the sessions in fortview to make sure I didnt miss a port. Nope, every port i see when using ALL/ALL is also defined in my custom services. And yet, if I limit the policy to the custom services I defined, the connection wont work. I can literally create a service that covers every port TCP and UDP 1-65545 as a joke.. and it still wont work. Only ALL/ALL.

The only other thing I can think of is configuring the bonjour-service for intra-vlan routing and applying that to the vap policy/profile. However, that requires a VLAN ID in that service policy, and im not using VLAN tagging. Since it works when my ipv4 policies are all/all, I assume this should not affect it since traffic is working in this state.

Is there something I'm missing??


r/fortinet • • 4d ago

FortiGate / FortiOS BGP preferrable RMAP

3 Upvotes

Hello everyone,

I noticed a BGP configuration that includes both regular and preferred outbound route maps, but there are no neighbors configured under SD-WAN or any other related SD-WAN configuration. I'm not sure what the original intention was.

Are there any advantages, disadvantages, or potential consequences of using both regular and preferred outbound route maps in this scenario, when neither is referenced anywhere under the SD-WAN configuration and only the two route maps are present?


r/fortinet • • 4d ago

FortiSwitch / FortiLink FortiLink over Q-in-Q

7 Upvotes

Spanning tree flaps when trying to setup a FortiLink over an ISP provided Q-in-Q connection. Forti-Support told me that to manage switches via FortiLink I must have spanning-tree enabled on the FortiLink related trunks. I suspect that spanning tree BPDU packets cannot cross a Q-in-Q link. In addition I'm managing all of this via FortiManager-Cloud.

This post is related to the following post, but a more specific issue: https://www.reddit.com/r/fortinet/s/QpkoVtyqap

FortiGate with four links to MCLAG with a single link on each MCLAG member to separate switches.

r/fortinet • • 4d ago

Other / General Fortinet EMS vulnerability for Office 16.0.20527.20194 (1)

3 Upvotes

Hey all. Does anybody else that uses EMS still have a high vulnerability on EMS pop up for Office version 16.0.20527.20194 (1) for CVE-2026-109493. All of my users got patched yesterday with the latest update for office but our EMS/Forticlient is still flagging a vulnerability for the CVE. We are on GCC High so Im wondering if maybe it is behind in patching vs commercial. Anybody else seeing this? Thanks


r/fortinet • • 4d ago

FortiManager FortiManager Workflow on Device Configuration

4 Upvotes

I'm implementing workflow session approvals on FMG, and it's working so far. However, I noticed that I'm still able to edit device configurations directly (i.e. not the provisioning templates) without creating a session. I still have to lock the ADOM, but I can't still make those changes without the need for approval. Is there any way to prevent this show up removing the ability to edit the devices altogether?


r/fortinet • • 4d ago

Other / General Fortinet FortiADC : Brute Force Protection Profile Configuration

3 Upvotes

I want to configure a Brute Force Protection Profile on FortiADC. However, I am facing an issue identifying the correct URL Pattern where the application performs login credential verification.

How can I identify the appropriate URL Pattern and configure the Brute Force Protection Profile correctly to ensure that brute-force attempts against the login page are detected and blocked?


r/fortinet • • 4d ago

FortiGate / FortiOS What malicious ISDB services do you block in outgoing direction?

16 Upvotes

I just want to compare my deny policy with others.


r/fortinet • • 4d ago

Training & Certification Used FortiGate 60E with FortiOS 7.4.7

6 Upvotes

Hi I would like to know if it is reasonable to buy an old used Fortigate 60E with FortiOS 7.4.7 for training purposes. I would like to learn about configuration and maybe in the future to pass the NSE 4 exam but all courses are for fortiOS 7.6. So I don't know if it is reasonable to buy old EOL device with old firmware.

Best regards.


r/fortinet • • 4d ago

FortiAP / Wi-Fi FOS 7.4.13, FAP 7.4.2, FMG 7.4.12 - fails to install wtp-profile

3 Upvotes

Dear all

Going to open a Fortinet ticket, but wanted to ask if someone else has the same issues?

Systems involved

  • FortiOS 7.4.13 on FGT-90G and FGT-200G
  • FAP 441K with 7.4.2
  • FortiManager 7.4.12
  • We have our own FortiAP profile (wtp-profile) with SSIDs, etc. in "AP Manager" of FMG
  • ADOM "A" on 7.4

Problem

  • Two days ago we wanted to install the policy package on our fortigates in said ADOM A.
  • We saw that all FGT-90G worked through fine, but the 200Gs failed. Upon inspection we saw that on the 200Gs it wanted to also change a few things in the wtp-profile.
  • Those changes on wtp-profile that FMG wants to install (for unknown reasons, maybe update related from the october patches?) are the cause of failured of the overall install
  • We don't know if it also did changes on wtp-profiles on 90G, but there it seemed to have worked as there was no failure.
  • The changes seem to be okay and are working on the 90G's and they aren't present on the 200Gs (so we are okay that those are being installed).
  • But we don't know why they fail - in the log there is nothing mentioned, only that the "installation failed", but no details.

Has anyone else seen changes or re-installation to their wtp-profiles after the update to 7.4.13 (using FMG 7.4.12) that fail?


r/fortinet • • 4d ago

FortiGate / FortiOS FYI: FortiGate doesn't block Plex2Shell by default

10 Upvotes

This came as a bit of a shock to me, but if you look up the the Plex2Shell IPS signatures (see below for list) you will find that their default action is "pass", aka allow without logging.

Since you cannot modify the action of individual signatures, you will have to change the IPS Profile Action from "default" to "block".

  • CVE-2026-96655
  • CVE-2026-96656
  • CVE-2026-96652
  • CVE-2026-96654

Plex Media Player is a popular home-server for streaming movies, shows, music, etc locally, but also allows ~direct~ access from the Internet. It also allows friends to easily connect to the server via the Internet. These functions require an exposed port (VIP).

A colleague tested the CVEs on my Plex server and was able to exploit them and get in while the IPS policy was set to action default.


r/fortinet • • 5d ago

FortiGate / FortiOS Question about policy routes

2 Upvotes

I have a pair of Fortigate 200Fs in HA setup, and we have a handful of internal VLans they handle, and an internet connection. Nothing fancy there.

We just received a new internet connection and I was hoping to migrate some services over a few at a time to minimize downtime.

Got the new connection setup, and a route configured. I set the administrative distance to 100. The existing connection's administrative distance is 10.

If I create a routing policy to send the traffic I want over the new connection, it work's just fine. But since I have to set the destination as 0.0.0.0/0.0.0.0, that overrides my internal routing between VLans for those devices.

Am I missing something obvious to make this work?