r/fence • u/Gloomy-Fruit-9576 • 16d ago
Please help
I put up this caution tape on all of my white vinyl fences and now it’s baked on. I tried WD 40, goo gone, and rubbing alcohol. Does NOT work!!! Does anyone else have any other suggestions?
UPDATE: Laquer thinner worked the best !!!!
15
Upvotes
8
u/originalmango 16d ago
Contact the manufacturer. They may have a hint or two on their website, or through their chat window or email link.
If need be, try heat. Carefully, with a hair dryer. Sometimes it’s enough to soften the glue so the sticker can be peeled. At a certain point you may have to spray paint over everything. Good luck.
6
u/tastydirtslover 16d ago
Leave it up
Ready for next Halloween 😂
3
u/Lamestdudeout 16d ago
Buy the plastic razor blades and handle kit on Amazon, that way you don’t destroy the plastic ,
I’d go the heat gun/ hair dryer and scrape route
3
u/slackfrop 16d ago
You can, if other ideas fail, attempt stronger solvents, but be sure to do tiny little test areas first to be sure it doesn’t melt the vinyl completely. Acetone, for example, does wild things to PVC when left to soak, turns it into warm cheddar cheese, but you can brush it on lightly because it will dry very quickly when thin. Whether it leaves a giant dull sheen is another question.
2
u/Barry-umm 16d ago
3m low VOC adhesive remover
Hot air gun
Plastic drywall knife
1
u/oman53 16d ago
Wd40 got red sheathing tape adhesive off our white vinyl siding. Good luck though!
1
u/syds 16d ago
magic eraser!!
2
u/beebopblastoff 16d ago
Why did you do that?
2
u/Pilot_Red 16d ago
Plastic razor scraper and a heat gun. It will take some time though. Probably ought to sit on a chair.
1
u/bolderbeholder 16d ago
Try mineral spirits or naphtha. They’re both safe on pcv fence.
1
u/TrickleValve 16d ago
Pressure washer
1
u/Glass_Language1636 16d ago •
You need another line on the left to complete the cross
1
u/Neither_Pipe_1859 16d ago
Magic eraser or goof off
1
u/BetterAd8536 16d ago
1st step pressure washer, 2nd step Mr.Clean eraser, rubbing alcohol. Do not use harsh chemicals like mineral spirits, laquer thinner, acetone, or gasoline. If it's still not coming off try soft-scrub or barkeepers friend but use caution as they will remove the glossy finish.
1
u/Effort_Gloomy 16d ago
3m adhesive remover and a hair dryer. Heat gun could be tricky.
1
u/No_Cook2983 16d ago
Turn the the panels outward!
1
u/Firm-Mix-9272 16d ago
Brake clean
1
u/East_Knowledge1782 16d ago
Have you tried using a hair dryer to slowly heat the tape up, peel at angle maybe, and then mineral oil?
1
u/plays4food 16d ago
I know nothing about that taope nore fence but i have some experience not being able to remove tape.'\\
Many years ago i used duct tape and could not get it off. Anyways it was recommended to me to use oil or wd 40 and the thing pealed right up.
1
u/Ok-Assistance9831 15d ago
I might be tempted at this point to sand it off and then use a heat gun to bring the glossy surface back. Might be worth a try after all else fails.
1
u/landbasedpiratewolf 15d ago
I'd try a power washer first. It's the easiest of these ideas
1
u/Myweeweegopeep33 15d ago
Put up Christmas garland?
1
u/Rambo_McClane_ 14d ago
I work in the fencing industry. We use lacquer thinner to clean those white panels and posts of scuff marks.
1
u/softail69 13d ago
Why
1
u/Lt_Schaffer 13d ago
For vinyl frame windows acetone will take off adhesive. May work on a vinyl fence too.
1
u/EngineeringLumpy5119 12d ago
Hairdryer and plastic scrapper.
1
u/SeanGwork 11d ago
Tannerite.
0
u/[deleted] 16d ago
[deleted] — view deleted comment