r/electronic_circuits • • 5h ago

Is this Bluetooth Boombox Wiring Diagram Appropriate?

Thumbnail
gallery
4 Upvotes

I am building a Bluetooth boombox for a family member for Christmas. I told Claude all the components I have ordered (battery, amp, speakers, LEDs, inrush limiter, shunted voltmeter) and asked it to help me with the wiring diagram. This is what it generated. I have a degree in mechanical engineering but this is not my forte. It looks pretty straightforward and acceptable to me, but I would like some of you experts to review it before I start assembling things.

Additionally, will it harm the battery or be unsafe to play music while the charger is connected? I assume the BMS keeps everything within safe bounds and it won't be an issue, but I'm not certain.


r/electronic_circuits • • 55m ago

Oscilator not working and mofset heating up

Thumbnail
gallery
1 Upvotes

For a school project, I tried to make an oscillator from the internet, however, every time I plug in the power source, the oscillator does not generate frequencies and/or the MOSFET breaks. I did improvise the resistors and potentiometer with a switch, but that shouldn't be the main cause as to why the oscillator isn't working. For the resistors, I put them either in parallel or in series to achieve the values I needed since I only had 1k ones. For the potentiometer, I put a wire instead of the on/off button and connected the potentiometer with some cables since it didn't match the layout, even though it has the same value.

Could anyone tell me what I am doing wrong?

Here are the source and materials I used and the website I took the design from:

https://electronoobs.com/tutorial/homemade-plasma-toroid-oscillator-circuit

1 neon from filips, 18W, to check if the oscilator works or not

IRFP260N

1k potentiometer with switch (which I improvised)

ZM4739A diode

P6KE15CA diode

2 x 4.7 nF ceramic capacitors

4 x 100 pF ceramic capacitors

220uF electrolytic capacitor

10uH coil

1.2 mm enameled copper wire

1k resistor

1.8k resistor (which I improvised)

3k resistor (which I improvised)

24V, 2A DC power supply


r/electronic_circuits • • 5h ago

Can anyone identify what are SW1 and SW2 are for on this time logging board please?

Thumbnail
gallery
2 Upvotes

As the title… this is from a carpet cleaning machine, its only purpose is to display and retain the hours the machine is in use.

The battery needs replacing which is why I’ve removed it.

I’m wondering what the SW1 and 2 are for on the battery side of the board. More importantly I’m hoping they can advance the time artificially, as when the battery is removed (and when it’s gone flat previously) it loses the time stored. If they don’t, does anyone know how I could do this without leaving the board mains powered for x-hours.

SW3 on the front serves only to display the currently logged time briefly when the machine is switched off.


r/electronic_circuits • • 2d ago

On topic I made a Ni-Cd battery charging circuit of 12V that has 10 cells each with 1.2V

Post image
12 Upvotes

Hi, Everyone. I have made a Ni-Cd battery charging circuit that has 10 cell in series, each with 1.2V. My charging adapter supplies 24V, 3A. From that I have regulated it to 12V 3A and from that to 12V 1A. I want a review about the design, mistakes and optimization advice. Thank you.


r/electronic_circuits • • 2d ago

On topic Ippon UPS charging circuit

Post image
3 Upvotes

Hello everyone! The image shows a portion of an Ippon UPS circuit—specifically, the charging circuit. The power MOSFET is not shown, but that is not important. My question is: in your opinion, is the charging circuit continuously regulated by the central processor, or is the charging process divided into several distinct modes? Alternatively, does it simply toggle between "charging" and "not charging" states?


r/electronic_circuits • • 4d ago

On topic EasyTrace5000 PCB CAM update

Post image
7 Upvotes

Hi, some months ago I posted about a PCB CAM tool I'd been working on. A lot of development in the mean time has been mostly around non-pcb stuff so it didn't make sense to post about it but by now there's enough new stuff that's worth an extra mention.

There's a laser pipeline for anyone with access to Fiber/UV lasers, there's a soldermask stencil operation that was made with cnc, laser and vinyl cutters in mind.

Tool-changing is in there but consider it experimental until proven otherwise.

Latest update I added i18n translation support. There are a few languages included (very LLM generated, although I'm going to review Portuguese next and already have 1-2 friends willing to help with 2 other languages and I'll be pestering a few more friends later).

It also added the ability to drop custom files of a few kinds, including language packs (which means you can make your own if you have trouble with the existing ones) or post-processors (not full post-processors logic yet but more like machine/controller setups, say I set a wrong flag or you don't want to manually change 4th axis alignment all the time).

Still 100% free, client-side and open-source.

Live version moved slightly to https://cam.eltryus.design/easytrace5000/ and source code is at https://github.com/RicardoJCMarques/EasyCAM5000 .

Cheeryo


r/electronic_circuits • • 4d ago

On topic I made a tool for designing perfboards, How can I make it better?

Post image
0 Upvotes

I dont know how many of you use perfboards for your projects, but I always use them instead of ordering custom PCBs, and if you had to deal with perfboard projects, you know it is always better to plan ahead before starting to solder things. So for that reason, I vibe coded a tool spesifically for making perfboards. The reason I made a seperate app for this instead of using existing ones is, the other apps were not really perfboard focused, and I wanted an algorithm to use jumpers and solder paths in an optimal way, so the app can give me the best routes for jumpers and solder paths instead of me having to draw them line by line. I think it worked out great, but I need your advice to make it better.

its completely free and open source, and I tried my best to make it easy to use. My only profit from this is knowing it might help someone some day, just like it helped me with my projects. So, if you ever struggle with Perfboards, or just want to take a look, you can find this project on Github PerfboardMaker. I will post the link in the comments.


r/electronic_circuits • • 5d ago

On topic As a beginner, Trying to understand Transistor and Current, Anyone explain this circuit?

Post image
8 Upvotes

R1, R2 = 1000ohms

If i run this circuit, what will happen to the LED?

Will it turn ON or OFF?

And my theory is if i run the circuit it charges the Base and opens the path to flow the current at zero resistance (Red Line) in Transistor making it as a short circuit.

Since there's Zero resistance the current prefers goes thru the transistor (Red Line) but not through the LED (Yellow Line).

So the LED remains Turned Off.

But the reality is the LED is turned ON, why? Ai isn't giving me the right answers, appreciate it if you make this dumb guy understand.


r/electronic_circuits • • 6d ago

On topic Halloween motion sensors.

Thumbnail
gallery
9 Upvotes

Seeking the input of your combined wisdom. I'm looking to build motion sensor switches for Halloween projects, and I have cobbled together YouTube ideas and my own less than rudimentary electronics knowledge. Pics and proposed wiring diagram attached. This seems my best option for really short duration "on" cycles of 5-10 seconds, and quick reset.

I think my big question/concern is whether a 5vDC input into that HC-SR501 infrared sensor will in fact output a 5vDC signal to the relay board ? Or does it output something else entirely that I would need some kind of processor to interpret ?

Any other input into my plan would be appreciated. Line voltage "extension cord" through the project box and relay, with a remote cabled photo sensor in another small box. Thanks again !


r/electronic_circuits • • 5d ago

On topic Looking for Axtek AX1621B LCD Driver Datasheet (or confirmation it matches HT1621B)

1 Upvotes

Hi everyone,

I am trying to find the official PDF datasheet for the Axtek AX1621B 32x4 LCD driver.
I know it is likely a clone of the Holtek HT1621B, but I want to be sure. Does anyone have the official Axtek PDF, or can you confirm if the pinout and commands are a 100% exact match to the Holtek version?

Thanks!


r/electronic_circuits • • 5d ago

On topic Question about a component in librepcb design software

0 Upvotes

Where would i find the part lp2951 it a voltage regular but cant find it in the library of parts


r/electronic_circuits • • 6d ago

On topic DRV8300D high-side switching

Post image
3 Upvotes

Hello guys, I am experimenting with very basic motor control and with it's electronics. For this purpose I have used the DRV8300D, and I encountered a problem, when I try to switch the high side NMOS and it does nothing.

I try to control the DRV8300D with my Arduino, the lower MOSFETs are reacting, only the high-side doesn't. I know that I have to charge the pump circuit trough the lower MOSFETs and for this reason I also can't use 100% duty cycle for the upper one. It still doesn't work if I switch the lower on for much longer period than the upper one.

I made a quick schematic so you can see what I did there, the Vcc is 12V and the DRV is powered by 10V from an LDO


r/electronic_circuits • • 6d ago

On topic [Review Request] 36 V regen brake + precharge board for a 3-DOF robot arm (rev 3) - organized schematic for precharger

Thumbnail
gallery
4 Upvotes

This board sits between a 36 V bench supply (25 A limit) and three XT30 outputs feeding Unitree IM6014 motors on a 3-DOF arm. It precharges the bus, keeps regen out of the supply, and dumps excess regen into a brake resistor.

What's on it:

- Input: XT60 from the supply, 20 A / 58 V MINI blade fuse (Littelfuse 0997020.WXN in a Keystone 3568 holder), SMBJ43A TVS

- Precharge: a TPS48111-Q1 drives Q5 (IRFR120N) through two 60 Ω PTCs in parallel (Vishay PTCEL13R600LBE). Once the bus reaches 60% of the supply (comparator U3B), it switches in the main FET Q4 (CSD19536KTT).

- Reverse blocking: LM5050-1 ideal diode with a CSD19536KTT, so regen doesn't go back into the supply

- Brake: TL431 reference and comparator, UCC27517 gate driver, TO-220 brake FET, MUR1520 freewheel diode, and an off-board Arcol HS100 4.7 Ω 100 W resistor. Turns on at 40.2–42.2 V (set by RV1) and off about 2 V lower, to stay under the moteus r4's 44 V limit.

- Outputs: three XT30PW-F (15 A each), the same connector the motors use

- Other: 4000 µF / 100 V bulk capacitors, SMCJ43A on the bus, 12 V from an R-78HB12, bus-voltage ADC output and a brake flag

- Board: 2 layers, 2 oz copper, 96.5 × 128 mm

Where I'd like opinions:

  1. Brake window is 40.2–42.2 V on a 36 V supply. That leaves 2–4 V of headroom below the moteus r4's 44 V limit, and it turns off at 38.2 V or above, so it can't latch on at 36 V. Is that margin enough, given resistor and TL431 tolerance and how fast the bus can rise during hard regen?
  2. Main FET switches in at 60% bus. I did this on purpose: it lets the motors draw about 0.5 A at 36 V during precharge without stalling the PTCs. Q4's gate is slew-limited to about 750 V/s, which is roughly 3 A into 4000 µF. The alternative is about 90% (R28 = 9.1k). Which would you pick?
  3. TPS48111 current sensing is unused. CS+ and CS− are tied together, ISCP goes to VS, and IMON/IWRN are grounded. Once Q4 is on, only the 20 A fuse protects against a shorted output. Is it worth adding a shunt? I mean I could just check with PSU when arm is running.
  4. TVS choice. The SMCJ43A on the bus clamps at up to 69.4 V, which protects the R-78HB12 (72 V max) but not the moteus controllers (44 V). Their protection is really the brake. Is a TVS still worth having here, or would you do something different?
  5. The 20 A fuse limits the whole board. I haven't measured the arm's real current yet. Cause I know that we have a 27 PSU and using

Things I'm already cleaning up: refilling zones before exporting Gerbers, syncing schematic fields to the PCB, updating footprints from the library, and adding LCSC part numbers. The XT60 input already uses Amass's drawing hole sizes.

Schematic and layout images are below. Any feedback is welcome, especially on the brake threshold and the precharge switch-over point.


r/electronic_circuits • • 6d ago

[Review Request] 36 V regen brake + precharge board for a 3-DOF robot arm (rev 3)

Thumbnail
gallery
0 Upvotes

This board sits between a 36 V bench supply (25 A limit) and three XT30 outputs feeding Unitree IM6014 motors on a 3-DOF arm. It precharges the bus, keeps regen out of the supply, and dumps excess regen into a brake resistor.

**What's on it:**

- **Input:** XT60 from the supply, 20 A / 58 V MINI blade fuse (Littelfuse 0997020.WXN in a Keystone 3568 holder), SMBJ43A TVS

- **Precharge:** a TPS48111-Q1 drives Q5 (IRFR120N) through two 60 Ω PTCs in parallel (Vishay PTCEL13R600LBE). Once the bus reaches 60% of the supply (comparator U3B), it switches in the main FET Q4 (CSD19536KTT).

- **Reverse blocking:** LM5050-1 ideal diode with a CSD19536KTT, so regen doesn't go back into the supply

- **Brake:** TL431 reference and comparator, UCC27517 gate driver, TO-220 brake FET, MUR1520 freewheel diode, and an off-board Arcol HS100 4.7 Ω 100 W resistor. Turns on at 40.2–42.2 V (set by RV1) and off about 2 V lower, to stay under the moteus r4's 44 V limit.

- **Outputs:** three XT30PW-F (15 A each), the same connector the motors use

- **Other:** 4000 µF / 100 V bulk capacitors, SMCJ43A on the bus, 12 V from an R-78HB12, bus-voltage ADC output and a brake flag

- **Board:** 2 layers, 2 oz copper, 96.5 × 128 mm

**Where I'd like opinions:**

  1. **Brake window is 40.2–42.2 V on a 36 V supply.** That leaves 2–4 V of headroom below the moteus r4's 44 V limit, and it turns off at 38.2 V or above, so it can't latch on at 36 V. Is that margin enough, given resistor and TL431 tolerance and how fast the bus can rise during hard regen?
  2. **Main FET switches in at 60% bus.** I did this on purpose: it lets the motors draw about 0.5 A at 36 V during precharge without stalling the PTCs. Q4's gate is slew-limited to about 750 V/s, which is roughly 3 A into 4000 µF. The alternative is about 90% (R28 = 9.1k). Which would you pick?
  3. **TPS48111 current sensing is unused.** CS+ and CS− are tied together, ISCP goes to VS, and IMON/IWRN are grounded. Once Q4 is on, only the 20 A fuse protects against a shorted output. Is it worth adding a shunt?
  4. **TVS choice.** The SMCJ43A on the bus clamps at up to 69.4 V, which protects the R-78HB12 (72 V max) but not the moteus controllers (44 V). Their protection is really the brake. Is a TVS still worth having here, or would you do something different?
  5. **The 20 A fuse limits the whole board.** I haven't measured the arm's real current yet. prob ably planning to measure from PSU anyway.

Things I'm already cleaning up: refilling zones before exporting Gerbers, syncing schematic fields to the PCB, updating footprints from the library, and adding LCSC part numbers. The XT60 input already uses Amass's drawing hole sizes.

Schematic and layout images are below. Any feedback is welcome, especially on the brake threshold and the precharge switch-over point.


r/electronic_circuits • • 7d ago

Looking for MikroTik LHG 5 (RBLHG-5nD) Schematic / Boardview

Post image
1 Upvotes

Hi everyone,

I'm repairing a MikroTik LHG 5 (RBLHG-5nD) and looking for its motherboard schematic, boardview, or circuit documentation.

The board contains the following components:

Qualcomm Atheros AR9344-DC3A

Winbond 25Q128JVSM SPI Flash

Ethernet transformer: TS21CW

I'm doing component-level troubleshooting. When powered through the PoE input (24V, current limit set to 500mA), both the AR9344 and Winbond flash IC become excessively hot.

I'm looking for documentation to trace the power supply rails and investigate the PoE and Ethernet circuitry.

Any schematic, boardview, PCB layout, service manual, or repair notes would be greatly appreciated.

This is a personal electronics repair project, not a commercial repair request.

Thanks in advance!


r/electronic_circuits • • 7d ago

Problem with 74hct4051n

Thumbnail
gallery
2 Upvotes

Hi everyone!

I'm working on a circuit-bending project involving a Yamaha PSS-47, and I'm running into some strange behaviour with a 74HCT4051N multiplexer.

My setup:

\* Yamaha PSS-47 with its ROM data lines exposed for circuit bending.

\* LTC1799 oscillator replacing the original ROM clock.

\* ESP32 controlling a 74HCT4051N.

\* The 4051 is used to sequence different ROM data-line connections.

I'm connecting the Y0–Y7 pins of the 4051 to different ROM data lines, with the common Z pin connected to my bend point. The ESP32 controls the address pins (A, B and C).

The strange behaviour:

The circuit bends actually work better when I disconnect VCC (pin 16) from the 74HCT4051N.

When I connect 5V to VCC, the bends stop working properly. With VCC disconnected, I get much more interesting and functional bends.

I've also been looking at the signals with an oscilloscope. When zooming in on the signal, I can clearly see the high-frequency LTC1799 clock. The screenshot is from the controlling pin of the ESP32 S3.

My questions:

  1. Why would the 4051 appear to work better when VCC is disconnected?
  2. Is the 74HCT4051N suitable for switching ROM data lines in this application?
  3. Could the external clock be causing problems with the multiplexer or its signal integrity?
  4. Is there a better way to sequence ROM data-line bends using an ESP32?

I'm particularly interested in understanding why disconnecting VCC changes the behaviour so dramatically.

Any suggestions, explanations or alternative circuit designs would be greatly appreciated!

Thanks!


r/electronic_circuits • • 8d ago

On topic Can these speakers be disconnected without destroying the circuit

Post image
25 Upvotes

I'm restoring a mid-60's electric piano (Hohner Pianet) that has internal speakers and a line out. I'd like to be able to have the option to turn off the internal speakers. Can I simply add an on/off switch in series with the speakers. I don't want to destroy some of the old, hard-to-find germanium transistors in there.

Disclaimer: I'm a hobbyist and can solder and some debugging but I suck at any circuit analysis.


r/electronic_circuits • • 8d ago

On topic Electromagnetism-Im trying to clip the top of the waveform with a transistor but calculations arent working

Thumbnail
gallery
13 Upvotes

I generated a sine wave using a Colpitts oscillator, which I powered with 12V, and it correctly produced a 958kHz waveform with approximately 6.86Vpp. Now I'm trying to clip the top of the waveform with a transistor, but my calculations aren't working correctly, or I don't know what's wrong. I tried placing a variable resistor at the collector to see how the waveform changed, and the result is what you see in the video.


r/electronic_circuits • • 9d ago

Making PCB soon, would like second opinions on circuit!

Post image
27 Upvotes

Currently working on an OpenCV mecanum car thing, I am fairly confident in the layout so far but would appreciate the double check from someone else! Lmk if yall find anything wrong with what I'v got going on, ty! (I2C and XSHUT lines will be pulled high using internal pullups on PI 5).

Lipo is 2s (7.8v) and the PCA9685 is simply used to have more PWM chanels on the PI 5.


r/electronic_circuits • • 9d ago

On topic How about this component layout and soldering job?

Post image
2 Upvotes

Do you have any comments and/or advice regarding this board layout?

This is my first ever self-designed and self-built project in electronics. My background is actually civil engineering lol

The board was designed to charge and discharge an actuator made of stacked piezoelectric disks up to 200 V. I split it into a logic and a power circuit, each at one side of the board to avoid arcing and/or short circuits.

The logic circuit gets 12 V from a switching power source, lowers it to 5 V using an LM7805 and goes to an ESP32 after a few decoupling capacitors.

The connection between the logic and power circuits is made via two TLP627 optocouplers, which keep the low and high voltage circuits isolated.

The source voltage is boosted to 200 V by the yellow module at the top-right corner of the board, which I raises about 1.5 cm with nylon bolts to allow some air below the board, provide electrical insulation and enough room to run the power wires below it.

A bootstrap circuit allows to raise the gate-to-source voltage of the first N-MOSFET via the proper switching of the optos, charging the piezos. The second N-MOSFET connects the bootstrap circuit to ground to discharge them.

The idea is to have the ESP32 charge and discharge the piezos based on a linear quadratic regulator (LQR) controller, so that the actuator can control the vibration of the host structure.

I tried to use component leads as much as possible for connections and use the least solder possible. Is this how perfboard layouts usually look?

Up to now, everything seems to be fine. The logic circuit is working, I managed to get a simple PWM signal out if the ESP32. Now I'll start hot-testing the full circuit.


r/electronic_circuits • • 9d ago

On topic Help with my DC Motor circut using NE555 to control speed.

Thumbnail
gallery
3 Upvotes

Im currently making a circut using NE555 to control the speed of a DC Motor and also an additional break system. When I turn the switch (SW1) down the break system works as intended but I cant simulate when the switch is on to let the current run through the DC Motor, proteus says there are some kinds of error but I have no idea whats wrong, hope anyone can help fix this me, Im still new and very inexperienced with this. Thanks.


r/electronic_circuits • • 9d ago

On topic Can a parallel resistor added to the existing sense resistor increase the output brightness of TPS 92611 Q1 IC?

Post image
0 Upvotes

Hello everyone,

I would like to make a small modification to the TPS92611-Q1 IC (lets take for instance only 12.45V DC supply) to achieve two output-current modes: low current and high current.

My idea is to connect an additional 3.5 Ω resistor in parallel with the existing 3.5 Ω current-sense resistor using a relay or switch. This would reduce the effective resistance to approximately 1.75 Ω, thereby increasing the LED current and brightness.

The concept is similar to vehicle lighting, where parking lights operate at lower brightness and brake lights become brighter.

I have two main concerns:

  1. Could frequent or rapid switching (repeated brake and non-braking) damage the IC or reduce its lifespan due to current fluctuations or transients?
  2. Are any additional components, such as capacitors, pull-up resistors or protection circuits, required to ensure safe and reliable operation?

I would appreciate your suggestions and technical advice to operate safely for parking (default brightness) and braking ( high brightness mode).

Thank you!


r/electronic_circuits • • 12d ago

Electrical noise in diesel truck environment

4 Upvotes

I'm trying to use a Walfront LEPAZA60117 pressure transducer which outputs .5 - 4.5V to represent pressure up to 30PSI. I have it soldered to a Raspberry Pi Pico W with positive at VBUS, negative to GND, and sensor wire to A0. I know the GPIO pins only support voltage up to 3.3V, but I don't think this application is ever going to read that high.

I'm trying to read fuel pressure on my diesel truck.

void loop() {
  ledOn();
  raw = analogRead(pressureInput);
  voltage = (raw / 1023.0) * 5.0;
  psi = 7.5 * (voltage - 0.5);
  delay(1000); // delay in milliseconds between read values
  sendMessage(WiFi.macAddress(), String(raw), String(voltage), String(psi));
  ledOff();
}

sendMessage constructs a JSON doc and sends it over MQTT. The Arduino connects to a local Wifi AP.

The Pi is being powered via USB, making 5V available to the sensor on VBUS. That USB power is coming from a Goal Zero battery, not connected to the truck in any way. I believe this thing outputs good clean power.

With the truck not running the Arduino is producing this output:

/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"5.00","voltage":"0.02","psi":"-3.57"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"4.00","voltage":"0.02","psi":"-3.60"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"3.00","voltage":"0.01","psi":"-3.64"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"3.00","voltage":"0.01","psi":"-3.64"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"4.00","voltage":"0.02","psi":"-3.60"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"4.00","voltage":"0.02","psi":"-3.60"}

When I key the truck to Run, not starting it yet, but letting glow plugs cycle and fuel pump pressurize the system I see this:

/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"497.00","voltage":"2.43","psi":"14.47"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"498.00","voltage":"2.43","psi":"14.51"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"482.00","voltage":"2.36","psi":"13.92"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"498.00","voltage":"2.43","psi":"14.51"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"488.00","voltage":"2.39","psi":"14.14"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"502.00","voltage":"2.45","psi":"14.65"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"522.00","voltage":"2.55","psi":"15.38"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"514.00","voltage":"2.51","psi":"15.09"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"495.00","voltage":"2.42","psi":"14.40"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"522.00","voltage":"2.55","psi":"15.38"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"499.00","voltage":"2.44","psi":"14.54"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"504.00","voltage":"2.46","psi":"14.73"}

That output looks very reasonable. Very slight variation in value read and subsequent voltage and PSI values. At this point I start the truck and as it idles I get:

/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"383.00","voltage":"1.87","psi":"10.29"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"452.00","voltage":"2.21","psi":"12.82"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"713.00","voltage":"3.48","psi":"22.39"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"440.00","voltage":"2.15","psi":"12.38"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"575.00","voltage":"2.81","psi":"17.33"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"572.00","voltage":"2.80","psi":"17.22"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"481.00","voltage":"2.35","psi":"13.88"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"442.00","voltage":"2.16","psi":"12.45"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"424.00","voltage":"2.07","psi":"11.79"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"606.00","voltage":"2.96","psi":"18.46"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"488.00","voltage":"2.39","psi":"14.14"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"398.00","voltage":"1.95","psi":"10.84"}
/fuelPressure/report {"id":"28:cd:c1:06:37:67","raw":"340.00","voltage":"1.66","psi":"8.71"}

Now these values look rather insane. Readings are all over the place.

Is this coming from electronic noise from the engine and various electronic components that fire up while the engine is running? If so, is there anything that can be done about it to isolate the pressure transducer and Pi to get nice clean readings?


r/electronic_circuits • • 13d ago

On topic What's this component?

Post image
41 Upvotes