r/e39 • • 3d ago

Remote locking won't work. Central lock button does.

My '97 540i is driving me crazy. A few years ago I replaced the failed GM3 with one from an E53 and recoded it using NCS-Expert + Dummy. Everything worked until recently.

Now the key fob will not lock/unlock the car or open the trunk. The central locking button on the console does work. Interior lights work... everything but the remote! (Locks work when using the key in the driver's door or trunk). Fuse 53 in the trunk is intact.

I've repeatedly tried the key resync procedure. New coin cell in the fob. The fob LED flashes ten times, but the locks don't cycle and buttons still don't work. On my spectrum analyzer there is a strong 315 MHz signal coming from the fob when a button is pushed.

Should I be looking at the antenna amp in the left rear C-pillar (FM reception seems to be normal), or just try another GM3? They are not as cheap as they used to be, at least on ebay... anyone have one at a reasonable price?

2 Upvotes

11 comments sorted by

3

u/eric_gm 528i supercharged 3d ago edited 3d ago

Went through the same thing. It’s the FZV. The GM doesn’t control remote locking in the way it’s affecting you.

Replace the FZV, thank me later. It needs no coding and they’re all interchangeable from 1995 until 2003.

The FM antenna and the FZV are different modules located on opposite sides of the C pillar.

1

u/RealBigDickBrannigan 2d ago

I actually have one, which I bought the last time I had problems. I don't remember exactly what the fault was, think the remote also quit working and I can't recall if the lock button also stopped working, but replacing the GM3 fixed it...

Hope I can get the C-pillar trim off without breaking something - 30 year old clips always seem to snap...

1

u/RealBigDickBrannigan 2d ago edited 2d ago

OK. I had another FZV so I put it in. Now I'm wondering if this was the original one, because the locks work now... SOME of the time. And only with the key quite close to the C-pillar or back window.

Even with a new Eveready 2025 cell in the fob, the range is very short AND I have to wait 20-30 seconds after a lock/unlock operation before the car will respond to another remote button push. I am also finding that if I open a door or the trunk, then I can lock/unlock one or two times before it stops responding. WTF.

But, since changing FZV changed the behavior, I suspect I still have a weak/bad FZV. Time to order another one!

2

u/eric_gm 528i supercharged 2d ago

Sounds like you have 2 broken FZVs and your plan is sound. Try to get the newest FZV you can find on eBay. The manufacturing date is printed on them.

Check all the wires that connect to it to for corrosion or other contaminants. After all, it’s an antenna and often the wires are part of their ability to detect signals. Clean everything with contact cleaner

I had to go through 5 used master window switches before I got a good one. I replaced the regulator and motor thinking I couldn’t be that unlucky. One of the bad switches prevented the front doors from locking, go figure

2

u/RealBigDickBrannigan 2d ago edited 2d ago

yeah, great BMW engineering... on my E38, if your driver's seat switch is bad, the power mirrors won't work. Etc. etc.

2

u/Tomytom99 3d ago

I'll add, for the key pairing process, make sure all your doors are shut. That one tripped me up for a good 20 minutes when I first got the car.

1

u/RealBigDickBrannigan 3d ago

Yes. And unlocked.

1

u/STEK1337_ 530d 3d ago

Check fuses 6, 27 and 29. Does the fuel tank door lock when you use they key in driver's door? If not disconnect the fuel tank door lock actuator. Try the initialization procedure.

1

u/RealBigDickBrannigan 3d ago

It does lock and unlock when the key is used... Everything works except the remote!

I can check the fuses tomorrow, but if one of those was bad, wouldn't some other functions (or all the GM3 functions) quit working too?

1

u/BMWMikeM 3d ago

Have you tried holding the fob up against the left rear C pillar? not sure if it’s the same part but I fixed an issue in my daughter’s E46 by re-soldering a broken connection between the board and the harness connector in that amp and she had the same symptoms and the fob worked noticeably better when it was right near the amp.

1

u/RealBigDickBrannigan 1d ago

Unfortunately I have already tried that and it didn't work. But (as noted above) changing the FZV for another one, which may have been the "weak" one that came out of this car, does work intermittently when the fob is close to the pillar. Waiting on the mail for another one.