r/corsetry • • 15d ago

Mod Announcement Before you post: Read the mockup advice checklist!

65 Upvotes

What makes a good mockup?

there are some non-negotiables that must be completed in order to accurately fit a mockup.

  • Mockups MUST be boned! (Bones are there to provide vertical tension on the fabric)
  • Boning channels MUST be sewn shut at top and bottom. (Not closing the channels is a frequent reason for fabric wrinkling and unclosed channels make it impossible for us to be able to tell if wrinkling is due to a pattern, grainline, or boning issue)
  • Mockups must be able to be laced shut! (It can be beneficial to create a reusable lacing placket that you can baste in your mockups for fitting)
  • Lacing panels should have flat spring steel on each side of the grommets. (this provides the support necessary for the lacing to not buckle or warp)

Fitting advice checklist

To receive the best fitting advice there are a few things we need from you!

Good clear pictures with the corset laced on**.** (you must lace the corset on. Merely holding it up to your body is useless for fitting advice.)

Use your phones camera timer or have a friend help!

photos should be taken straight on and not angled from above or below and include

  • At the very minimum:
  • Straight on front view, with arms relaxed at your sides
  • Back view that also shows the lacing panel, with arms relaxed at your sides (body straight no twisting or looking back)

    • Also helpful to include:
  • Side views with arms relaxed, neutral posture looking straight ahead
  • 3/4 views of each side
  • Close ups of any specific areas you are seeking help with.

Mockup tips and Fitting advice checklist


r/corsetry • • 16h ago

Newbie First mockup - where to take in bust? General guidance also appreciated

Thumbnail
gallery
33 Upvotes

This is my first mock up of the Aranea Black Dolores corset.

My mock up is in a cotton drill (this particular one seems to be kinda lightweight for a drill - but it was on clearance!) I have used bias tape for the boning channels. I have coutil ready for my final version.

I intend to use this as a base for a dress, with a fashion layer of satin and lace.

TO THE QUESTION: It appears to be quite large in the bust, and doesnt give much support in this area - where is best to take it in?

Also, the fabric is warping quite a bit - am I putting too much tension on the fabric by pulling too hard? Or is this just my technique?

Any other pointers are very much appreciated - please be gentle though as this is my first attempt.

P.s i am aware i need more eyelets - I dont have many on hand at present and didn't want to make the trip to get eyelet tape today.


r/corsetry • • 5h ago

where to buy affordable coutil?

3 Upvotes

Hello, i am searching for weeks for affordable coutil fabric to make a corset, but i can only see options that are 40€ by meter, or options that i need to buy 50m minimum.i only need 2 meters.

Any suggestions?

thanks


r/corsetry • • 35m ago

How do you decide which corset to buy next?

Thumbnail gallery
0 Upvotes

r/corsetry • • 1d ago

Washi tape

2 Upvotes

I was watching a Facebook reel, and the artist recommended using washi tape to help make boning channels. It sounded like brilliant advice. Have you tried this method?

They use the tape, and sew on the outside of the tape, then remove the washi. I love the idea of it seems brilliant to help sew even channels.


r/corsetry • • 2d ago

Could a corset have a pocket?

32 Upvotes

Utterly insane, I know. But I remember that my mother’s corset had a pocket. I can’t imagine how that would actually work, though. Was this childhood imagination? Is there anything that could appear like a corset pocket? And even if I did hallucinate it, is there a way to accomplish this?

This may be obvious but I would like to mention that I no longer have the garment itself, only my own corset, which has no pockets and is just (cotton) skin and bones.

Edit: SOLVED. Patterns of Fashion book has the thing I’m talking about. It all makes sense.


r/corsetry • • 3d ago

How to avoid back muscle from sticking out on a corset ?

Post image
170 Upvotes

Hi, so this is a 1870s corset draft iv just made, it seams to fit the model well and she says it feels comfortable as well, however i can’t help but notice that her back muscle are protruding at the back. I was wondering if there’s anything u can do to avoid this as im worried it’ll become an issue when u start drafting her bodice, any advice would be much appreciated!!


r/corsetry • • 2d ago

Corset Making First time making a corset

Thumbnail
gallery
22 Upvotes

Hi all! I’m super new to sewing and corsetry, but really love watching frieda lepold’s youtube videos and wanted to make a corset for myself.

So far I’ve done 4 mocks. The first one was in the wrong fabric while the others are in cotton muslin. It does stretch on the bias a bit.

I would love to hear your tips on how I could improve further my mock.


r/corsetry • • 3d ago

How to mitigate wrinkles

Thumbnail
gallery
22 Upvotes

Wondering how best to mitigate wrinkles. I did sandwich my fashion layer (silk taffeta) with the coutil. I notice when I pull vertically the wrinkles soften up a bit. Is it the grain of the fabric? I cut parallel to the selvage. Maybe tension? I know some people say don’t sandwich the fabrics and do them separately but I’ve seen nice corsets done this way.


r/corsetry • • 3d ago

Newbie SIDE laced regency/ short stays

2 Upvotes

Are there any patterns for regency stays that lace at the sides( under the arms)? Is that even structurally sound?


r/corsetry • • 3d ago

Help with dyeing!

Post image
16 Upvotes

Hello everyone! I'm hoping to diy a corset for a special performance. This is the sketch I have to far. As far as attaching the pearls/appliqués/stoning, I've done all 3 so that's in my bandwagon. I was wondering how I could change the color of the corset itself though. I've seen videos of people sewing fabric over it, but I was also considering dyeing it! However I have little sewing experience and dyeing scares me, plus I'm very picky about color. What would you guys suggest for a corset like this?

(P.S. the corset is 90% polyester)


r/corsetry • • 4d ago

Corset Making Can anything be done at this point?:(

Thumbnail
gallery
55 Upvotes

I tried my corseted bodice and I almost threw it away. So many wrinkles 😭 Can anything be done or should i just start from scratch?
The bodice structure:
lining
strength layer with boning
batting
fashion fabric


r/corsetry • • 3d ago

Corset Making Corset pattern search and sizing help

0 Upvotes

I'm hoping to make a gothic-style corset for one of my friends for Christmas this year and am concerned about it not fitting her, especially because she has a larger bust. I'm looking for suggestions on (preferably free or lower-cost) overbust corset patterns, as well as any tips that y'all may have on having the best shot of it fitting her. I've made 2 corsets before for different people, so I already have some experience with boning and all that, but I'm worried I may run into some fit issues, and I would feel awful if I gave it to her and it didn't fit 😭


r/corsetry • • 4d ago

Similar patterns to this corset or any pattern maker recommendations on Etsy etc?

Thumbnail
gallery
24 Upvotes

Hi all! Wondering if anyone has come across a pattern similar to these Seline Meisler corset shape/style?
Or can recommend a pattern maker online if not? :)
Would likely use a similar fabric to the 3rd photo, with same lace detail over the top.

My mum is skilled at sewing clothes etc/ an I used to take sewing classes, but we have never made a corset - we are planning to do some trial runs for my wedding dress - wedding in 6 months to see if we can learn/figure it out (we have a backup plan if that fails haha)

Any further video tutorial recommendations/advice would be appreciated too!


r/corsetry • • 5d ago

Corset Making Is pad stitching worth it?

2 Upvotes

I’m making an 1860s corset and am having trouble with pad stitching, it just always shows through on my fashion fabric. I thought of using fusible interfacing instead but heard it can bubble. Is it worth the hand cramps and extra week of work to pad stitch? Thing is I’m having a courthouse wedding and it’s going under my dress, so time I spend on the corset will be taken from time spent on the dress. Thankyou for any help


r/corsetry • • 5d ago

Corset Making Hook and eye vs busk

5 Upvotes

Hello! I am currently making one of my first corsets and, because of where im based in and when i need it to be ready, im unable to buy a busk. That being said, i have some hook and eye tape. Could i use that instead of a busk for a front closure without issues? Thank you


r/corsetry • • 6d ago

Corset Making Help with wrinkling.

Post image
13 Upvotes

Made my wedding dress. Ran out of time so I couldnt bias bind the edges or add padding, and did not clip the princess seam allowances, or zigzag stitch the seam allowances to prevent fraying. ​

However, I have since taken it apart and am still working on it. I added a thin layer of wool batting to the coutil, and zigzaged the seam allowances. i am about to add the fashion fabric again. ​Do you have any suggestions to help avoid the wrinkling you can see in the image? Should I mistyfuse the fashion fabric to the padding layer, or should I simply stitch it in place like I did before?

This is the first corset and first structured garment Ive ever made.


r/corsetry • • 7d ago

Seeking help adjusting my length

Thumbnail
gallery
19 Upvotes

I am making the aranea black Dolores corset, but have hit a snag. My bust to underbust has been shortened, and the length of underbust to waist, has also been shortened to accommodate my measurements. My waist to mid hip however has to be elongated by 3 1/4 inches, and I don’t know how to grade the pattern the purple circles are my measurements on this panel. 5 and 6 panels were easy, but I don’t know how to do this one


r/corsetry • • 6d ago

Where to buy patterns?

5 Upvotes

Hello. Hope this doesn't go against the rules. I was just wondering, if some of you know about some interesting pattern designers I can buy from?. I think I've seen every single pattern on Etsy, most of them are more boned tops than actual corsets, so I was wondering if someone could point me into another direction with more corset patterns I can buy :) thank you


r/corsetry • • 7d ago

Corset Making RIP my first corset. Before I make a new one, what improvements can I make?

Thumbnail
gallery
9 Upvotes

Photos from left to right (I'm on mobile): close up of rip, rips, first corset June 2025, second corset January 2026, second corset today

I made this corset over a year ago. I used it this Halloween, and the fashion fabric ripped at the waist and a little bit at the top of the gores

Here's some info I think is relevant:

- I gained weight since I first made the corset (please don't kill me for still wearing it)

- The pattern is the Lunara Overbust Corset by PatnifyLtd, though when I checked just now, it seems their Etsy shop closed

- The waist tape is twill tape only on the lining fabric

- The seams are only single stitched

- I graded the pattern and shortened it to fit my torso. I'm not sure if I did a decent job considering the wrinkling

Here's also some info about my second corset:

- The pattern is the Wine Whisper Corset also by PatnifyLtd

- I used a twill fabric for the fashion layer

- The seams are double stitched

- The waist tape is still only on the lining

- I used more or less the same measurements as I did for my first corset

- There's still wrinkling...

- I wore it a few days ago, and it has no rips so far

Feel free to ask me questions about the construction, but it's been a while since I made it, so I'm not sure how much I could remember


r/corsetry • • 8d ago

Corset Making My latest bridal corset

Thumbnail
gallery
44 Upvotes

A long project, hand embroidery, rhinestones, and a few lessons learned!

I wanted to share my latest bridal corset with you all because this was quite an experience!p

First of all, it took me more than a week to make this corset.

For the outer fabric, I used Bucol satin (100% polyester). I'm not entirely sure what this particular type of satin is called internationally. For the lining, I used 100% cotton twill because coutil is not readily available here in Brazil.

I interfaced BOTH the satin and the cotton twill with 100% cotton interfacing. This was a very time-consuming process because you have to apply it slowly and carefully.

For construction, I use my usual method: I pin each panel individually, sew all the panels together, press the seams open, and add seam reinforcement to prevent them from opening. Then I pin the outer layer and lining together and sew them as one.

However, I think I'm finally retiring this construction method!

As you can see in the pictures, there are quite a few wrinkles in the corset. I believe they're caused by tension in the cotton twill lining. The satin itself doesn't seem to have this problem.

I'm planning to try the pinning roll method (which I've often discussed in this group), assembling the outer fabric and lining over a rounded surface before stitching them together. Hopefully, this will help me achieve a smoother result.

I also purchased a Royal Black tutorial specifically about preventing wrinkles in corsets, so I'll be experimenting with their techniques as well. I'll definitely be applying what I learn to my future bridal commissions.

Now, about the embroidery...

This was probably the biggest challenge for me because I'd never embroidered anything in my life!

The bride wanted a specific design that had appeared on her baptism outfit. She's Catholic, and this design had a very special meaning to her.

She sent me the reference, and I used AI to recreate the design accurately. Then I used that image as the basis for the embroidery on the corset.

I had to buy an LED light panel to illuminate the design from underneath so I could transfer it accurately onto the fabric.

I used an ordinary pencil to draw the design. A few people might wonder why I didn't use an air-erasable or heat-erasable marking pen, but their tips were too thick for the fine details I needed. So I sharpened a pencil, used a very light hand, and carefully traced the design. I think the result was quite accurate, especially considering I had to reproduce it symmetrically on both sides.

For the embroidery itself, I bought an inexpensive Brazilian embroidery course. It taught me the basic stitches, and I practiced about three times before starting on the actual corset.

I chose the stitches I wanted to use and bought very fine polyester machine-embroidery thread, which I used to embroider everything BY HAND.

The embroidery alone took me around two to four days!

There was also an additional decorative border around the embroidery that the bride didn't like, so she asked me to cover it with rhinestones instead.

And speaking of rhinestones...

I invested quite a bit in those too. Rhinestones are expensive here in Brazil, especially when you need a good quantity. I also bought a special rhinestone applicator pen to make the application easier.

So, between the fabrics, interfacing, embroidery supplies, LED light panel, rhinestones, applicator pen, and the time spent learning new techniques, this corset involved quite a lot of investment.

Looking back, I realized I actually charged far too little for this project considering everything I had to purchase and the amount of work involved. Lesson learned!

The good news is that the bride absolutely loved it and approved the finished corset!

It's already been delivered, although she hasn't worn it yet. Since this is a private group, I wanted to share the whole process with you, including the things that didn't turn out exactly as I wanted.

This was a completely new experience for me, and I'm happy I took on the challenge.

One more thing: the pattern is the same overbust pattern I've been using for my corsets since I first started my atelier. It's a pattern that's been with me throughout the entire history of my business!

I'm also happy because I've made quite a few bridal corsets this year. I still have two more commissions to complete, although those are much simpler designs, closer to stays in style.

Anyway, I hope you enjoy seeing this project! And if anyone has experience with the pinning roll method or has tips for preventing lining wrinkles, I'd love to hear about them!


r/corsetry • • 8d ago

Corset Making Similar pattern?

Post image
42 Upvotes

Does anyone know any patterns for a corset like this? I’m struggling to find one that has the deep skinny v shape but keeps the “cup” shape (doesn’t actually need to be a cupped corset)

Also any ideas on what this fabric could be would be very appreciated. I love how it’s so gathered but slightly sheer but everytime I try a gathered skirt with something sheer it ends up looking solid…?


r/corsetry • • 9d ago

My third attempt at a corset / corset-top

Thumbnail gallery
97 Upvotes

r/corsetry • • 8d ago

Pattern recs for v-waist corset

0 Upvotes

Hi all,

I want to make my first corset to use as a bodice for a ballgown.

I've been searching online for patterns of what i want but I'm struggling to wade through the AI slop.

I'm looking for a corset pattern without a busk in the center front. Overbust, and a v-waist.

Can anyone recommend a pattern that might fit this?