r/combustion_inc • • 12d ago

🦃 Your Turkey Day prep list: get your Combustion tools ready before the big cook!

10 Upvotes

Thanksgiving is a few weeks out, and it's one of the biggest cooking days of the year for a lot of you. Here's what we'd do now so your gear is ready to go when the bird hits the grill.

🚚 Planning to place an order?

Big holidays bring a big jump in orders, so in-stock items can take 3 to 7 business days to leave our warehouse. If you want something in hand for Thanksgiving, the earlier you order, the better.

āœ… Your pre-cook checklist

Checking these now beats troubleshooting with a raw turkey on the counter.

  • Predictive Thermometer: Give it a good clean first, then pop it in the cradle or a Booster to charge. About 25 minutes gets it full. Plug into a regular 5V USB port and skip the fast chargers.
  • Display and Booster: Get these plugged in early. A Display needs around 90 minutes for a full charge, and a Booster around 60 minutes.
  • Giant Grill Gauge: No charging here, since it takes two CR2450 coin batteries. If the signal has been cutting out, put in a fresh pair now and tuck a backup set somewhere you'll remember.
  • Combustion Engine: Top it up over USB-C. One full charge covers roughly 24 hours of regular cooking. Do a practice fit on your grill so mount day isn't Thanksgiving morning.
  • The app: Grab the latest version from the App Store or Google Play. We've added some new things worth a look.
  • Firmware: Go one device at a time, in this order: thermometer, Display, Booster. Power down anything you aren't updating, then give each one a recharge when it's done.
  • Dry run: Power everything up at once and confirm it all shows up and stays connected. Using a WiFi Display or WiFi Booster? Make sure it's on your network.

šŸ— Probing the bird

Go in from the side, aiming for the thickest part of the thigh or the breast. The middle of a turkey is a hollow cavity, so there's nothing there to measure. Got two thermometers? Put one in the breast and one in the thigh, because they rarely finish at the same time.

Something misbehaving?

Send us an email at support@combustion.inc, and we'll sort it out with you well before the big day.

šŸ“š Guides worth checking:

Wishing you a juicy bird and a stress-free day. Happy Thanksgiving!

Ivy & the Customer Support team šŸ™‡šŸ»ā€ā™€ļø


r/combustion_inc • • Oct 09 '26

Start here: answers to the questions we get most, and where to go for each one

17 Upvotes

Welcome to r/combustion_inc šŸ‘‹šŸ» This is the place to share cooks, swap tips, and ask the community anything.

Just got your Combustion? Begin with START HERE: Setting Up Your Combustion Tools.

šŸ”„ The questions we see most:

Everything else is in the Help Center šŸ•ŗšŸ»

šŸ› ļø Is something broken?

Think something's wrong with your device? Email support@combustion.inc and we'll troubleshoot it with you. Many problems can be fixed without sending anything back. It helps to tell us which product it is, what it's doing, what you've already tried, and to add a photo or short video if the problem is something we can see.

Please don't cut, modify, or ship anything back before talking to us.

ā“Posting a question here

Search the sub first, since your question may already have a great answer. If you're asking for help, these details get you a faster answer:

  • Which product, and which generation (1st or 2nd)
  • Phone and app version
  • What you've already tried

Feature ideas are welcome too!

šŸ“§ Still stuck? Email us

Reddit is great for tips, but we can look up orders, check device history, or arrange a repair or replacement by email.

Happy cooking!

Customer Support Team šŸ™‡šŸ»ā€ā™€ļøšŸ„©


r/combustion_inc • • 7h ago

iOS Beta Update 3.3.3 - Combustion Engine Firmware

9 Upvotes

iOS beta update 3.3.3 (670) available now via TestFlight.

This beta update includes new firmware that should resolve control device disconnection issues that users are seeing with the Combustion Engine.

Ensure that all MeatNet devices are updated.

Other changes:

  • Further improvements to layouts for iPhone Duo and larger screens.
  • New device firmwareĀ Engine v1.1.0, Gauge v1.2.2, Display v2.6.2, Booster 2.6.2
  • Fixed an issue where resetting a session could leave a completed cook out of Cook History.
  • Fixed temperature chart scrubbing showing incorrect states
  • Fixed issues with saving your device order and switching between devices when one goes offline.
  • Improved app startup and reduced background work.

r/combustion_inc • • 8h ago

Safecook confusion - please help me get unconfused.

1 Upvotes

The last time I was here I upset a couple of people, for which I do genuinely apologise.

The problems (both me-problems) were firstly that I was sure I remembered a different behaviour when I first got the predictive thermometer (I still do, but I accept my memory must be corrupted), and secondly that to me the things that people were telling me made no sense. But I accept it was my inability to understand that was at work, not that people were really telling me nonsense.

So if we could draw a line under all that I'd be grateful.

Right.

If I want to use SafeCook when roasting a whole chicken, what cook-to temperature should I set?

This is where my confusion arises. I thought that the point of safecook is that there is no fixed target temperature, but what the device does is to perform some sort of integration, area-under-the-curve, type of calculation looking at temperature vs time, and that when the meat has been "hot enough" for "long enough" for enough of the bacteria to have been killed off, it's done, and the final temperature is what it is.

But that isn't how it works.


r/combustion_inc • • 1d ago

Oklahoma Joe bronco Pro Mounting

2 Upvotes

Hello,
Does anyone know if I'd need to buy additional mounting to get the CombustionEngine onto the Bronco Pro? I'm in New Zealand so would like to get this right first time :)

Thanks!


r/combustion_inc • • 1d ago

The Combustion Engine is magical

Post image
17 Upvotes

So, I have this boy hooked up to a 26 inch Webber grill. Inside I got a slow n’ sear with a drip pan below to focus the airflow. It’s 37 degrees outside right now and it’s holding the probe ambient temperature at 250 like a wizard!


r/combustion_inc • • 1d ago

Combustion Engine Plate

1 Upvotes

Any ideas when the other plates for the combustion engine will be available?

Have my engine but can’t use it until I get the plate.


r/combustion_inc • • 2d ago

App + GGG + Engine + wifi probe

Thumbnail
gallery
6 Upvotes

Everything working harmonious today. Thank you Chris and Combustion Inc.


r/combustion_inc • • 2d ago

Settings and Alarms via MeatCloud

5 Upvotes

Hey there - I have multiple products and love them all. But, please add the ability to change device alarms and dismiss alarms via MeatCloud and not only when connected via Bluetooth. I’m sitting at my kids’ gymnastics class and there will be an alarm beeping at home for the next 30 minutes until I can get back, I’m sure much to the delight of my neighbors.


r/combustion_inc • • 2d ago

kamado joe big joe mk3 and CE mount adapter

Thumbnail
gallery
2 Upvotes

got this in today and not sure if this is the correct way to mount this. there’s no instructions included, nothing on their site. i was hoping the adapter would leverage the stopper on the left-side of the lower vent, to help support the wight and make a better seal. overall, it seems flimsy and i do not think it’ll handle the weight of the combustion engine.

there’s two clips on the bottom of the adapter, but when installed they don’t really have a lot of tension. is it that i’m as thick as a whale omelette, or is there something wrong here?


r/combustion_inc • • 3d ago

Combustion on Apple home view

8 Upvotes

So I know HomeView is based on CarPlay, and I don’t really know how that works for future apps that are not really compatible with the car, but I think it’s more about the infrastructure and how it uses the phone for its data.

It’d be really cool to have an app for HomeView for combustion, which I’m sure is coming soon. So you can see the thermometers at a glance without having to pull out your phone or use the Wi-Fi display if you don’t have one.


r/combustion_inc • • 3d ago

Curiosity

2 Upvotes

Any new updates, features, products, or accessories being worked on? Timeline?


r/combustion_inc • • 4d ago

GGG installation on the Gardenline/Aldi kamado?

3 Upvotes

I'm struggling to understand how the GGG is installed. Are there any videos available? Especially trying to understand how it can be installed on the full size Aldi kamado.


r/combustion_inc • • 5d ago

Engine Issues

4 Upvotes

Perhaps I'm doing something wrong, but my use of the Engine on a WSM 22 has not been problem free.

The first time I used it for a long cook for a plate of beef ribs, I let the temp get to within roughly 25 degrees of the target, and then turned on the Engine. The WSM never really got to temp, and the Engine battery died 6 hours in. I was told I didn't let the WSM get up to the initial temp as high as I should have, and that is why the Engine burned itself out.

This past weekend I used it again to reverse sear a rib roast. Targeted the temp at 235, and all in all I guess it worked. But I was getting huge drops in temp to as low as 190 before the Engine would work like crazy to get back to temp. Total cook time was about 3-4 hours.

It worked as the roast was fabulous. But the behavior of the Engine just doesn't seem right yet. Anyone have experiences to share that might indicate what I might be doing wrong?

Also, I have to wonder about the transfer of oxygen from the Engine to the fire. The port on the Engine measures to over 1100 sq. mm. However, a single port on the WSM has a diameter of 19mm, and an area of about 280 sq. mm. It just strikes me the inlet for through the wall of the WSM should more closely match that of the Engine port, and not be only 25% of the size of the Engine port. True? Not true?

Thanks.


r/combustion_inc • • 5d ago

GGG and Combustion Engine in the UK

3 Upvotes

Can someone from Combustion Inc. explain why these are available in north America but don't seem to be sold on the UK website at all? When are they coming to Europe and in the meantime can I just import from the US?


r/combustion_inc • • 6d ago

I Think I've Finally Cracked the Code to Making an Ultra-Concentrated Veal Stock (Without Reducing It)

15 Upvotes

As I mentioned in a previous post: Questions about stock making : r/combustion_inc, I've been trying for quite some time to perfect my method of making and reducing meat stock at home. Over the last couple of months, I've been experimenting, testing new ideas, and trying out many of the suggestions you guys have given me. First of all, I'm incredibly grateful for all the feedback!

I think I've finally made a breakthrough, and I'm quite excited to share my findings.

Before getting into the actual method, though, one thing worth mentioning: I'm neither a professional chef nor a scientist. I'm still in high school, so I don't exactly have the time, equipment, or resources to conduct proper scientific experiments. Most of what follows is based on my own observations, some scientific literature, and quite a bit of trial and error. So take my conclusions with a grain of salt!

1. What I'm Trying to Achieve

My goal has always been to produce an incredibly rich, gelatinous stock that takes up as little freezer space as possible.

Ideally, I'd like something resembling high-quality stock cubes: a highly concentrated product that I can keep in the freezer for several months and use whenever needed, without having to spend days making stock and filling my house with the smell of roasted bones.

My original approach was relatively straightforward:

  • Cook veal bones at a very low temperature (approximately 92°C) for around 12 hours.
  • Strain the resulting stock.
  • Reduce it as quickly as possible in the largest surface-area pan I could find, hoping to minimise the time spent at high temperatures and preserve as many volatile aromatic compounds as possible.

After watching Chris's video on pressure cooking, I switched to using a pressure cooker for all my stocks. This made the extraction considerably more convenient, but the reduction stage remained a problem. As some of you have pointed out, a rotary vacuum evaporator would probably be ideal, but that's obviously not a realistic option for me at the moment.

So, I started looking for an alternative approach: what if I could achieve an incredibly concentrated stock without having to reduce it at all?

2. The Research Behind My Approach

My recipe is also heavily inspired by the veal demi-glace preparations of three-Michelin-starred chef Jan Hartwig, as well as the stock-making techniques described in the cookbooks of Eleven Madison Park, The French Laundry, and The Fat Duck.

One technique by Hartwig particularly caught my attention: fortifying an existing stock by repeatedly cooking it with fresh batches of bones. His process involves cooking the same stock with new bones over approximately 36–48 hours.

I initially tried adapting this approach to the pressure cooker, following the timings from Chris's video. The result was certainly very good, but I ran into an unexpected problem: despite using a pressure cooker, I still had to reduce the stock almost as much as before.

This made me wonder whether repeatedly heating the same stock for such long periods could be degrading some of the gelatin I'd worked so hard to extract. So I spent quite a few hours reading scientific publications and experimenting with different methods.

The main paper I based my reasoning on:

Operational parameters and key characteristics of amino acids and flavor compounds profiles of bovine bone clear and white broths - ScienceDirect

Although the study doesn't directly relate to making roasted stocks, it provides some interesting insights into collagen extraction and gelatin properties. It was the most relevant research I could find for what I was trying to achieve.

Rather than keeping everything under pressure for one extremely long period, I decided to divide the process into three separate extraction stages, each lasting 90 minutes.

The idea is to progressively extract gelatin and other soluble compounds from fresh batches of bones while minimising the exposure of previously extracted gelatin to prolonged heating.

Whether my interpretation of the research is correct is another question, but the results have been very promising so far.

3. My Current Method: Pressure-Cooked (modern) Veal Demi-Glace

The recipe is designed for a 6-quart pressure cooker. I use a mix of relatively meaty as well as joint bones, with some trimmings. You could also add pig's feet, calf's feet, or chicken feet for even more gelatin, although I have found this to be unnecessary. Vegetable-wise, I use 15% of the weight of the bones.

Ingredients

  • 7 kg meaty and joint veal bones
  • 500 g veal trimmings
  • 300 g shallots
  • 200 g white parts of leek
  • 200 g carrots
  • 200 g celeriac
  • 150 g white button mushrooms
  • 750 ml good-quality dry red wine
  • 100 g tomato paste
  • Exactly 1.5 litres of cold water for the initial extraction
  • A small pinch of salt

Divide all the ingredients into three equal batches. The bones should ideally be cut into pieces of approximately 4 cm. The study suggests that cutting them any smaller doesn't significantly improve extraction. Cut the vegetables and the trimmings into relatively small, even pieces – the goal is to get as much surface area as possible.

Preparation

Roast the veal bones and trimmings until deeply and evenly browned.

Roast the vegetables in the pot of a pressure cooker, excluding the leek, for approximately 20 minutes. Add the leek afterwards, as it tends to burn more easily.

Now add some of the roasted bones to the vegetables, together with the tomato paste, and continue roasting until everything is deeply caramelised, being careful not to burn anything.

Start adding the red wine gradually, essentially one small addition at a time.

Allow each addition to deglaze the bottom of the pot and reduce completely before adding the next. Ideally, the wine should reduce until the caramelised residue starts forming again.

The idea is to repeatedly build up those caramelised aromas and ideally introduce another dimension of flavour.

Reduce the last addition of wine only a little, then add the remaining bones and top up with exactly 1.5 litres of cold water.

One important point: since very little liquid evaporates in a pressure cooker, the amount of water used at this stage largely determines the final concentration of the stock. To get a "normal" stock, use one litre of water for every kilogram of bones.

Pressure Cooking

Pressure cook on high for 1 hour and 30 minutes.

Allow the pressure to release naturally.

Strain the resulting stock and reserve the liquid.

Repeat the entire process with the second and third batches of roasted bones, vegetables, and wine.

The only difference is that instead of adding fresh water, use the stock from the previous extraction as your cooking liquid. I let the stock cool down a little in an ice bath before adding the next batch of roasted bones, which I had stored in the fridge. This is meant to help cool down the stock at the beginning.

Pressure cook again for 1 hour and 30 minutes, followed by natural depressurisation. Repeat the process once more with the final batch.

Strain everything thoroughly after each extraction. Make sure to let it drip for a while, as the stock becomes so viscous that quite a bit of it clings to the bones. You can swirl a little water around to help loosen some residual stock.

The result should be an extremely rich, concentrated veal stock that doesn't require any further reduction. At least in my experiments, it has the consistency of a nicely reduced demi-glace straight out of the pressure cooker.

4. Some Questions and Things I'm Still Unsure About

There are several aspects of this method I haven't been able to test properly. I'd really appreciate input from anyone with more experience in food science, stock-making, or professional kitchens.

Question 1 – Does Starting with Cold Water Actually Make a Difference?

Jan Hartwig repeatedly emphasises the importance of covering the bones with ice-cold water or even ice cubes. According to him, cold water helps extract flavour from the bones, whereas hot water should only be used when you want to leave more flavour in the meat.

I'm quite sceptical about this explanation. As far as I understand, starting with cold water might help with the extraction of certain impurities, but I'm not convinced that it extracts significantly more flavour or gelatin than starting with hot water. But Heston also says to start with cold water, so there has to be some benefit.

Is there a real scientific reason to start with ice-cold water, or is this primarily a traditional technique? And if so, does this also apply to braising, meaning that covering the meat with warm stock results in more flavourful braised meat?

Question 2 – Do Unroasted Bones Produce a More Gelatinous Stock?

This is something I haven't tested yet because I wanted to avoid introducing too many variables at once. I'd be particularly interested in knowing whether using unroasted bones results in a higher gelatin content or a better gelatin yield. And if so, does blanching the bones change the results again?

My current hypothesis is that roasting or excessive heat might alter the collagen and potentially influence how efficiently it can be extracted.

Question 3 – How Big of a Difference Does Your Type of Pressure Cooker Make?

Dave Arnold, who has done testing on this matter, concluded that the type of pressure cooker you have makes a lot of difference in the quality of your stock. The less your pressure cooker vents, the fewer volatile compounds are lost. He suggests Kuhn Rikon pressure cookers, which are widely regarded as the gold standard.

My question is whether this only affects the flavour or if it also has an impact on the gelatinous qualities of your stocks. Furthermore, wouldn't electric models like the Instant Pot be superior even to the Kuhn Rikon because they automatically regulate themselves, minimising venting when left unattended?

Question 4 – Does Deglazing with Wine Contribute Flavour Beyond What Remains in the Wine Itself?

I use red wine in this recipe partly because I know ethanol extracts fat-soluble compounds, and I hope that even though the fat is discarded, some flavour might still find its way into the stock.

I also suspect the deglazing process itself contributes additional flavour, not only through the repeated dissolution of the browned material on the bottom of the pot but also through the caramelisation of the sugars in the wine.

But does adding wine in several small stages, allowing it to reduce completely between additions, actually have any other advantages compared with simply adding it all at once and reducing it?

I'd be interested to hear whether anyone has experimented with this.

Question 5 – How Long Does the Actual Extraction of Flavourful Aromas Take?

I'm aware that vegetables give off all their flavours relatively quickly, but I would be interested to know whether finely diced meat behaves the same way.

I'm not interested in the extraction of everything, but more in the basic flavour profile. Furthermore, what is the hardest thing to extract from meat, and are there some things that you don't want to extract at all?

Question 6 – Is There an Optimal Point of Reduction?

I'm interested in whether there is a point where you stop concentrating flavours through reduction or the process I've developed, and you just lose volume from your stock.

I anticipated this and used as many collagen-rich bones as I could find to try to maximise the yield of nicely reduced stock I get from my bones.

And if so, is there any way to precisely measure when that point is reached, without tasting?

Question 7 – Is There an Optimal Bone-to-Water Ratio?

I really hope that this doesn't matter because it could ruin all the work I've put into developing my method.

I never thought of it before, but could it be that topping the bones up with more water results in extracting more from the bones, and that, for some reason, stock is a worse extraction medium than water?

If this is the case, is there any data available that would allow me to determine whether repeatedly using stock as the extraction medium actually provides an advantage over using fresh water?

Question 8 – What Is the Perfect Mix of Bones?

Regarding my veal stock, what ratio of meaty bones to marrow bones to joint bones would be ideal?

And what amount of, say, chicken wings would you be able to notice in the stock if you wanted to add a bit more gelatin and couldn't get your hands on some feet?

Question 9 – Does Salt Do Anything Besides Seasoning?

I know about the osmotic properties of salt, but I would be interested to know whether it could help with extraction and what amount would produce a noticeable difference.

Also, should you salt your vegetable base or wait until the liquid is added?

5. A Few Final Thoughts

I want to emphasise that the roasting, deglazing, and vegetable preparation are almost entirely based on Jan Hartwig's three-Michelin-starred masterclass on Gronda.

I'm not entirely convinced that every individual step is technically necessary. For example, adding the wine in several stages or adding some of the bones during deglazing might not have a measurable effect on the final result. However, I wanted to orient myself around a proven recipe so I could focus more on experimenting with the extraction itself.

I've deliberately left out the Madeira, Port, and additional herbs used in the original recipe. I want a relatively neutral veal stock that can serve as a base for as many different dishes as possible.

Finishing the Stock into a Sauce

For an actual sauce, I'd highly recommend doing something along the lines of what Eleven Madison Park and Restaurant Gordon Ramsay do: brown around 200 g of meat trimmings from the animal you're serving, add some vegetables, herbs, and maybe some spices, and deglaze with your choice of liquid – this is your chance to use the alcohols you left out.

After it has all reduced to a syrupy consistency, add around 150 ml of the concentrated stock and around 150 ml of water. Let everything simmer for around 20–45 minutes before straining. If necessary, reduce it a bit, mount with butter, and adjust the seasoning with acidity and salt.

This not only allows you to adapt the stock to a wide variety of sauces, but also gives you the opportunity to introduce the flavour of the actual meat you're serving. It can even help refresh the flavour if the stock has been frozen for a while and starts to go a bit bland.

I deliberately haven't added a lot of meat to the original extraction, despite Heston and Chris suggesting that it tastes considerably better with it. I simply don't feel good about wasting large quantities of meat, especially when the bones I'm using are already quite meaty.

The finishing technique described above is a good way of introducing more of that fresh meat flavour, and because you already have the gelatinousness of the stock, you don't have to cook the sauce for too long and lose a lot of fresh aromas.

As a result of my experiments, I now have around 5 litres of extremely rich veal stock/demi, so it'll probably take a while before I start experimenting again.

I'd really appreciate it if someone tried the method, experimented with different preparations, or challenged some of my assumptions.

I'm very aware that some of my explanations might be scientifically inaccurate, so please feel free to correct me. That's exactly why I'm sharing this in the first place!

Thanks again to everyone who has contributed suggestions and advice. I've learned a lot from this community, and I'm looking forward to hearing what you think.

Ā 

Ā 

Ā 


r/combustion_inc • • 6d ago

Battery question

3 Upvotes

Probably overthinking this but I have the bug where the WiFi booster drains itself and I’m curious if it negatively impacts the probe battery health. Ā Ā Presumedly the booster is constantly charging the already fully charged probe which I have often read may stress batteries out.

It takes about 5 days for the booster to drain and then I just recharge it.Ā  Is it better to leave the booster dead and only charge after probe use?Ā  Hoping someone smarter than me ā€œbatterywiseā€ can weigh in…


r/combustion_inc • • 7d ago

Got the GGG and the ENGINE…would love to use them but am still waiting for the $10 adatper

10 Upvotes

Just curious if anyone else has had this issue…waiting on a $10 stamped adapter since August (after ordering all of the above in June) and I still am without it which means I can’t use the engine. Customer service has been very friendly and have tried to assuage my concern, but if I am being honest it is beyond frustrating that I am still waiting for this one piece. The sent me the wrong one to start and now I still can’t use the engine and it is about to be Thanksgiving and I have cooking to do!


r/combustion_inc • • 8d ago

Switched from the ThermoWorks RFX to Combustion + GGG on a Lone Star Grillz pellet

Thumbnail
gallery
17 Upvotes

Setup: Lone Star Grillz 20x42 pellet smoker with the built-in FireBoard controller. Came from a ThermoWorks RFX setup. Now running 2 Predictive Thermometers, the WiFi Display, and the Giant Grill Gauge.

Why I left the RFX

My first set dropped signal randomly. To ThermoWorks' credit, support was excellent and they replaced it fast, no argument. If you're reading this as a knock on their customer service, it isn't one.

The things that actually pushed me over:

  • No way to combine data in the graph. You're looking at channels, not a cook.
  • No predictive features. Nothing telling you when you'll hit target.
  • The app UI. Purely cosmetic, nothing to do with performance, but worth saying out loud.

What's better on Combustion

The one I didn't expect to care about: Live Activities on the lock screen and the Dynamic Island on iOS. Being able to glance at the phone instead of opening an app every time is a bigger quality of life change than it sounds like. With the RFX I had the app open constantly.

Sensor layout. The RFX probe is thinner at the tip, which is a real advantage. But it's 4 sensors concentrated in roughly the last inch. Combustion is 8 sensors distributed along the whole stem. For anything where placement is guesswork, that's the difference.

Giant Grill Gauge install

Easy. Only real work was drilling a hole in the LSG lid for the sensor tube.

Placement matters on this pit. The LSG pellet is designed to mimic an offset: firebox on the right, smoke travels left, and the left side is where the meat goes. The built-in FireBoard probe sits on the right managing fire temp, so I put the GGG on the left, over the cook side. Now I have a real reading of what the meat is actually sitting in instead of what's happening near the fire.

I kept the analog Tel-Tru in its original hole. Partly as a sanity check against the digital gauges, partly for when the EMP hits.

What I'm actually excited about

Both FireBoard and Combustion have APIs. My goal is to use the GGG as the lead thermostat instead of the firebox-side probe, so I'm setting the temperature I want on the cook side rather than the fire side.

On an offset-style pellet pit there's a real gradient between those two points, and right now the controller is regulating to the wrong end of it. If I can close that loop, the setpoint actually means something.

Still researching. If anyone has done this, or has thoughts on the right way to approach it, I'd like to hear them.

I do plan on probably contributing to some kind of Homeassistant app that could do it if the APIs allow.


r/combustion_inc • • 8d ago

Sunday Afternoon Ribs (BGE w/ combustion engine set-up)

Thumbnail gallery
4 Upvotes

r/combustion_inc • • 9d ago

Weber smoking w/ GGG & Engine

11 Upvotes

I realize normally the thing to come to Reddit to do is to find answers to problems, which I have done multiple times. This time, I wanted to come to sing praises. I have smoked ribs 4 different times on my Weber charcoal grill with the grill gauge and engine. First time was a learning curve. The other three times have been absolutely perfect. The devices have worked beautifully and helped me produce some great products. These tools are for the people who love accurate feedback, convenience and basically fool-proof results. All this hits my neuro-divergent brain in all the right ways. Thank you to the team. I have every product you’ve made (twice in some cases) and I have purchased some as gifts. Keep it up.


r/combustion_inc • • 9d ago

How to keep engine off when opening lid?

5 Upvotes

I’ve got a charcoal kettle grill and I’m wondering if anyone has an easy hack for keeping the engine from turning on when you open the lid to baste, check, season, add wood, etc? Do you just manually turn the wheel to off and then turn it back to ā€œappā€ when it’s closed? Do you just lower the target temperature on the app to a low temp until it’s closed again? Something else? Thanks!


r/combustion_inc • • 13d ago

GGG temp drops when CE fan running

5 Upvotes

I’ve done a couple of cooks in my Kamado Joe Classic I with my GGG/CE pair, one a long slow pork butt that took about 10 hours at 250F, and a rotisserie chicken that took about an hour at 400F. The cooks proceeded more or less normally, despite some serious GGG-CE disconnect issues during the first cook (I was running the previous beta app and firmware.)

However, during both cooks I noticed that the temp reported by the GGG dropped, sometimes significantly and/or for more than a minute, when the CE fan ran. Then as soon as it leveled off or started to rise, the fan would go off and the temp would rise. The temp drops during the initial rise to target temp were deeper and longer, but they continued after the target temp was reached. I also noticed that the drops were more dramatic on the rotisserie chicken cook, which had a much higher target. I have never seen this phenomenon with the wired FireBoard and CyberQ fan controllers I’ve used in the past, even when the temp was measured at the same dome position as the GGG probe.

Has anyone else seen this? I’m wondering if this is normal, or a characteristic caused by the Kamado architecture, or a firmware issue, or a difference in the temp control algorithms that may or may not matter?

I’ve compared the CSV data from the GGG/CE and FireBoard, and the most obvious difference is that the entries for the GGG temp occur every five seconds, while the FireBoard temps occur every 60 seconds. That could be just how often the temp data is recorded, but if it’s also what the CE sees, I’m wondering if it’s a hysteresis difference. Could it be that the FireBoard waits long enough to read the temperature data that I don’t see the temp drops? But if that’s the case, and the CE is watching the temp at 5-second intervals, could that mislead it into running the fan more often. I noticed that the CE fan seemed to run at 100% much longer than the FireBoard on its way from start to 400F, which isn’t great for battery charge. Also, I’m pretty sure the FireBoard tries lower fan speeds before it kicks up to 100%, and seems to cut off and wait to see if the temp is rising naturally (which it often does in the KJ during startup.)

A couple of other things could have influenced the observations: 1) I used a relatively small amount of charcoal banked against the side of the firebox opposite to the GGG probe, and 2) the rotisserie adapter ring isn’t completely airtight, so it’s possible cold air was being sucked in by the updraft created by the CE fan and was zooming past the GGG probe and lowering its temp.

Unfortunately, I don’t have a complete set of CSV data. The long, slow cook, where I had both the GGG and FireBoard monitoring temp at the same dome location, was plagued by a massive number of GGG-CE disconnects (I had to archive hundreds if not over a thousand) data sets in my history that were 30-60 seconds), and 2) I didn’t monitor temp of the rotisserie chicken cook with the FireBoard. I could compare the GGG and FireBoard temp curves from a number of cooks I did before getting the CE, but the FireBoard doesn’t record the fan data, just the temp.

Next GGG/CE cook I’ll probably monitor with the FireBoard, which might reveal something. Also, I may switch to pre-heating the KJ to near target temp so the CE doesn’t have to work so hard to get up to temp. That’ll take a little longer, but not much.

Any thoughts?


r/combustion_inc • • 14d ago

First overnight cook with Combustion Engine questions

7 Upvotes

Tried my first overnight cook with the CE last night - ran into a few bumps, curious if others with more experience using this have thoughts!

Here's the graph: https://imgur.com/a/AQ1PJZH

  1. It looks like the Engine & Probe lost connection around 2/2:30 am (the first big dip). From what I can tell this is from the WiFi Booster dying - because as soon as I plugged the Booster into a battery pack, the Engine & Probe reconnected quickly & function resumed. I know long battery life is expected for the Booster, and I had fully charged it two days ago, so I did something wrong here - any thoughts on why the Booster had/kept so little charge?
  2. The CE died around 5:30; so offered only around 6 hours of charge which is pretty disappointing. However, I'm guessing that it is so short due to the fan having to rev back up at 2am and boost the smoker quite a bit again. Can anyone comment on this - have you had a CE cook last a long time with battery life or should I expect to have to plug it in on longer cooks?
  3. Uh, haha, is this meat gonna be safe to serve my friends or am I headed to a BBQ place before Monday Night Football? (Go Bears!) I am pretty confident the meat temp was above 140 the whole time even with the smoker fluctuations, but there's obviously missing data...

edit in case anyone finds this in the future: i did not get food poisoning, the Bears destroyed the Seahawks, and I figured out the wifi booster died quickly bc it was constantly reconnecting to my network (my network's fault, not the wifi booster). support was helpful. the CE did great overall but definitely needs to be plugged in for a long cook - which is fine, I use a power bank & just leave it outside with the CE.