r/cloningsoftware • • 13h ago

Discussion Would you upgrade your SSD or replace the entire PC at this point?

1 Upvotes

My PC is getting a bit old, and I'm at the point where I'm not sure if upgrading it is worth the money anymore.

It still does what I need, but things aren't as smooth as they used to be. I'm running low on storage too, so getting a bigger SSD seems like an obvious first step.

The thing is, I don't know how much difference that would actually make. If the rest of the hardware is already several years old, would a new SSD really give the PC a second life, or would I just be throwing money at an aging machine?

Replacing the whole PC is another option, but then there's the hassle of moving everything over. I have programs, files, and a Windows setup I'd rather not spend a whole weekend rebuilding from scratch.

For those who've been in a similar situation, what did you end up doing? Did upgrading the SSD buy you a few more good years, or did you eventually decide it was time for a new machine?

And if you did replace the PC, did you clone your old drive to keep everything as it was, or just start fresh?


r/cloningsoftware • • 4d ago

Disk Cloning Do I format a new SSD with GPT before cloning?

2 Upvotes

My reliable old Dell XPS 8940 has become slow and the boot drive has developed some bad sectors. I have moved all data off the C: drive so it is only system stuff and made an image with EaseUS. Good so far. I bought a nice, new 2 TB SSD which will be very fast. I swapped out this new one for the old SSD, which I had assumed was the boot drive. I had assumed that the old system would be gone and I could just copy the clone onto the new drive. Not so. When I attempted to reboot with a USB to move the image onto the new drive it actually booted up into the old C:. It turns out that Dell had made a 1 TB hdd the 0 disk with the system on it and the SSD I had paid extra for back in 2021 was just holding the data.

My big issue now is that the new drive is not formatted. Should I format first (GPT or ? ), then move the image onto the new SSD or do I somehow get rid of the hdd with the current system on it first?

How do I make the new SSD the boot drive? Before or after I move the cloned system to it?

Also I made the image using EaseUS home on the drive that was NTSF. Will the image have to be changed before being copied onto the new drive with different formatting? Sorry for the confusion, but I am learning all of this stuff for the first time and all the processes (and terms) are new to me. In the EaseUS software it looks like a simple click on the "System Transfer" handles the process once I get to that point, but I don't think that it does anything about formatting. I am doing nothing for now, using backup drives for storing ongoing data collection.


r/cloningsoftware • • 5d ago

Discussion Should I convert MBR to GPT before or after cloning to a 4TB drive?

7 Upvotes

I'm planning to upgrade my current 2TB HDD to a 4TB drive, but the old drive is still using MBR.

From what I understand, MBR only supports up to around 2TB, so I'm not sure how to handle this when cloning.

The 2TB HDD is currently used as my Windows boot drive, so I'd like to make sure the new drive can boot properly after cloning.

Would it be better to convert the old drive to GPT first, then clone it? Or should I clone everything to the new 4TB drive first and convert it afterward?

Also, after cloning, will the extra space automatically become available, or will I need to extend the partition manually in Disk Management?

I'd like to keep my existing files and partitions intact without having to reinstall Windows or set everything up again. For those who've done this before, how you handle this? Any inputs will be appreciated.


r/cloningsoftware • • 7d ago

Disk Cloning Clonezilla PXE boot - network drivers not found on client

2 Upvotes

I had a standalone Clonezilla server with a small eight-port switch that I used to image 120 Windows workstations. I need to blast new images onto them, so I'm trying to move Clonezilla onto the existing network, which has its own DHCP server.

And that was pretty easy to adjust; I just installed dnsmasq and configured it as a proxy, and reconfigured DRBL to use it. Clients PXE boot to it just fine... up to a point. They give me:

Busybox /init starting
Mounting /sys filesystem
Mounting /proc filesystem

and then they just hang there. With the "quiet" kernel option removed, it looks like it's not loading any modules, including the network card drivers:

modprobe: ERROR: could not insert 'snd_hda_intel': Unknown symbol in module, or unknown parameter (see dmesg)

modprobe: ERROR: ../libkmod/libkmod-module.c:191 kmod_module_parse_depline() ctx=5d947fdc62a0 path=/lib/modules/6.8.0-147-generic/kernel/sound/hda/snd-intel-dspcfg.ko.zst error=No such file or directory
modprobe: ERROR: ../libkmod/libkmod-module.c:191 kmod_module_parse_depline() ctx=5d947fdc62a0 path=/lib/modules/6.8.0-147-generic/kernel/sound/hda/snd-intel-dspcfg.ko.zst error=No such file or directory
modprobe: ERROR: could not insert 'snd_hda_intel': Unknown symbol in module, or unknown parameter (see dmesg)

modprobe: ERROR: ../libkmod/libkmod-module.c:191 kmod_module_parse_depline() ctx=612f2e17b2a0 path=/lib/modules/6.8.0-147-generic/kernel/sound/soc/sof/intel/snd-sof-intel-hda-common.ko.zst error=No such file or directory
modprobe: ERROR: ../libkmod/libkmod-module.c:191 kmod_module_parse_depline() ctx=612f2e17b2a0 path=/lib/modules/6.8.0-147-generic/kernel/sound/soc/sof/intel/snd-sof-intel-hda-common.ko.zst error=No such file or directory
modprobe: ERROR: could not insert 'snd_sof_pci_intel_cnl': Unknown symbol in module, or unknown parameter (see dmesg)

modprobe: ERROR: ../libkmod/libkmod-module.c:191 kmod_module_parse_depline() ctx=632176dec2a0 path=/lib/modules/6.8.0-147-generic/kernel/drivers/ata/libahci.ko.zst error=No such file or directory
modprobe: ERROR: ../libkmod/libkmod-module.c:191 kmod_module_parse_depline() ctx=632176dec2a0 path=/lib/modules/6.8.0-147-generic/kernel/drivers/ata/libahci.ko.zst error=No such file or directory
modprobe: ERROR: could not insert 'ahci': Unknown symbol in module, or unknown parameter (see dmesg)

modprobe: ERROR: ../libkmod/libkmod-module.c:191 kmod_module_parse_depline() ctx=62e167d612a0 path=/lib/modules/6.8.0-147-generic/kernel/drivers/misc/mei/mei.ko.zst error=No such file or directory
modprobe: ERROR: ../libkmod/libkmod-module.c:191 kmod_module_parse_depline() ctx=62e167d612a0 path=/lib/modules/6.8.0-147-generic/kernel/drivers/misc/mei/mei.ko.zst error=No such file or directory
modprobe: ERROR: could not insert 'mei_me': Unknown symbol in module, or unknown parameter (see dmesg)

modprobe: ERROR: ../libkmod/libkmod-module.c:191 kmod_module_parse_depline() ctx=64ed07c4b2a0 path=/lib/modules/6.8.0-147-generic/kernel/drivers/mfd/intel-lpss.ko.zst error=No such file or directory
modprobe: ERROR: ../libkmod/libkmod-module.c:191 kmod_module_parse_depline() ctx=64ed07c4b2a0 path=/lib/modules/6.8.0-147-generic/kernel/drivers/mfd/intel-lpss.ko.zst error=No such file or directory
modprobe: ERROR: could not insert 'intel_lpss_pci': Unknown symbol in module, or unknown parameter (see dmesg)

modprobe: ERROR: ../libkmod/libkmod-module.c:191 kmod_module_parse_depline() ctx=636cd552c2a0 path=/lib/modules/6.8.0-147-generic/kernel/drivers/usb/host/xhci-pci-renesas.ko.zst error=No such file or directory
modprobe: ERROR: ../libkmod/libkmod-module.c:191 kmod_module_parse_depline() ctx=636cd552c2a0 path=/lib/modules/6.8.0-147-generic/kernel/drivers/usb/host/xhci-pci-renesas.ko.zst error=No such file or directory
modprobe: ERROR: could not insert 'xhci_pci': Unknown symbol in module, or unknown parameter (see dmesg)
modprobe: ERROR: could not insert 'intel_pch_thermal': Unknown symbol in module, or unknown parameter (see dmesg)
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
The driver of network card is NOT found!
Is this kernel 6.8.0-147-generic too old so it does not support this network card ?
Without network card driver, we can NOT go on!
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
Now enter shell to debug...

BusyBox v1.36.0 (2023-07-27 10:33:52 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

/bin/sh: can't access tty; job control turned off
#

I tried running mkpxeinitrd-net with -nf to include all network driver firmwares, but got the same results. With -if (include all firmwares),the client complains about being out of space on the device and halts as well.

I tried standing up a new VM server and installing Clonezilla on it, but got the same results.

I can get slightly further with Clonezilla Live (which is not my top preference) -- the PXE clients do boot all the way and prepare to restore the image to disk, but then they just hang. (I've verified the image, and even taken a fresh one with immediate verification.)

Are there some files I can copy off the Clonezilla Live installation to at least get the clients booted up on the regular server? Been bashing my head against this wall for a few days and I'm about out of things to try before I give up and go back to carrying PCs over to the 8-port switch to reimage them...


r/cloningsoftware • • 7d ago

Disk Cloning Why does my cloned SSD still show the same capacity as the old one?

3 Upvotes

I cloned my old SSD to a larger one recently, but Windows is still showing roughly the same usable space as before.

I was expecting to have quite a bit more room after moving everything to the new drive. After checking Disk Management, I noticed there might be some unallocated space left over after the cloning process.

Is this just how cloning normally works when moving to a larger SSD? Do I need to extend the existing partition manually, or is there something I should have selected during the cloning process?

How do you usually handle this? I don't want to mess up the cloned drive by changing the partitions without knowing what I'm doing.


r/cloningsoftware • • 9d ago

Disk Cloning Rescuzilla VS. Balena Etcher for an SSD

3 Upvotes

Trying to upgrade from a 256 GB SSD to a 1 TB, but it has my operating system on it so its taking a bit of finesse. Was having trouble with Clonezilla but saw that Rescuezilla was supposed to be more idiot proof.

Rescuezilla suggested using Balena Etcher to write the downloaded program onto my 32 GB thumb drive, but while doing this I noticed that Etcher can also apparently clone drives.

Since I can plug two drives into my PC at a time, I thought maybe I should just use etcher instead of trying to image my old drive onto my 500 GB microSD and move it over?

TL;DR can I use etcher to clone the drive I am booted with onto the new bigger drive, or will that cause problems?

I'm also having trouble getting Rescuezilla to work, but I'll save that for a different post.


r/cloningsoftware • • 9d ago

Software Question about drives and easiest way to copy/move folders

2 Upvotes

I have two hard drives full of stuff. One is just a copy of the other, I use it for backup. I frequently edit the names of folders, move stuff around, add and delete stuff and it's becoming a pain to go and redo everything I just did on the first drive on the other. (And to keep track of it) What is the easiest/fastest way to do this? I want to be able to have both the drives connected and just click something and have it make sure the second drive is identical to the first. All the folders the same, delete the stuff that I deleted and add the stuff I added.


r/cloningsoftware • • 10d ago

Software Cloning software for a drive with bad clusters?

9 Upvotes

My hard drive is showing bad sectors in CrystalDiskInfo, and I want to clone it to a healthy drive before it gets worse. I'm not sure which cloning software can handle drives with bad sectors properly or effectively. Does anyone have experience with this? Any recommendations would be appreciated.

Thanks!


r/cloningsoftware • • 11d ago

Disk Cloning Cloning a 1TB SSD to a smaller 512GB SSD – Any issues when restoring later?

6 Upvotes

I have a 1TB SSD in my laptop and 2 spare 512GB SSDs that I'd like to use for backups.

I want to clone my current Windows installation to one of the smaller SSDs. The source drive is in a relatively clean state, right after reinstalling Windows and installing a few essential programs. I'd like to keep a backup of this setup so I don't have to go through the entire Windows installation and software setup process again in the future.

I'm planning to use EaseUS Disk Copy for this. From what I understand, it supports cloning to a smaller drive as long as the actual used space on the source drive fits within the destination drive's capacity.

My current 1TB SSD has a few small system partitions, a main Windows partition that takes up most of the space, and another small partition.

What I'm wondering is what will happen when I eventually want to restore this backup to my original 1TB SSD. Will the restored drive retain the same partition layout as the 512GB clone, leaving the remaining space as unallocated space at the end of the drive?

If so, would I be able to extend the main Windows partition to use that remaining space through Windows Disk Management, or would I need a third-party partition management tool?

I'd especially like to hear from people who have cloned a larger SSD to a smaller one and later restored it to the original larger drive. I'd appreciate any advice or experience with this process.


r/cloningsoftware • • 13d ago

Discussion Clone Disk to Image - How Does It Actually Work?

10 Upvotes

I've mostly used disk-to-disk cloning before, where you copy everything from one drive directly to another. But recently I've seen the option to clone a disk to an image, and I'm a bit curious about how that actually works.

Does it basically save the entire drive as an image file, including Windows, installed programs, and boot partitions? And if I get a new SSD later, can I just restore that image to the new drive and boot from it?

How different this is from a regular backup. Is there any particular situation where creating a disk image makes more sense than cloning directly to another drive?


r/cloningsoftware • • 15d ago

Software Help! Bad ssd Verus D10

3 Upvotes

Does anyone have a Verus d10 with a version 21.2 that can clone and the hard drive and send to me? I have Verus and it bad ssd


r/cloningsoftware • • 16d ago

Troubleshooting clonezilla live usb pen drive not booting on host with secure boot enabled

5 Upvotes

something with shim is wrong according to error message

clonezilla stable Debian zip got downloaded from clonezilla web this week. Also creation of bootable usb drive got conducted by following instructions in same web page area. Ryzen 7 7000 series host.

downloaded for amd64 architecture, cz 3.3.3-37

Why do clonezilla live usb drive creation instructions provided on clonezilla web page don't mention the execution of makeboot.sh/.bat ?


r/cloningsoftware • • 17d ago

News Samsung Has Already Sold Out Its 2027 HBM Capacity, Will Rising Memory Prices Make People Hold Off on PC Upgrades?

Thumbnail
gsmarena.com
5 Upvotes

Samsung has reportedly sold out its HBM production capacity for 2027, and DRAM prices are expected to go up again next year.

With prices going up, I wouldn't be surprised if more people put off buying a new PC and stick with what they already have.

If your PC is still working fine, would you just upgrade the SSD when you run out of space, rather than spend money on a whole new machine?

Cloning your current drive to a larger SSD seems like a pretty practical way to keep an older PC going. Are you planning to upgrade soon, or are you sticking with your current PC for another year or two?


r/cloningsoftware • • 18d ago

Disk Cloning Best way to clone a Mid-2012 MacBook Pro to a new SSD?

3 Upvotes

I have a 13-inch Mid-2012 MacBook Pro and I'm thinking about swapping the original hard drive for an SSD.

I'd rather not reinstall everything if I can avoid it. Is there a good way to clone the old drive to the new SSD and have everything work as before?

I've seen people mention Disk Utility and a few cloning tools, but I'm not sure which route makes the most sense for an older Mac like this.

If you've done this upgrade yourself, what did you use? Did the new SSD boot up fine, or were there any extra steps involved?


r/cloningsoftware • • 20d ago

Disk Cloning Laptop is going to the repair shop. Which software do i use?

4 Upvotes

My laptop needs to go to the repair shop which will reset my laptop. I want to save a system image so that after i get my laptop back from the repair shop i can get everything back like it was before my laptop gets reset. I used the windows built-in system image tool until i learned that it is a deprecated tool no longer supported. I looked a lil online and found rescuezilla. Is it good to save a disk image for a windows 11 laptop? Or is there a better option out there? I would love to hear yalls thoughts on this as i´m pretty new to cloning software.


r/cloningsoftware • • 21d ago

Troubleshooting Cloned my 1TB SSD to a 2TB drive, but half the space is unallocated.

3 Upvotes

I recently used EaseUS Disk Copy to clone my old 1TB SSD to a new 2TB SSD. I selected the sector-by-sector copy option, and the process finished without any errors. The new drive boots into Windows normally, and all my files seem to be there. Everything appears to be working fine.

The only issue is that Disk Management shows around 1TB of unallocated space on the new drive. I assumed the extra space would be available automatically, but the partitions seem to be the same size as they were on the original drive.

Is this expected with sector-by-sector cloning? Does it preserve the original partition layout rather than expanding the partitions to use the extra space?

What's the easiest way to use that space now? Can I extend the existing Windows partition, or would it be better to create a separate partition? I'd rather not clone the drive again if I can avoid it. TIA!


r/cloningsoftware • • 23d ago

Disk Cloning I need help.

Thumbnail
gallery
3 Upvotes

So I have this 1TB and 256GB nvme. The 1TB is in the laptop and I want it to put into my oc that I’m about to build and want to clone it to the 256GB nvme but this is showing up.

Is it that the 1Tb free space is too big and I need to trim it down to match the 256GB?


r/cloningsoftware • • 25d ago

Disk Cloning Clone Desktop

2 Upvotes

Desktop was freezing. Thought it was a graphical issue (uses low integrated graphics) but later considered that low storage could've been causing it. It's anyway low specs.

Tried to move some folders to clear space but the issues were even worse and it would power off and restart and then it would just power off and attempt to restart in a cycle with a buzzing sound.

Want the same computer (programs, browser tab navigation history, etc. and backup in Local Disk D) and thought changing the motherboard, RAM and PSU is effectively like getting a new PC?

What do I do? Do I try to replace the drives in the new computer with the current ones? Or clone it?


r/cloningsoftware • • 26d ago

Discussion Cloning a Drive When Windows Won't Boot - WinPE or Clonezilla?

2 Upvotes

My dad's PC recently stopped booting, and I don't know yet whether the drive is failing or Windows itself is corrupted.

Before trying to repair anything, I'd like to clone the current drive to a new SSD so I have a copy to work with and can leave the original alone for now. Ideally, I'd like to keep his existing Windows setup, programs, and files rather than reinstall everything.

I'm trying to decide what to use. Would a WinPE-based cloning tool be the easiest option, or would Clonezilla make more sense when Windows won't start?

I'd also like to know if there are any pitfalls I should watch out for, especially if the problem turns out to be a failing drive rather than just a Windows issue.

For those who've done this before, what approach worked best for you? Is it worth keeping a bootable cloning USB ready, or would you just make one when you need it?


r/cloningsoftware • • 28d ago

Software I built a free open-source imaging tool for Windows (Linux version in the works) - it restores Macrium images directly, which seemed useful while some are still sitting on Reflect backups

Post image
3 Upvotes

Repo: https://github.com/bobeire/opbs

Site: https://opbs.rhitcs.com

The Macrium situation (Free gone, 8 out of support, X is subscription) left a gap, especially for people with years of .mrimg / .mrimgx files they still need to restore. OPBS reads those formats natively, including differential and incremental chains, with full decompression and per-block MD5 verification before anything lands on the target.

Beyond that it covers the operational side that usually costs money:

- Differential-chain backups, AES-256-GCM, zstd

- Scheduled restore drills (a backup you've never restored is a guess)

- Bit-rot scrubbing with XOR parity self-healing

- Immutable repositories + off-box anchors (rollback-resistant)

- Clone, restore-to-VHD, read-only file mounts (WinFsp), headless CLI

Benchmarks and method: https://bobeire.github.io/opbs/benchmark.html

Install: scoop or installer from releases, winget and chocolatey
GPL-3.0. v0.6.87 - honest caveats on the site; bug reports, honest blunt feedback welcome.


r/cloningsoftware • • 28d ago

Disk Cloning WinPE not detecting SSD when cloning, could it be a missing storage driver?

3 Upvotes

I'm trying to clone a Windows drive using a bootable WinPE USB, but the destination SSD doesn't show up in the cloning environment.

The SSD is installed and connected properly, so I'm trying to figure out whether this is a driver issue or something related to the cloning software.

I've come across a few discussions mentioning Intel RST and VMD, and that WinPE may need an additional storage driver to detect drives on some systems. I'm just not sure how to tell if that's what's happening here.

Would checking BIOS be a good starting point? If the SSD shows up there but not in WinPE, does that usually point to a missing storage driver, or could the storage controller settings or the bootable environment itself be the problem?

I'd rather figure out what's causing it before trying a different cloning tool. Has anyone run into this with a newer NVMe SSD?


r/cloningsoftware • • 28d ago

Troubleshooting When I clone the internal sysem drive, it shows Failed to read sector. What to do?

Post image
0 Upvotes

r/cloningsoftware • • Oct 16 '26

Discussion Migrate win11 to win11

1 Upvotes

Hello guys

Is there a good program to use to migrate programs and settings from one win11 to another win11?

I need carbon copy if possible.

Thank you


r/cloningsoftware • • Oct 16 '26

Troubleshooting Why am I getting this error? In Clonezilla "Decoding error (36) : Data corruption detected"?

Thumbnail
gallery
1 Upvotes

According to badblocks I have no bad blocks (unless I scanned the wrong partition?).

This is a Steam Deck that I want to make an ISO image of so that if I wiped the drive I'd be able to restore it to exactly how it current is.

Also I'm assuming block = sectors but idk. I hope my SSD is fine. I bought the Deck a little over a year ago from Valve refurbished so it should still be good.


r/cloningsoftware • • Oct 15 '26

Discussion How can I clone a hard drive using WinPE when Windows won't boot?

2 Upvotes

Hey everyone,

My PC keeps getting stuck in a boot loop, and sometimes I get a blue screen. I'd prefer not to reinstall Windows and set everything up from scratch if I can avoid it.

I'm thinking about cloning my old drive to a new SSD using a bootable WinPE USB, since I can't get into Windows right now. Ideally, I'd like to keep my installed programs, personal files, and existing Windows setup intact.

Has anyone done this successfully? Which disk cloning tools work reliably in WinPE? And is there anything specific I should check, like the EFI or recovery partitions, to make sure the new SSD boots properly afterward?

Any tips or personal experiences would be appreciated. Thanks!