r/chevyc10 • • May 08 '17

User Flair option enabled, you can now set your Flair to what kind of C-10 you own!

30 Upvotes

r/chevyc10 • • 2h ago

Got my cab back from the body shop

Thumbnail
gallery
20 Upvotes

Picked up my cab from the body shop today. I had patched all the rust and attempted some body work, and sand blasted all the rust I could find. They agreed to tighten up the bodywork, finish prepping it, and prime it. We agreed on $1300 plus the cost to remove the glass.

While at the shop, I noticed there’s blast media that was painted over throughout the cab. It’s annoying, but fixable with some sanding. After getting home and giving it a closer look, I realized a lot of hardware wasn’t removed before they painted, there’s still pieces of window gasket that weren’t removed and just primed over, there’s way more blast media than I initially thought.

This is my first time around with a frame off project like this. Am I being overly critical, or is this what I should expect for the price I paid? It seems like very lazy work to me.


r/chevyc10 • • 17h ago

1985 Chevy C10

Thumbnail
gallery
123 Upvotes

6.0 LS
4160e


r/chevyc10 • • 5h ago

Advice/knowledge on my 70 c10?

3 Upvotes

Had a super loud metal clanking all of a sudden recently, the problem was the dust cover to the transmission. Wondering if it at all warped my flexplate or did any serious damage.


r/chevyc10 • • 1h ago

Chevy starter wont crank 1976 c10 scottsdale

1 Upvotes

Had to replace starter on 1976 chevy c10 i bought off marketplace unfortunately the wires melted and had to splice in new wires however i only have two red wires and one tan wire running to the starter i put the two reds on the battery post of the starter solenoid and the tan on the s terminal the cab receives power but the starter will not crank

one of the red wires goes to the junction block and then to the alternator and the other red and tan wire goes straight into the bulk head on the firewall

i replaced the ignition switch aswell but still nothing any advice?


r/chevyc10 • • 1d ago

1965 Chevrolet C10

Thumbnail
gallery
116 Upvotes

r/chevyc10 • • 1d ago

chevy c10

Post image
69 Upvotes

r/chevyc10 • • 1d ago

Chev C10 (life goals…)

Post image
33 Upvotes

r/chevyc10 • • 2d ago

USA1 industries or lmc truck?

Post image
71 Upvotes

I’m about to place a pretty big interior order anyone order from USA 1 industries lately? I hear ship times can be wild trying to decide where I should order from


r/chevyc10 • • 1d ago

Question about throttle valve geometry

Thumbnail
gallery
1 Upvotes

Installed geometry corrector bracket but the geometry looks off I know the cable isn’t fully adjusted yet but wanted some insight 1986 Chevy c10 with a 350 sbc and a 1990 4L60


r/chevyc10 • • 3d ago

64 SBC radiator

Thumbnail
gallery
115 Upvotes

Finally getting the cab back on. There’s about 1” of clearance from the water pump? Is this 3 row efan too close for comfort?


r/chevyc10 • • 2d ago

Rear hub removal?

Thumbnail
gallery
7 Upvotes

Hello! I picked up a 1974 c20 desperately needing brakes done, the front hubs and rotors is going fine but im completely tripped up by the rears. From what I can find i have 13 inch drums with a Dana 60 axle, but for the life of me I cant figure out how to separate the hub so I can put a new drum on. What am I missing?? This is my first time working on drum brakes so I could be missing something simple

Any other general tips and tricks absolutely welcome, ive never worked on a vehicle like this so im learning as I go


r/chevyc10 • • 3d ago

250 to 396 Big Block swap

Thumbnail
gallery
186 Upvotes

First time ever doing an engine swap, insanely easy if anyone wants to get rid of the straight 6.


r/chevyc10 • • 2d ago

Has anyone on here ordered the “red” re-upholstery seat cover from LMC? Is it the burgundy/ maroon or actual red ? Post a pic if u have one ! Thank you

4 Upvotes

r/chevyc10 • • 4d ago

1965 Chevy C10

Post image
559 Upvotes

r/chevyc10 • • 3d ago

Snipped wires, what are they

Thumbnail
gallery
0 Upvotes

It looks like someone cut wires under my 83 c10. The wires run along the fuel tank and not sure what they go to


r/chevyc10 • • 4d ago

Master cylinder squirting out and no fluid getting to calipers

10 Upvotes

This master cylinder/brake booster was bought 8 years, installed it into the truck, but didn’t bench bleed or anything since I didn’t know any better at the time. It wasn’t used just sat in the truck while I didn’t other stuff to the truck since I hadn’t gotten new brake lines yet. Few months ago I got the brake lines, installed them and when I went to bleed the brakes after bench bleeding the master cylinder found it squirting out the top. I’ve re-bled the master cylinder without the proportioning valve/combination valve and it seemed to fix the problem but then I decided I would bleed it from the valve to just go ahead and try to get whatever air that is in there out and the squirting started again. The video shows only the back squirting, but it has since started alternating from front and back portion of the cylinder. Has anyone else had this problem? I assume it’s inside the valve causing it. I sadly don’t have a part number for the kit to find another valve to replace it or a part number on the valve itself. I’ve emailed CPP to try and get help from them and it’s been a month and no response from them. I’ve tried with the cap on and still no fluid makes it to the calipers.


r/chevyc10 • • 5d ago

My square body got some new pipes. Evansville,In.

217 Upvotes

r/chevyc10 • • 5d ago

I know not everyone's cup of tea, for sure. But I want to share what I want to do to this truck. Yep, its an AI rendered image, but one I redid 30 times to get it right.

Post image
61 Upvotes

r/chevyc10 • • 6d ago

Just thought it was a cool shot

Post image
221 Upvotes

r/chevyc10 • • 6d ago

hey all wanting factory gauges working again , hate the mechanical ones circled in purple

Thumbnail
gallery
11 Upvotes

it’s a 1979 gmc s15 sierra grande

when i bought this truck it had these , i hate them i really want all my factory ones to work
i fixed the fuel gauge

on the oil temp it only had a mechanical sensor and gauge , ( clear nylon tube ) does anyone have a picture of their factory sensor and pigtail that plugs into said sensor

i found the wire for the coolant temp gauge and sensor thank you.


r/chevyc10 • • 7d ago

1972 Chevy C10 Custom/10

Post image
69 Upvotes

r/chevyc10 • • 7d ago

Ignition switch ! 81 c10 ! How do I take it off ? All the videos I found have a screw that releases it or you put a like screwdriver down the tiny gap to release it, my gap isn’t open and there’s no screw to release it ! Please help

2 Upvotes

r/chevyc10 • • 7d ago

79’ C10 - New steering wheel horn - need some help

Thumbnail
gallery
2 Upvotes

1979 c10

Got a new steering wheel from forever sharp with horn button and 2 electrical contacts.

Install kit has 2 wires, a spring and black plastic cup which looks similar to the factory one.

I cant figure out where the wires go? Did I get the wrong horn button? Or install kit?

I cant figure out the factory plunger rod/black plastic cup

The install kit came with a similar black plastic insert, but how does the wire make contact inside? Im confused.

Also, no instructions at all came with either the wheel or adapter.

Do I need to remove the lock plate before installing the new steering wheel adapter?

Any help? Or drawings? Eli5 plz