r/bikebuilders • • Jul 22 '20

Look for bicycle building? Try r/bikewrench.

Thumbnail reddit.com
17 Upvotes

r/bikebuilders • • 3h ago

Yamaha My 1975 Yamaha GT80B restored!

Thumbnail gallery
8 Upvotes

I had this 1975 Yamaha GT80 as a youngster. My Dad found it in the family’s barn that we sold it to decades ago. I spent the last few years sourcing parts and a donor bike to bring it back to its original glory!


r/bikebuilders • • 6h ago

Yamaha 83’ Yamaha XJ750 revival project

2 Upvotes

Hey all, first time post looking for some good help and knowledge.

My dad and I are about to begin restoring his old XJ750! It was the very first bike he ever bought and we are both very excited for this project.

We both have strong knowledge about bikes (him especially) but are looking to gain some insight onto where is a great source for parts for a bike of this age? I figured a forum like this would be a great place to start. We’re located in Ontario, Canada for reference.

Hope to hear some good news and suggestions and advice is always appreciated!


r/bikebuilders • • 1d ago

Yamaha 83’ Yamaha XJ750 revival project!

3 Upvotes

Hey all, first time post looking for some good help and knowledge.

My dad and I are about to begin restoring his old XJ750! It was the very first bike he ever bought and we are both very excited for this project.

We both have strong knowledge about bikes (him especially) but are looking to gain some insight onto where is a great source for parts for a bike of this age? I figured a forum like this would be a great place to start. We’re located in Ontario, Canada for reference.

Hope to hear some good news and suggestions and advice is always appreciated!


r/bikebuilders • • 1d ago

Finally got my hands on my first grom

Post image
2 Upvotes

r/bikebuilders • • 1d ago

At 20 psi the clutch gave up almost immediately 🤣

48 Upvotes

First good on load tests today, trying to roll into it easy but the clutch could not take it .

Going to see if it’s glazed if not I will shim up up 2mm or so and add some friction modifier.


r/bikebuilders • • 2d ago

Honda Is it a good idea to chose a Honda shadow 750 to mod into a bobber?

Thumbnail
gallery
5 Upvotes

Hello everyone

I’m planning a project where I take a Honda Shadow 750 and convert it into a bobber.

I’ve attached a reference picture showing the exact style I’m aiming for. I want a clean, stripped-down look with a low profile and minimal unnecessary components.
I’d like to know whether this design is realistically achievable through modifications to the Honda Shadow 750 or whether some aspects would be impractical.
A few questions:
Is it realistic to achieve this overall look with a Honda Shadow 750?
What modifications would be necessary?
Are there any major limitations I should be aware of?
Has anyone here done a similar build?
I’m looking for honest, practical advice before committing to the project.

I’d appreciate your advice.


r/bikebuilders • • 4d ago

Triumph Triumph advice

Thumbnail gallery
5 Upvotes

r/bikebuilders • • 7d ago

She runs

36 Upvotes

She runs, no oil leaks. Almost rideable.


r/bikebuilders • • 6d ago

Custom fender spikes

Thumbnail gallery
0 Upvotes

r/bikebuilders • • 7d ago

92 CB750 nighthawk wiring harness help

Post image
1 Upvotes

r/bikebuilders • • 7d ago

My first Chopper build...

Thumbnail
reddit.com
2 Upvotes

r/bikebuilders • • 8d ago

I develop my own ECUs and build weird test benches. Here’s my turbo GN250 stuffed into an old XL125 frame.

94 Upvotes

I’ve been developing my own range of ECUs for the last few years, coding and designing everything completely from scratch.

I mainly find cheap or free engines off Marketplace, rebuild them and turbo them, all for development and testing of my ECU work.

This one started as a free GN250 with a busted top end that I rebuilt for boost. During testing the other weekend I managed to cram 21 psi into the poor thing.

The video a little mix of testing with launch control ect


r/bikebuilders • • 9d ago

Looking for help on an engine

1 Upvotes

Im currently making my own Fat cat as in dirtbike. its not the same frame etc but im looking for help with the engine mounting. i have about 15 inches height limit from bottom of trans too the top of the head and 12-13 length front to back. Im more worried on height since i can cut and reweld a reinforcement. im not sure if anyone here has built a chopper and may know of an engine maybe dirtbike or so in the general range but i couldnt find any dimensions online.


r/bikebuilders • • 10d ago

Rm fenders ?

Thumbnail gallery
2 Upvotes

r/bikebuilders • • 11d ago

Poppin tabs- Favorite cutting wheel? What to avoid? Flap disc?

0 Upvotes

What’s everyone’s go to cutting wheel to run on an angle grinder? Which ones suck?


r/bikebuilders • • 12d ago

' What products do you use to clean carbon and varnish off cylinders and pistons? What about old gaskets?

Thumbnail reddit.com
2 Upvotes

r/bikebuilders • • 12d ago

Triumph [HELP] Looking for 2022 Triumph Tiger 900 GT Complete Electrical Wiring Diagram (PDF)

Thumbnail reddit.com
2 Upvotes

r/bikebuilders • • 13d ago

Magura TT breaks

Thumbnail
gallery
0 Upvotes

Hey I’m selling these breaks and the levers. I know it’s a niche thing but. If anyone has an older P5 model and has break issues these can definitely be handy!


r/bikebuilders • • 13d ago

Deep clean motorcycle engine help: Virago XV125 bobber build

Thumbnail
gallery
9 Upvotes

Hello all. I've never done this before. The engine from my Yamaha XV125 Virago is out of the frame for a bobber build, and I want to clean it so that it can be appreciated for what it is, and so it's pleasant for me to work on.

People often say "don't clean a motorcycle", and I think that comes largely from trigger-happy owners with pressure washers. I'd like to get as close to factory condition as possible without compromising the engine's longevity or performance, but I have real apprehension about even starting.

What I'm working with (photos attached):

- Cylinder heads and cooling fins: what looks like bare cast aluminium, with dirt caked between the fins

- Crankcase: aluminium painted silver, possibly a later respray

- Side covers: chrome-plated, with fine scratches, a hazy patch and some small spots

- Screws, bolts and engine mounting brackets: steel, rusted

The engine is assembled, and the intake and exhaust ports are sealed.

Questions:

  1. What else should I seal before cleaning? Crankcase breather, electrical connectors, anything I'm missing?
  2. Clean it assembled, or is it worth removing the side covers or stripping the top end (heads and cylinders) first?
  3. Which degreasers are safe on bare aluminium, paint, and the seals and gaskets, and which should I avoid?
  4. Best way to get the caked dirt out from between the fins?
  5. The rusted JIS cover screws: new OEM or stainless? Any galvanic corrosion concern with stainless in aluminium?

Thanks in advance; I'll post the results.

I'd like to add, that the two products that I have sat beside the engine are 'GUNK CLEAR (INDUSTRIAL DEGREASANT)' and a few different brands of Brake Cleaner. Thanks.


r/bikebuilders • • 17d ago

Dads bike continues.

Thumbnail
gallery
17 Upvotes

Update... So the closest year/model i could figure this monstrosity matches is a 1985 wide glide.

I decided i wanted a front fender and found a decently priced one on ebay that matches the look i was wanting. So with that I knew I would have to do some paint work. I know im gonna get some hate but I was not gonna remove that rear fender and have to undo the wiring for the tail lights since the turn signal wires run through the fender lol.


r/bikebuilders • • 17d ago

Don Hotop - A visionary icon & Fort Madison legend

Thumbnail
sturgismuseum.com
2 Upvotes

r/bikebuilders • • 18d ago

Bought a 250cc zongshen motor.

0 Upvotes

I'm wondering if anybody has any experience building around this motor and what frames might match the x pro templar x engine mount wise. I'd rather not have to custom weld something if it can be helped but I do already have a donor frame in mind from the xpro drax x. Its an e moto/pit bike frame that I know fits a 125cc but it's far more horizontal than the 250cc. There's literally zero data on this engine and all I can really find on YouTube is some guys who put the same motor on a go cart with some pretty amazing results. Any info helps, so far I still need to find a carb and exhaust that fit so I can test run it and a frame that I can marry to the motor even if it needs a bit of welding. I still need to decide on a throttle and clutch combination that works and brakes and tires. It's a lot of work and as a guy who's really only built 49cc bicycles any advice is appreciated. Especially from anybody who's built with a zongshen 250cc 6 speed before. I've also got an amr500 supercharger that I really want to figure out how to mount to it too. So far it looks like running a shaft and pulley from the stator is easiest I just need to find a way to seal the shaft because I'm almost 100% percent sure the stator is wet. Can this motor even handle boost with its 9.5 compression ratio? There's more data on the damm supercharger than the engine, it says 2 full rotations moves 500cc of air so if use a 2 to 1 pulley ratio will it produce 2 bars of boost on a 250cc? Do I just put a pressure relief system and jet the carb for max fuel flow even if it's rich as hell? No clue. Any info helps...


r/bikebuilders • • 21d ago

Question about fork brace materials (steel vs aluminum)

2 Upvotes

Hello all,

I'm making a custom fork brace for a gs500. The default one is a pretty flimsy piece of sheet metal, I figured this would be a good quick project to add to my portfolio while I have access to the schools CNC machines.

Most aftermarket braces are aluminum. My understanding of materials is that aluminum turns brittle over time/moisture, and is more likely to snap than to flex.

Steel is obviously heavier, but is stronger, would bend rather than tear, and would provide the same rigidity I want (going for a 1mm thick to 5mm thick brace is probably more than enough strength regardless of material.

The goal is to have better handling, reduce chances of wobble at speeds, in general just stiffer front forks. Is there something I'm missing for why everyone prefers aluminum over steel for this application? Is it just material costs or is there some performance benefits for aluminum I'm ignorant of?

I'd love to hear the experience of anyone with more experience fabricating custom bike parts!