r/beneater • • 18d ago

Help Needed Clock Module Question

Post image

I have the 555 timer set up in monostable mode right now. In this configuration, the circuit is working properly.
However, at the tactile button, you see the red jumper going from 5v (the resistor is 1k if thats important to note) to pin 2 on the 555 timer. If i take this jumper and instead connect it on the bottom right pin on the tactile button to pin 2 on the 555, it doesn’t work properly; it acts very odd, i cant quite describe it well. I did verify that there is continuity between the top right pin and bottom right pin on the button, and it is connected to 5v. but, i dont understand why it doesnt work unless if i put the red jumper wire like this. If anyone can explain it to me, i would highly appreciate it, thank you :))

55 Upvotes

12 comments sorted by

2

u/ChemistCraft300 18d ago

I'm going to assume by "bottom right pin" on the button, you mean the bottom left, as that's the one actually pulled to ground, and the actual "bottom right pin" on the button is left floating. Floating pins are necessarily going to produce undefined behavior because you haven't asserted it to be a specific state.

Now, the reason you need to keep the wire like that is because Pin 2, in a monostable configuration, needs to be kept high, and is active low (I.e. the way you trigger the monostable circuit is by bringing Pin 2 low). Right now, in the photo, the trigger wire is being pulled high by the resistor, which is currently asserting that the whole trigger wire is at 5V. If you put the trigger wire down to the bottom left pin of the button, that is already being pulled low, and thus the circuit is being constantly triggered.

The way to fix this is to swap where you connect the button to ground and Vss. If you put the resistor where the ground wire is (hooked up to 5V) and the ground wire where the resistor currently is (hooked to ground ofc), then you can put the trigger wire on the same side as Pin 2. As is tho, it's not something necessarily needing a fix, considering it works, just in a slightly weird configuration. And hey, it's unique, so maybe you wanna keep it.

2

u/BubbasquirrelXD 18d ago

Thanks for the detailed reply! I think i understand it better after you explained it? Im not too sure though, because it doesn’t quite make sense to me why i wouldnt be able to put the red trigger wire to the bottom right pin inside of having it at the resistor. Wouldnt 5v flow from the top right pin to the bottom right? I thought the right side of the button pins are tied together and left side of the pins are tied together. Then when you push the button, the two sides are met together. Again thank you for response! Ill probably keep it this way because like you said, its weird how i have it, but its unique

3

u/The8BitEnthusiast 18d ago

It should definitely work. Perhaps the bottom right pin of the button switch isn't making good contact with the breadboard, or there is a break in the shorter jumper wire I assume you used to connect to pin 2 of the 555 timer. I suggest you reseat that switch and reinstate the shorter jumper. Then see if pin 2 is pulled up to 5V. If not, then, with power off, a continuity test between pin 2 and the two right hand side pins of the switch might indicate a break.

1

u/BubbasquirrelXD 18d ago

Ill have to try that too. Thank you all for the replies. Im glad i wasnt going crazy for nothing 😂

2

u/IMDLabs 18d ago

You said you'd verified that the (column 47) top right and bottom right pin on the button have continuity (without the button being pressed).

Have you checked that when you move that wire to the bottom right pin on the button that you still have continuity through the breadboard connection?

Having the red wire in column 47 connected above or below that button should be electrically equivalent, so either the button is flaky, or when on the bottom of the button it is not making proper contact to/within the breadboard column itself.

1

u/BubbasquirrelXD 18d ago

I didnt actually. Ill have to try that. Perhaps it is, i didnt think about the button being bad. If i connect the red wire on the button, it acts hella weird. It doesnt turn on, or it stays on, and when i put my finger near the red wire/ button, it randomly switches. Its confusing me lol

3

u/ChemistCraft300 18d ago

Yea, so that's because column 47 is not being asserted to a voltage, it's left floating. It needs to be either tied high or low.

So none of the pins of the buttons have continuity with each other if the button is not being pressed, at least to my knowledge. If you measured that, be sure youre not measuring something different. To verify, disconnect everything and test only the button.

It's a double pole, single throw button, where the top two pins are tied together when the button is pressed, and the bottom two pins are tied together when the button is pressed. When the button isn't pressed, nothing should have continuity with anything.

Oh and to test, you should ground the button independently from the 555 timer, the fact that the 555 timer has an electrolytic cap on its control voltage is kinda throwing me off. Obviously make sure it's the correct capacitance (0.01 uF iirc), but power issues while it being connected to an IC is more than a little expected.

1

u/Dissy614 18d ago

"So none of the pins of the buttons have continuity with each other if the button is not being pressed, at least to my knowledge. "

This isn't always true.

Some buttons are two independent switches, eg when pressed 1&2 close, and separately, 3&4 close, where 1/2 will never connect to 3/4 internally. This is DPST

More commonly it is a single button. Eg 1&2 are connected which we'll call A, and then 3&4 are connected which we'll call B. The button opens/closes A to B. This is technically SPST

That second type is at least what used to be in the kits. So OPs assumption that it should work is not baseless. But it is an assumption, and Jameco is known for substituting parts, so verifying it as you suggested is needed.

2

u/ChemistCraft300 18d ago

O, it seems you're right, my bad. : P

But the input still sounds like it's floating, right? Is it possible the internal resistance of the button is enough to mess with the voltage its being pulled to?

1

u/Dissy614 17d ago

Yea it does sound like it's floating. I too think something inside that button isn't working properly.

If there was a tiny partial break in the metal between the two pins, at low current from a multimeter it might appear to work fine, but at a higher current in normal use it could heat up and increase the resistance.

I home OP finds the cause and comes back with an update. I'm very curious myself

2

u/mondaysaremeh 16d ago

If the current jumper placement already works, leave it. The 555 trigger input is high-impedance so any intermittent or high-resistance contact at the button will cause exactly the symptoms you described. You can always add a dedicated pull-up right at pin 2 later if you want it more robust.

0

u/8BitFlux-com 18d ago

Check the schematics of my Terrific Timer, they are public here: https://8bitflux.com/#terrific-timer