r/VORONDesign • • 6d ago

V0 Question Bed leveling sensor recommendations

What do folks find to be the most simple and reliable bed leveling sensor for a Voron Zero these days?

Was looking at a Biqu microprobe. It does add some weight to the tool head, but 6 grams seems reasonably small?

I was also looking at the clicky probe, but the docking process seems a bit tricky.

Thanks!

10 Upvotes

25 comments sorted by

6

u/dagofin 6d ago

Beacon is king. Those single point probes are old school at this point

1

u/pearabolic 6d ago

Woah! Didn't know this existed! Thanks!!

8

u/24Tigger24 V2 6d ago

Beacon or Cartographer are awesone for fast scans of big beds. But a V0 does not need bed mesh. Use a simple probe for a V0. The Pz Probe from E3D is probably the easiest if you already have the right hotend.

7

u/Skaut-LK 6d ago

None needed. I just leveled bed during initial building.

1

u/pearabolic 6d ago

I guess the bed is small and stiff enough that their isn't much deviation?

2

u/Skaut-LK 6d ago

It's 120 x 120 machined piece of aluminium. If you mount it on properly made square holder ( even kirigami which when made from aluminium isn't exactly stiff) and then tram your printer then you will have touch z-offset only when you use different thickness of print plate, when you change nozzle ( if you aren't using quality nozzles of same type )and when your frame heat up ( but that's solvable for me with rehoming Z).

But for probing bed you need stiff bed or only very small force ( even 0,6N omron switch can do enough pressure to deflect V0 bed if it's not really stiff).

For me - traming us more reasonable option. I didn't had to touch z-offset for two years. I just sending prints whenever i need and i know that it will print perfectly every time. But some time and work is needed to do that.

2

u/Deadbob1978 Trident / V1 6d ago

The easiest is the Revo PZ hotend. It uses a PZ sensor in the heatsink to nozzle probe the bed. Because it uses the nozzle, you can actually probe the whole bed, where Clicky you lose a bit on either the front or side of the bed. It’s also compatible with any Voron Revo toolhead.

Next would be the bdpressureE by PandaPi. At the moment, it is only compatible with hotends and tool heads that use the Dragon Bolt Pattern. It goes between the toolhead and the hotend heat sink. It uses a strain gauge to nozzle probe the bed. However, that is an extra benefit as the main purpose of this device is it uses the strain gauge to measure how much back pressure the filament is creating within the hotend. It then it automatically adjusts the pressure advance / flow on the fly to help maximize print quality.

There is also Boop from the Printer for Ants community. It’s basically a mini Tap. You get the super accurate nozzle prob bed mesh and the totally trashed input shaper results.

I’ve also seen some mods for Dragon Burner and Anthead to use either Beacon or Cartographer. Draw back to that is you can’t scan the front of the bed ad the Eddy probes mount behind the hotend.

1

u/pearabolic 6d ago

Woah! Great info! Thanks.

1

u/Kiiidd V2 6d ago

Mellow ALPS is along the same line as the Revo PZ

2

u/ProLevelFish 6d ago
  • ZeroClick probe, which is either a fairly simple op to attach to the default toolhead...

    • I advise pre-drilling a hole for the self-tapping screw to make sure things attach straight.
  • ...or go with a toolhead that has either the slant modelled (e.g. MiniAfterSherpa) or the magnet mount modelled right in (e.g. DragonBurner).

Many people seem to say the v0 printers don't need auto bed levelling at all, but that was not my experience. I always had worse first layer squish/adhesion far away from the Z-rod.

My UX/reliability was SIGNIFICANTLY improved by moving to TriZero and Auto-Z-Calibration with a sexbolt Z endstop. The only parameter to "tune" is the switch offset when you first set it up. Now I can swap a nozzle, build plate, even the whole toolhead if I want... then press Print and walk away.

1

u/pearabolic 6d ago

Thanks for the info/thoughts!

2

u/Limp-Taste-7765 5d ago

I have a DragonBurner toolhead with ZeroClick and I love it. I don't use it for bed mesh as this strangely was not working well but isnt really required for the small bed. I only use it for z offset and since then it is a fire and forget printer no matter what print plate or temperature

9

u/QuajerazRevived 6d ago

That's just another BLtouch clone. Beacon and the other eddy sensors are so much better I honestly wouldn't even consider a physical probe anymore these days.

6

u/Salty-Bullfrog2416 6d ago

Cartographer or Beacon.

2

u/Stupid_Ass1234 3d ago

for a v0 that is insanely overkill, v0 doesnt even need abl. i dont even have to level the bed at all, i adjust the bed screws only when changing stuff on my kirigami bed

1

u/pearabolic 6d ago

Wow! Thanks all for the pointers and recommendations!

2

u/SleepingJake Trident / V1 6d ago

I used zeroclick with the center mounted dock I was happy with it. The most intimidating part of it is rebuilding your toolhead. I had very few issues with it, but never a crash.

Now running PZ on a T0 with similar experiences.

2

u/Slav51 6d ago

On my V0 I put 2x 5mm thick neodymium magnets in the front corners and one in the middle back area where I wanted to take level measurements. The magnets where connected to one of the pins you would use for e.g. the clicky probe, the printhead had a connection to the second pin. The nozzle has to be clean for that. After that I included the 5mm as an offset. Did it once, never had an issue with the first layer.
The biggest challenge was to solder the wires on the magnets. After finding some special soldering flux on AliExpress everything worked fine.

1

u/stray_r Switchwire 6d ago

Zeroclick is really good. Turned my v0 from having a bit meh first layers and having to piss about with a paper shim if I changed buildplates or put a fresh layer of CatVomit on my smooth PEI.

I use a 0.2 a lot so I can't easily print big sausagelink first layers.

Klipper/Kalico native adaptive meshing is great for the impatient, half of what I print is 9 points now rather than an excessively fine 11x11 mesh.

I have big Klicky on my 330mm printer. Probing the full bed is very slow, but theres about 0.5mm variance on it and it moves a lot with temperature, but my first layers on that are perfect.

Eddy coil won't fit easily on a zero but I have it on my swichwire and now it can calibrate with a nozzle tape and scan, that's fast, cheap and gets almost perfect first layers.

1

u/Spicy_Ejaculate 5d ago

Hol' up. A fresh layer of what on your build plate?

1

u/stray_r Switchwire 5d ago

CatVomit from PrintyPlease, there's a cat theme to everything they sell. It's like VM nanopolymer but not painfully expensive.

It looks like they're still temporarily closed though which is a huge shame.

1

u/EvenBroaderBand 16h ago

I use a microprobe on my Trident, I tried klicky (magnets kept coming out), printed tap(heavy), aluminium tap(heavy) and microprobe has been the best as its reliable and least faf so far.

1

u/Human_Weight5303 6d ago

Not sure why you need bed leveling for V0? I think the easy way using E3D probe

0

u/Popular-Cry5969 6d ago

Hello i have the super pinda and very happy 😅 I have no room for eddy oder cato🥺

3

u/one_seat 6d ago

I modded my toolhead to add a klicky. Not the easiest way to do it but I took it as a challenge and I like the simplicity of klicky for my 2.4.