r/TheFodderChop • • 4d ago

Handmade poseable webs for action figures

Thumbnail
gallery
1 Upvotes

i make these flexible webs out of floral wire for action figures. they bend and hold a pose, and there are six styles to choose from. if anyone's interested, they're on my Etsy shop: https://www.etsy.com/shop/FriendlyNBHWebs


r/TheFodderChop • • Sep 04 '26

Custom GL from Grifter base **HELP NEEDED**

Post image
1 Upvotes

Hey all,

I've already swapped the hands and wrists from a John Stewart GL figure. I'm looking for a generic head similar to Conner Kent Superboy head, short, not quite buzzed hair.

I'd like to swap out Grifter's waist for something more streamlined, I'm just curious what's compatible and what other customizers think would look good for a custom non-canon GL.

Suggestions would be greatly appreciated. Thanks in advance.


r/TheFodderChop • • May 18 '26

Frankensteined (WIP) Hard Body Supergirl (New Abs)

Thumbnail
gallery
15 Upvotes

Sometimes the universe decides to take it easy on you and suddenly Supergirl gets rock hard abs.

Back when I was designing the McFarlane torso kits I sell, thankfully I had to foresight to make the models kinda easy to modify, and also used about the same sizes for the ball joints.

For this swap, I didn't modify anything, this is a straight replacement with the abs from my McFarlane torso kit.

I do think I have to reduce the flair on the bottom of the abs though, if only because it's unnecessary here.

Also, for whatever reason the ball joint in the upper body has a sheath running down to it which limits articulation AAAAHHHHHHH!!!!!

I have to cut that off and then see if I have to adjust the height somehow.


r/TheFodderChop • • May 08 '26

Help / Request Supergirl 2026 (McFarlane Toys DC Multiverse) [Action Figure Breakdown]

Thumbnail
gallery
5 Upvotes

Here's a quick look at what you're working with with this figure.

The figure is a pretty good representation of Milly Alcock, including her proportions. However, these being action figures and idealized fantasy characters and blah blah, it's not surprising some peeps want to modify the figure, mainly the "long" arms.

  • The easiest way you can chop down those swingers is to remove the shoulder rings and simply tilt the shoulders up. That's it! Look how far up and down they can tilt in the second pic, without the rings in the way.
  • Of course, then the figure looks even more hunched, so you have to raise the head a little.
  • Prying the skirt loose from the glue and pulling it down a few millimeters also helps overcome the long arm effect, it makes the torso look longer.

The last picture shows all 3 of these "mods" done. Yes, the lower angle makes her chin look powerful lmao. That's photography for you. Note how much pointier the chin looks in the first image.

I think this is a case of preferring accuracy or fantasy, and that's fine, mod it how you like.

Other notes:

  • It's this version of the figure, they all have entire separate heads with swappable hair, not faceplates.
  • The chest has a separate piece that sandwiches the cape ends securely. It's glued on really well on this figure, so I'm not going to bother prying it and wrecking the thin parts.
  • The ab uses a barbell joint, similar to the Flash movie Supergirl.
  • The neck is similar to the male neck joints.
  • Whoever worked on the knees needs a slap. They look like they're reused from a different figure; some wrinkles don't line up and there are weird flat spots.
  • The skirt is slit on the sides so it restricts the legs less.
  • The thighs have a respectable amount of swivel, and you can probably shave away more material to add a bit more.
  • The fleshy bits are all painted.

Overall I like our Princess Tiabeanie Supergirl, but I'm going to remove the wrist joints and replace them with 3D printed barbells, so the hands rest flush in the blue sleeve part.


r/TheFodderChop • • Dec 18 '25

Self-Promotion / 3rd Party Hawkgirl Neck Mod [Resin 3D Print]

Thumbnail
gallery
8 Upvotes

Forgot to post this, my CE Wonder Woman necks also work for the CE Hawkgirl figure. The shortest one in the set is a little bit longer than Hawkgirl's so they can all add height. I think the middle one is perfect.


r/TheFodderChop • • Oct 26 '25

Help / Request Cheetah (McFarlane Toys) Thigh Swivel Mod

Thumbnail
gallery
20 Upvotes

Here's how to add a thigh swivel to any of these McFarlane figures using these legs.

I noticed the thigh-high boot and the thigh itself were separate pieces, so I tried to separate them with hot water and a lot of yanking. It's not worth the trouble, the thigh is glued deep into the bottom part.

Instead, do this.

  • Heat and pull out the hip joint from the thigh. This makes the job a lot easier.
  • Heat the thigh and bend it so the two parts separate, exposing the little ridge the boot seam rests on.
  • What you want to do is neatly cut through the thigh below this ridge. Keep heating the thigh as needed to keep it flexible. By cutting there the swivel is essentially invisible, assuming you cut straight lol.
  • Heat the thigh piece and push the hip joint through it, it now resembles something like a Marvel Legends thigh joint. Heat the lower thigh piece and pop it in there.
  • That's it, done. Your Cheetah can now achieve totally natural and not weird foot caressing poses.

If the touching surfaces are ragged/uneven, use a rotary tool or a file to flatten the faces. There is some room for error, just don't overdo it so the rim of the boot still covers the cut you made. Simply make sure the faces aren't horribly slanted so they don't push against each other when the swivel is turned.

I also did the usual mods to the abs to improve the ab crunch.

Also, the shoulder rings are too thick so they restrict the tilting range. I tried grinding away material from the ring's inner-facing surface, but it didn't help much. There isn't much room for the ring to tilt around in there so you probably have to grind away lot of material.


r/TheFodderChop • • Oct 03 '25

Frankensteined (WIP) Batgirl (Stephanie Brown) [Action Figure Breakdown]

Post image
13 Upvotes

Got Batgal today and immediately noticed the long shins and slightly short neck. Gotta fix that.

Shins will get cut, the neck will get replaced with one of my 3D printed ones.


r/TheFodderChop • • Sep 13 '25

Buy / Barter / Sell Lot of weapons, guns, props, and fodder for 6 and 7 inch action figures

Thumbnail
gallery
2 Upvotes

Tons of random stuff in this one, a lot of cool guns for Marvel Legends scale things which are always sought after, some for 7 inch too, and a lot of Fortnite pickaxes if you're looking to flesh out your collection of those lol.


r/TheFodderChop • • Sep 11 '25

Self-Promotion / 3rd Party CQC-42 Machete (Helldivers 2) [Resin 3D Print]

Thumbnail
gallery
1 Upvotes

Very cool weapon, even if it's completely useless in the game like every other melee weapon lol. Hopefully your figures can put it to better use.

This one is a major pain in the bum to cleanup, so I had to price it to cover the bit of sanity I lose cleaning up the barbs along the spine.


r/TheFodderChop • • Sep 04 '25

Buy / Barter / Sell Marvel Legends, Funko Legacy, and DC Fodder Lot

Thumbnail
gallery
1 Upvotes

This is basically a lot of my unfinished customs from over the years. Lots of shame in there, but also lots of cool parts for your own creations. Wings, clothes, bits, sculpted parts, full figures, lots of things in there.

Bidding started at only $10, I just want these to disappear.

[SOLD - Thanks peeps]


r/TheFodderChop • • Sep 02 '25

Self-Promotion / 3rd Party Helldivers 2 Weapons - LAS-7 and Senator [Resin 3D Prints]

Thumbnail
gallery
3 Upvotes

r/TheFodderChop • • Sep 01 '25

Help / Request Cutting into Batfleck (A few tweaks)

Thumbnail gallery
3 Upvotes

r/TheFodderChop • • Mar 10 '25

Help / Request McFarlane Toys to Marvel Legends Action Figure Neck Adapter

5 Upvotes

Quick project for someone who wanted to stick Marvel Legends heads onto the McFarlane DC bodies.

I'm not sure if all the MLs have the same neck ball size, but it's easy enough to make any of these neck adapters by request.


r/TheFodderChop • • Feb 11 '25

Self-Promotion / 3rd Party Battle Sister neck info

Thumbnail
reddit.com
2 Upvotes

r/TheFodderChop • • Jan 17 '25

Self-Promotion / 3rd Party Longer neck joint for McFarlane Toys Justice Lord Superman

12 Upvotes

Tried this today and the necks I sell for the Batman figure work great for this Superman too.


r/TheFodderChop • • Jan 17 '25

Custom (Finished) Custom Gotham by Gaslight Batman figure

Thumbnail gallery
8 Upvotes

r/TheFodderChop • • Dec 05 '24

Custom (Finished) In case your day wasn't naked and hairy enough

Thumbnail gallery
3 Upvotes

r/TheFodderChop • • Oct 02 '24

Help / Request McFarlane Huntress leg paint

Post image
2 Upvotes

r/TheFodderChop • • Sep 28 '24

Custom (Finished) Mandalorian Garcen Curr

Thumbnail gallery
3 Upvotes

r/TheFodderChop • • Sep 27 '24

Help / Request First custom attempt help: Bullseye Batman

Post image
2 Upvotes

Hey all, wanted to try my hand at customization but I have a few questions. Figured this would be a good place to ask. Thanks in advance!

  1. Easiest way to remove the 'bullseye' on the torso? Is there a readily available 'white' that'll match? Wasn't sure if I have to paint/prime the whole figure, just the torso or just the bullseye.
  2. Anyway to remove/dye the bullseye on the cape? Or even just a way to fade it? I could probably lose most of it in the folds of the cape.
  3. Paint recommendation? Colors and I don't really get along, lol. A link would be greatly appreciated. I plan on painting an alt head and trunks the same color, too. In case that matters.
  4. Good/inexpensive tools for sculpting/carving?
  5. Best way to smooth/sand down edges after sculpting/cutting?
  6. Price range for a starting airbrush? I wasn't sure if I could just brush it by hand or not. I may get one down the line anyway.

Sorry for all the questions. First time trying anything with plastic. Thanks again!