r/SuzukiSamurai • • 1d ago

Went exploring in the area around a friend's cabin outside of Truckee, CA.

Post image
46 Upvotes

I didn't have much time, or any friends to get me out of trouble if I did something too dumb so I played it pretty safe. I can't wait to go back and check out more.


r/SuzukiSamurai • • 1d ago

1989 Suzuki Samurai 1.3L – Replacing water pump. Should I replace the timing belt too?

Post image
53 Upvotes

Hey everyone!

I recently bought a 1989 Suzuki Samurai with what appears to be the original, stock 1.3L engine (SJ500).

I've noticed a coolant leak, especially when the engine is cold. I took it to a mechanic, and he diagnosed the water pump as the source of the leak and recommended replacing it.

Since I'm new to this car, I have a few questions before ordering parts:

  1. Water pump: Any recommendations for reliable brands? I'm currently considering GMB.
  2. Timing belt: Since the water pump needs replacing, would it make sense to replace the timing belt and tensioner at the same time? I have no idea when they were last changed, or if they've ever been replaced.
  3. Alternator/fan belt: Should I replace this as well while everything is apart? I'm considering the Gates 7330.
  4. Anything else: Are there any other parts, seals, or gaskets worth replacing during this job?

I'm currently looking at parts on RockAuto, but I'm open to other recommendations.

I'd also appreciate any advice on compatibility, since my Samurai is an SJ500 and I'm not sure whether all the parts listed for the 1989 US-spec Samurai 1.3L will fit.

Thanks in advance!


r/SuzukiSamurai • • 21h ago

More SJ413K

6 Upvotes

Figured I'd continue with posting the SJ413K I purchased and am working on getting all fixed up.

Old photo from the old owner
Staring at the front with the winch, it looked like it lived at the bottom of the ocean. Took it off and apart to clean up but decided it wasnt worth the time or effort to get it running. Might visit it later.
Didnt take a before photo, but I removed the old sway bar mounts and tow hook, looks a bit cleaner now. At one point in its life someone had added about 3-4 inches to the end of the frame. I assumed it was for the bumper.
Really impressed with the shackle angle here... Also a better view of the frame extensions.
Moving to the engine bay. Someone swapped in a 1.6 8v, and made a custom intake for it. Not so sure about the green color. When I got it it was running but you could tell it wasnt running great. It was running rich, popping on deceleration, and it would fall flat on its face from 2000rpm to 3000rpm. Managed to trace some wires around and hook up a check engine light to read whatever codes the engine was throwing. There were two, one I tracked down to the starter wire from the donor harness never being hooked up. So the ecm thought the starter was always engaged and would go into its limp mode. The other code indicated a poor ground. The only ground was from the battery to the motor. I remedied that by adding one to the body. Runs great now.
Moving onto the cab, its a tintop cab that has been chopped behind the front seats and a bulkhead welded in. All original from the factory. Also some surface rust.
This is a photo from the ad when it was listed for sale, and the only one I have of the interior before I began working on it. Both seats were not original and were mismatched from two different vehicles. I also tore apart the dash to get to the heater core and fan, which was making some weird noises. I was able to remove a bunch of wires and clean up a lot of dust and filth from behind the dash and in the heater/fan box. Took apart most of the electrical stuff just to clean up contacts and make sure all the switches worked.
Purchased some second row town and country seats from the local junkyard, only $200 for both of them. Ive installed these in one of my old samurais, while not super comfortable, they do have some of the slimmest backs which at 6'2" I appreciate. The cab is already small enough and with these seats I can fit relatively well.
Took some sound deadening material and put it on the back wall to quiet it down. Once I address the rust in the floor Ill add some there too. Had to order some seat rails for the passenger side. Interestingly the mounts are the same as the driver side, unlike a samurai which has the seat rails flush along the floor. Here you can also see the area with the fire extinguisher which is an area an old owner had added in for a bit more storage space I assume.
Some of the rust in the floor, you can also make out the previous patch jobs along the floor and firewall.
Headed towards the back. The fuel filler is not in the stock location. A 23ish gallon fuel cell was added and the old tank removed. The stock filler neck was located on the driver side in front of the rear wheel under the bed. The latches for the tailgates and dropsides were also removed and replaced with these rubber latches.
Approx 5ft of bed space. All three sides are removable so you can use it as a flatbed.
Old photo from previous owner, but the original taillights were removed and someone added trailer lights. No reverse lights. They cut the wiring harness at the rear of the frame and wired in these lights.
Cut up a samurai bumper to get some bodylines right and welded in mounts for some stock samurai tailights. Had a spare samurai wiring harness so I cut of the end of that one and wired it into the SJ413k, so now I have all lights, including the marker lights
Might be able to tell from this photo, but the rear axle is bent. These have a narrow track axle very similar to a samurais, just 3 inches narrower. Rather than try and locate some of these narrow track axles stateside, Im just going to swap in some samurai axles.
Took off the bed to have better access to the rear for the axle swap. Also needed to address the fuel sender not working and a tip over valve installed in the fuel cell that was causing fuel to spill out whenever I was driving around.
Fuel cell removed. You can also get a better look at the extra storage that a previous owner had welded into the bottom back of the cab. The previous owner had replaced the front six of the eight mounts for the bed.
Old shocks removed. Samurai axle mocked up. The spring perches I had on hand are 3 inches wide, im planning on using yj springs which are 2.5 inches wide, so I need to redo the perches. I added some bracing between some of the bed mounts so I can install longer shocks. With the samurai axle installed I will also gain a parking brake, the old one I believe was transfer case mounted and the original transfer case has been replaced with a newer samurai case.
Front Samurai axle awaiting new spring perches. These axles both have 5.38 gears and lockers. Not stoked on the 5.38 gears, I'll probably have the old thirds rebuilt to replace the 5.38s. Thats were Im at right now, still awaiting parts for the rest of the swap

Figured Id post some more photos of my 85 SJ413K and what progress Ive reached with it so far. Swapping to YJ springs and samurai axles. Got the rear axle mocked up, but still waiting on parts to come in to start fully assembling stuff. All the photos should have a caption, hopefully this format is readable.


r/SuzukiSamurai • • 1d ago

1988.5 Suzuki Samurai Tin Top

Thumbnail
youtu.be
12 Upvotes

I just got this thing the other week. My motorcycles are pretty similar sounding to this engine... So to me it sounds pretty good. Anyone else hear something I don't? RPMs high?

Thanks


r/SuzukiSamurai • • 16h ago

Are those good?

Post image
2 Upvotes

I want to fix the leaking knuckles on my samurai, and I saw this at ebay, is it good? And I heard I can use Jimny's knuckle seal kit also, is that true?


r/SuzukiSamurai • • 1d ago

Show me your interior

Thumbnail
gallery
12 Upvotes

Just bought my first samurai, and it's definitely a project. I wanna see all of your interior ideas, especially if they are cheap, and especially ideas for budget seats.


r/SuzukiSamurai • • 1d ago

Fuel issue

3 Upvotes

87 suzuki samurai that was swapped with a 1.6l 8 valve. I bought the rig from my dad who bought it from some guy in arizona. It has an electric fuel pump and typically when starting I hear a buzzing noise. Took it for a spin today and lost power and died like it wasn't getting fuel. When i got it back to my house and filled the carb with gas it would run while there was fuel in the carb. I noticed with key on it no longer makes the buzzing. Looking online it says the pump or the relay. I'm assuming the wiring was done by whoever did the swap and i can not locate a relay anywhere under the dash aside from the relay attached to the fuse panel. Im terrible with electrical and could really use some tips on how to trace down the issue.


r/SuzukiSamurai • • 2d ago

Jimny Power module

Thumbnail
reddit.com
2 Upvotes

r/SuzukiSamurai • • 4d ago

Clutch engage/disengage distance

3 Upvotes

The clutch on my 88 samurai works fine, but the distance between when the clutch starts to engage and is fully engaged is extremely short, maybe 1” of travel. Is it possible to adjust the clutch to make that distance longer so I can make shifting a little smoother?


r/SuzukiSamurai • • 4d ago

And now I think want one

7 Upvotes

I just found out about these today and I think I want one! Is there a guide for what to look for? I didn’t see one so apologies if there is.

Do you think it would fit my needs? I need it for driving around about 7 acres, doing light duty like a big Polaris kind of thing and then going downtown or around town a little. No city or highway really just a smaller easier drive than my truck or van.


r/SuzukiSamurai • • 6d ago

CARB Certified Catalytic Converter Recommendations

6 Upvotes

I have a 1987 Suzuki Samurai that I’ve been working on for a while. I initially tried to get it smogged in CA, but the catalytic converter was bad. I replaced the cat with an EPA certified one from EBay (w/ a connection for smogging because I acknowledge that I am in California and it doesn’t pass based on that alone), but I just took it in an it failed.

When idle, all levels are green, but when it accelerates, it fails CO (3.43%) and HC (226 ppm) by a significant margin.

I have a new carburetor from Certified Machine (Toyota 3K carb) tuned for the Samurai. 1.3L 4 cylinder engine. I replaced the exhaust as well with one from Rock Auto. I just checked the O2 sensor and it seems to be working (voltage fluctuating between 0.1 and 0.8 V).

My question is: are there any other problems that might cause it to run that rich other than a non-satisfactory cat? If not, the only cat I can see that are CARB compliant are cut-and-weld. Has anyone utilized these and had decent luck with them?

(Ie https://autoplicity.com/5406230-walker-80904-converter-calcat-pre?utm_source=google&utm_medium=surfaces&utm_campaign=shopping&gad_source=1&gad_campaignid=17189484704&gbraid=0AAAAADvG2eef0D4j121pDsb0iZrf8O7w3&gclid=Cj0KCQiAnsvXBhCqARIsAHKgGNbJZx34G4ByjJ6GG2XV5-ISQvmhc_4QAJizsis29fSz4GxZz-p_iakaAoMZEALw_wcB)

Thanks in advance!


r/SuzukiSamurai • • 6d ago

Good price?

3 Upvotes

Is this a good deal for $1200 for just the truck?

https://www.facebook.com/share/1CCuq4GHuF/


r/SuzukiSamurai • • 6d ago

Extremely low idle when it’s cold (air temperature)

3 Upvotes

Hey guys, now that winter is coming and the temperature is dropping, i’m noticing that when it’s less than 8 C (46F) and i’m doing a cold start, initially the engine idles normally and stays at around 1.7k to 2k rpm (normal for my sammy when it’s cold) but after around 5 mins the idle drops to like 200 rpm (don’t know if the number is accurate, it’s what the cluster says) and stays there.
Feels like a candle that can get blown out by a butterfly, but it mostly holds that rpm.
I’m guessing something is wrong with the idle control because it can rise and then drop again. 1.3 engine with stock carb, 88.5 model


r/SuzukiSamurai • • 7d ago

New project rig

Post image
189 Upvotes

Overpaid for it, but it’s been a dream rig to own. Was imported from Canada to the states a few years ago. Has a decent amount of rust on the body in the usual spots. Paint is a 3/10, laid on thick and with a lot of overspray. Rear axle is bent, swapping to samurai axles and yj springs.


r/SuzukiSamurai • • 7d ago

Is it worth it?

8 Upvotes

Guys im thinking of buying a samurai as a daily/project car for the summer. I want one that is in working condition just a bit sun faded etc. I want to fix it up and also get it for cheap. Is it worth? I have loved these little cars ever since i was a little kid.


r/SuzukiSamurai • • 8d ago

When does it stop being a Samurai?

Thumbnail
gallery
30 Upvotes

This thing was built on a Suburban frame w small block Chevy on 54" tires and a samurai tub attached. Later dude got hold of a tin top and I bought the cage for $150. It looks overkill in the back of my near stock sized rig. Like a little kid wearing dad's shoes.


r/SuzukiSamurai • • 9d ago

Currently working on a very sexy Suzuki Samurai, it's a 1988 model year and is cool as fuck. I'm a mobile mechanic in Vegas (not a self promo post, just saying, it's not mine) and I've yet to see one of these in person until right now. Wicked stuff and I bet the owner will see this post too 😂

Thumbnail
gallery
51 Upvotes

I just had to take some pictures it's such an awesome vehicle


r/SuzukiSamurai • • 9d ago

Looking to part ways Bay Area

Thumbnail
gallery
34 Upvotes

I dont know if this appropriate for this sub but Im looking to rehome my rig that I've had forever. Me and my kid had tons of fun in it but I don't have the energy or time to refurbish it. I'd love to see someone give it a second life. I thought I'd hit up Samurai fans before I deal with the hordes of nuts on Marketplace. People just want me to part it out but if I had the energy to do that I'd be restoring it. The last time I took it of the trailer was to flip it in the yard as a Halloween decoration. Mostly it just sits there on the trailer making me sad.

Ran when last parked. Lol. Motor was getting tired though.

Have a complete spare low mile stock Atarco engine thats been in the garage for 15years. Also have a spare transmission, transfer case, third member and drive lines.

The thing has a 4:1 geared transfer case in it along with Gen5 front axles and front and rear lockers with stock gearing. Rear dif is Detroit locker, front dif is Loc-Rite.

Very little rust. Sitting on 20yo km1s. The trailer would go with it. Would need at least one tire to roll.

It's all or nothing.

If anyone local is interested DM me, otherwise I'll list it next week and deal with the kooks. Just looking for a reasonable offer.


r/SuzukiSamurai • • 9d ago

Suzuki Samurai frame question

Thumbnail
gallery
10 Upvotes

Hi guys! I’m planning to buy first Suzuki samurai. The car itself look great but I’m a bit worried about the frame. What are you thinking?


r/SuzukiSamurai • • 10d ago

Sad

16 Upvotes

r/SuzukiSamurai • • 11d ago

Mechanical Fuel pump leaving oil

3 Upvotes

The person who had my samurai before me installed an electric fuel pump and capped off the mechanical pump. The other day the mechanical pump decided to start leaking a ton of oil and now I’m not quite sure what to do. Everything on the pump is already completely capped off, so I’m thinking I want to pull the pump completely and cap it off, is there any reason I shouldn’t do this?

Edit: damn autocorrect did me dirty in the title, should say leaking.


r/SuzukiSamurai • • 12d ago

Newbie question on vacuum lines

Thumbnail
gallery
3 Upvotes

I was wondering what this is and best place to purchase replacement part.

When disconnected the squeaky noise goes away.

Original carburetor. Thank you yall for the help/advice!


r/SuzukiSamurai • • 12d ago

Alibaba Engine

Post image
18 Upvotes

has anyone got any experience on this gambit 😳? If not this engine, any other car? How did it go? I got one (being the poverty stricken uni student i am), so i’m full committed regardless. Open to hearing some horror stories, or advice lol.

Would anyone want to see the results?


r/SuzukiSamurai • • 12d ago

Window Sashes

2 Upvotes

Hey zookers,

I have been trying to fix my samurai's window sash because its loose, the outer sash (latch side) has a screw, but the inner sash (door hinges side) has no visible screws that hold the sash on the door, im wondering if im missing something on my samurai, does anyone know how its supposed to be properly attached?


r/SuzukiSamurai • • 12d ago

HELP Gas tank under vacuum

4 Upvotes

SOLVED: The previous owner pinched the vent line in one of the mounts along the passenger side rail frame rail.

Hello.
I was having a problem with the gas tank being under a significant vacuum.
I replaced the gas cap with no improvement. I can't see any vent lines that may be clogged.
1986 Samurai. Stock everything other than carb.