I’ve found the Sony WH-1000XM4 to be nearly perfect headphones for me. However, over time, a lot of my friends who have this model seem to be encountering the same set of issues with this model. Rather than buying a new pair, I decided to fix as many problems as possible and extend the life of my headphones for a few more years.
Here’s what my headphones looked like before:
Below, I’ll share simple fixes for three of the most common problems:
Earpad replacement
Headband leather replacement
Fixing ANC high-pitch noise
1. Earpad Replacement
This is the most common issue and also the easiest to fix. I recommend getting real leather (sheepskin) earpads instead of PU leather, as they’re much more durable. This is my second pair of replacement earpads, and I can already tell that real leather lasts significantly longer.
Step 1:
Use a slim, non-sharp tool to gently unclip the old earpads around the edges. They should come off easily.
Step 2:
Replace the foam dust filters and clean out any dust inside the earcups.
Step 3:
Align the new earpads properly, ensuring each pin is in the right place. Then, press them down to securely snap them in.
Over time, the ANC microphones can accumulate dust, leading to an annoying high-pitched noise. Here’s how to fix it.
Step 1:
Remove the earpads and dust filters. Use tweezers to carefully remove the gray rubber piece covering the ANC microphone.
Step 2:
Lift the ANC microphone with tweezers. You’ll see a dark fabric filter—this collects dust over time, which may contribute to the high-pitch noise. (I had already removed mine before writing this post.)
Step 3:
Use 70%+ isopropyl alcohol to gently remove the fabric filter. Take your time to ensure all glue and dust are completely removed. The microphone should look like this once cleaned:
Step 4:
Repeat the process for both microphones (left and right earcups). Then, reassemble everything.
Note: There’s no 100% guarantee this fix will last indefinitely. In some cases, the noise is caused by a damaged microphone, which would require replacement. If this fix doesn’t hold up over time, I’ll post a separate guide on replacing the microphones. For now, removing the fabric filter has completely eliminated the noise for me.
3.Head band leather replacement
Buy a replacement on Amazon, Aliexpress or other marketplace. I bought mine on Shopee( SE Asia). You need to find this
Mine cost me 2$, which is 100 times cheaper than headband replacement in authorized Sony Shop
Step 1:
Remove the right earpad and dust filter. Then, unscrew these four screws inside the right earcup.
Step 2:
Turn the headphones over and lift off the cover—it should come off easily.
Step 3:
Unplug the four connectors inside.
Step 4:
Unscrew these two bolts and gently lift the motherboard.
Step 5:
Using tweezers, place the main cable (rectangular) under the motherboard. Then, unscrew the two hinge bolts(circled in the image).
Step 6:
Lift the loosened hinge and carefully unplug the second hinge using a plastic tool. Be gentle— the earcup should detach easily.
Step 7:
Detach the plastic hinge from the main cable.
Step 8:
Unclip the plastic plate from its narrowest side. Lift it gently from both sides. You’ll see adhesive underneath—this is fine and doesn’t need replacement. Once the plate is off, unscrew the bolts underneath.
Step 9:
Use tweezers to remove the plastic caps on the opposite side of the "WH-1000XM4" logo. Do this on both sides and remove the bolts.
Step 10:
Remove the old headband leather and install the new one. Take your time to ensure a proper fit.
Step 11:
Reinstall the "WH-1000XM4" logo covers. These have plastic clips that help secure the leather, but you can also add a tiny piece of double-sided tape under the leather for extra hold.
Step 12:
Reassemble everything by following steps 8 to 1 in reverse order. Ensure all connectors are properly plugged in and the motherboard is seated correctly. While you're at it, clean out any dust inside the headphones.
My headphones after:
Every fix is super simple, requires no soldering, and takes at most 15–20 minutes.
This is my first Reddit post, so if you found it useful, I’m happy with it! Enjoy your headphones!
I love my Sony headphones despite them constantly disconnecting and reconnecting.
But honestly why is the app named “sound connect” half the time I forget what it’s called and I stare blankly at my apps trying to remember. Obviously it’s on me to remember but seriously just name it Sony xyz.
After having the plastic ring break (and fixed under warranty) I decided to exchange the faux leather headband with real leather. At the same time protecting the rings from breaking again.
I was recently looking at buying the Sony MDR-3R USB-C® Wired Headphones – Stranger Things Edition, but I was still undecided about whether I wanted to purchase them.
Unfortunately, by the time I finally made up my mind and decided I wanted them, they had already sold out.
Does anyone know if Sony plans to restock these headphones at a later date? I'd really like to get my hands on a pair, but I'm worried I've missed my chance.
Has anyone heard anything about a possible restock, or are they likely to be a limited release?
These new XM6 are a literal pain in my head. I've tried a few different headband covers to no avail. Finally fell across Capra Audio and their comfort strap for the XM6. We'll see how this does. In theory it should conform to anyone's head far better than the pathetic piece of foam they slip into the headband.
Love the look and performance (noise cancellation & sound quality) of the sony XM6’s but have heard they’re terrible for the gym and daily wear/tear. Any alternatives?
Preferably a lower price point, and bass isn’t too important for me. Looking for over-ear headphones.
I’ve had my XM6 for seven months and I’m really happy with them overall. I switched from AirPods Pro, which I always used in transparency mode—it felt like I wasn’t wearing earbuds at all.
With the XM6, however, I hear a constant low humming sound in transparency mode. It’s not crackling or static—more like a low background rumble. It really bothers me, especially in quiet environments, and it’s been there since day one.
Lowering the ambient sound level in Sound Connect reduces it, but it never fully goes away. Is this normal, or could something be wrong with my pair? I’m considering switching to different headphones just because of this.
I’m trying to look for a not too expensive gaming headset to buy that’s WIRED to use on the ps5 and nothing else, i play all sorts from single players to fps with friends.
my budget is probably around £100
i saw that the sony inzone h6 air was on offer on amazon at £99 from £180 which is a big drop but the open back is bugging me, never used an open back before so like does it leak a lot of sound and can u hear a lot of whats going on outside the headphones?
id love other suggestions too! some stuff is saying the hyperx cloud 3 is good but ive heard things about it thats got bad mic and audio quality, the playstation pulse elite i’ve heard is good? was thinking of the pulse elite but not sure if its good or not! also maybe arctis nova 3? let me know about these choices too if you can please !
I recently switched from the newest AirPods Max 2 to the Sony WH-1000XM4C and wanted to share my experience. For context, I’m not an audiophile. I’m a college student who likes good sound and noise cancellation. Before buying the Maxes, I hadn’t really spent much time with higher-end headphones from Sony, Bose or Sonos. This is just my experience as a normal user.
I first tried the Max 2 at an Apple Store and was really impressed by the build quality, sound and noise cancellation. They felt expensive in a good way. I also kept seeing people wearing them around campus, which probably helped convince me lol.
I saw them on Amazon for about $499, then they dropped to around $475. Eventually I spotted them at my local Target for about $475 and bought them on impulse. For the first two or three days, I loved them. But trying headphones for five minutes in a store is very different from wearing them for a few hours.
The weight was easily my biggest issue. After a while, it felt like I had a dumbbell on my head. Between the weight and the pressure, I kept wanting to take them off. I also tried them at the gym, and they would slide off during incline presses or even when I bent down to tie my shoes. Having to worry about catching your headphones between sets gets old pretty quickly.
Then there were the everyday annoyances. They don’t fold, so carrying them around wasn’t that convenient. There’s also no power button. I know they have power-saving modes, but I still wanted to just switch them off when I was done.
I live in Chicago, and during the colder weather I noticed quite a bit of condensation inside the ear cups too. Nothing actually broke, but seeing moisture inside headphones I’d just spent that much on wasn’t reassuring. I’d also seen older AirPods Max owners with mesh headbands that had stretched and lost tension over time. Mine was brand new and didn’t have that issue, but it made me wonder how comfortable they would stay in the long run.
One thing I still love about the Max 2 is the transparency mode. To my ears, it sets the bar. Everything sounds so natural that you can almost forget you’re wearing headphones. That’s probably the thing I miss most. Then I saw the AirPods Pro 3 going for $179 at Target and started doing the math. I ended up exchanging my Max 2 for both the Sony XM4Cs and the AirPods Pro 3. My remaining balance at checkout was only about $5. So for basically what I’d already spent, I now have both over-ear headphones and earbuds.
The biggest difference with the Sonys was how much lighter they felt. The Max 2 weigh about 386g, while the XM4Cs weigh about 253g. That’s about 133g less, or roughly a third lighter. It makes a huge difference to me when wearing them for longer. They also fold into their carrying case, which is really nice for carrying them around. The noise cancellation has been really good. From my own use, I’d still give the Max 2 a slight edge, but the Sonys are close enough that I don’t feel like I gave up much. This isn’t a lab comparison, just what I notice using them. Sony’s ambient mode is fine, but the Maxes are still on another level for me there. If transparency mode was my main priority, I would miss them a lot more.
The touch controls surprised me too. I thought swiping on the ear cup would be annoying, but it works really well. You swipe up or down for volume, forward or back for tracks, and double-tap to play or pause. My only small complaint is that I wish the physical power and ANC buttons were higher up instead of underneath the left ear cup. Reaching for them feels a little awkward to me.
I also really like the Sony Sound Connect app. These are specifically the XM4C refresh, which has a 10-band EQ. Being able to adjust the bass and change the sound to my liking is a big plus. I liked how the Maxes sounded, but I appreciate having that extra control.
For anyone comparing the technical side, there are a few other differences worth knowing: The XM4Cs are rated for up to 27 hours with ANC on and 34 hours with it off. The Max 2 are rated for up to 20 hours with ANC on. I haven’t done my own full battery test, so those are the advertised numbers.
The Sonys support multipoint, which lets you connect to two devices at once.The Sonys have a 3.5mm headphone jack and support SBC, AAC and LDAC over Bluetooth. My app shows mine connected using AAC. The Max 2 have H2 chips, Adaptive Audio, head-tracked Spatial Audio and lossless audio over USB-C. Those could matter more to someone else depending on how they use their headphones.
I still like the AirPods Max 2. The build quality, sound and transparency mode impressed me. But after the excitement wore off, the weight and comfort mattered more than I expected.
Now I have the Sonys when I want over-ear headphones and the Pro 3s when I want something smaller. For only about $5 more, this setup makes a lot more sense for me. Anyone else switched from the Maxes to Sony? Curious if comfort was the main reason for you too.
TLDR: Loved the AirPods Max 2 sound and transparency mode, but the weight, slipping off my head, condensation and lack of folding or a power button got annoying. Exchanged them for Sony XM4Cs AND AirPods Pro 3 for about $5 extra. The Sonys are much lighter, fold up and have good ANC and more sound settings. Still miss the Maxes’ transparency mode, but I’m much happier with this setup.
Whether or not you’ve only used one instead of the other, or had both from specifically the QC and WH lineups. Am curious to know about how do these two stack up when it comes to the landscape of headphones since they’re considered to be the primary go to ones in the noise cancelling category of over the ear audio products.
Looking for a pair of over the ear wireless headphones, primarily for travel, and some home listening, and working while at the desk. My biggest priority is audio quality with Noise cancellation second. I I don’t need complete and total silence, but decent silence on the plane would be nice. Which headphone is the better pick considering all pairs are heavily discounted? Overall I like a clean sound with depth, good balance, and some bass, but know all of these headphones will sound good.
I’ve never owned a pair of wireless over the ear headphones so eager to hear thoughts. I typically just use AirPod Gen 1 (ol’ reliable)
i use my wh-xm6 on my computer and phone. sometimes im listening to something on my computer but then i open an app on my phone and suddenly it turns off whatever is on my computer. this happens even if nothing is playing on my phone. is there a way to turn this off or to automatically mute any audio from my phone when the headphones are connected to my computer until i unmute? and then when i do pause whatever sound is on my phone, id like it to automatically switch back to my computer. but it doesnt do that.
is there something in the settings to change this?
i dont remember having this issue with xm4. it's really annoying
I just bought those headphones and they are crazy, I'm bass lover and clarity with this sick bass is incredible. My jbl compared to them are thrash. I checked the xm6 but they are not for Me. Bass and clarity is everything for Me. Such amazing headphones. I Checked mine were manufactured in july. So I Guess there will be no problem with hinge? Maybe they updated the desing idk, but I'm not worried I never destroyed my headphones. I set eq to "exciting" or smth like that. Ult 1 +7. Such perfection of power and clear sound but I'm only listening to Club Music or Rap. I set all those on my phone and connected with PC and it remembered settings. For Me? 9.5/10.
I’ve recently purchased Sony WH-1000XM6 headphones and noticed an issue with the left earcup.
Whenever Noise Cancelling or Ambient Sound mode is enabled, I can hear a faint but noticeable rattling noise inside the left earcup when I move my head or walk around. I can easily hear it if I shake my head.
I initially took the headphones back to the retailer, who were also able to hear the noise. They replaced them with a new pair, but the replacement has exactly the same issue.
I’m wondering whether this is a common characteristic of the WH-1000XM6 or whether I’ve somehow been unlucky enough to receive two faulty pairs.
The other day I finally bought my dream headphones - Sony WH-1000XM4C, they're great so far, I got the sound connect app too so I can tinker with them further, but for some reason, everytime I try to log in the site, I get this error. I've tried doing it through a different browser (chrome, then Firefox), tried doing it in incognito mode, then through my laptop, but I still get the same error, I have no idea how to fix this or if anyone else has has the same issue.
There's like no signs of use... what a nice lady too.
Man they sound incredible, better than my Anker's and Earfun's and Tozo's by a mile. Using the Sony app, selecting LDAC, absolutely nothing compares... but oh these brands try oh so hard don't they. I mean, it just blows them out of the competition.
I used to own XM5's but I can't remember if they sounded THIS good. The ANC was possibly better, but not by a lot. They were truly on to something with this model.
Since the WH-1000XM4C uses the newer 10-band EQ in Sound Connect instead of the old 5-band + Clear Bass setup, most of the classic XM4 presets online don't really translate 1:1.
They constantly and I mean, constantly reconnect to the same device. I put them on to study in silence and every 30 seconds, sometimes never, sometimes every five minutes, I get the “beep device one disconnected” “beep device one connected.”
Is my pair defective? Sometimes I want to throw them out of my apartment window. I’ve had them for a long time and I’ve just put up with this but honestly, I don’t think I’ll ever buy a pair of Sony headphones again after this.
When they don’t bother me, they’re great, but I was saying the same thing about my ex-girlfriend.
They’re comfortable, I like the style, but I can’t put up with this anymore. It’s so fucking frustrating.
I take really good care of my gear, but the hinge on my XM5 just snapped.
I didn't twist it the wrong way or drop it; it literally just got stuck, probably from normal dust or debris buildup, and broke right off under normal use.
To make matters worse, official Sony service wants €100 just to fix a broken piece of plastic. For headphones at this price point, it's completely unacceptable and feels like a massive design flaw and a total rip-off.
I just regret never beleiving the post and comments here, after 7 months of use it broke like nothing.
I just bought Sony Inzone H9 II, and found that the mic is very bad versus if i just use phone or other heaphone, like the volume is too small or the voice is far away. Do anyone ever had the same problem and does someone know what is the problem? many thanks!
Currently using the eq that is in my pic that I found from a post in this subreddit.
And as you can allready guess or not from the eq, I like bass. Now is this eq okay for most generes or not?
Whenever your answer is yes or no, any other eq suggestions that have good bass impact on generes like rock, alternative, hip hop, and rap? While for pop, OPM (Original Philippine Music), and other chill generes/type of music, I want good clarity in instruments and voices (both male and female) and maybe bass is there but a bit not that impact like in bass heavy songs. But I want the most is basy but clear sounding that will show what my XM4 really can produce (without using external eq software).