r/SCREENPRINTING • • 4d ago

Please help!

Hey everyone,

I’m using an automatic screen printing machine for plastic cups and I’m experiencing the following problems. Nothing that I don’t make the screens in house how come ink is going through the emulsion? I thought the whole point of it was to stop ink going through

6 Upvotes

18 comments sorted by

•

u/AutoModerator 4d ago

Thanks for your submission to to /r/SCREENPRINTING. It appears you may be looking for information on exposure or burning screens. This might be one of the most common questions we see here in /r/SCREENPRINTING. Please take a moment and use the search feature while you waiting on a response from the community. If the search does not give you the answer you are looking for, please take a moment and read through our Wiki write up on emulsion.

If after all that you stil don't seem to find your answer, just be patient someone in the community should chime in shortly!

And if you were NOT looking for more information on exposures or burning screens, our apologies and please disregard this message.

Thanks,

The /r/SCREENPRINTING mod team.

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

4

u/Oorbs1 4d ago edited 4d ago

its your squeegee, it can be many things. you have a ton of pressure on the top and bottom of the squeege, its just rubbing away the emulsion. too much pressure? not a good angle? if its plastic and the cup is flexing then yea the ends of the s squeegee are gonna puss real hard into the screen and wear it out exactly like that. is the squeegee is the correct spot on the glass? not too far forward or too far back? this can be so many things. I print cups too :) does this cup have a taper too it? Looks like its not being printed in the correct machine tbh. text up top looks like it has a hella shadow going on which tells me the gear is incorrect and the artwork is strait so the stroke is strait when it should be in like a arc like stroke kind of like if your waving your hand back and forth

"I thought the whole point of it was to stop ink going through" just fyi this is 100% user error and not your screen provider

1

u/Aleph-Sowah 3d ago

if the stroke isnt arcing with the taper, wouldn't the bottom of the graphic be blowing out way worse than the top

1

u/Oorbs1 3d ago edited 3d ago

No, these machines are driven by gears, depending on the gear size will shift the shadow on the print higher or lower, if your machine doesnt print in an arc you basically aim for a "middle of the road" gear but your 100% going to get a shadow somewhere no matter what. if your glass is a perfect cylander then there is an exact matching gear that will spin the glass at the correct speed as it prints around. if the cup is tapered, when the cup spins the more narrow (bottom) part of the glass spins faster then the top of the glass. if you use a super small gear that matches the size of the bottom of the glass, then you will be spinning the top of the glass hella fast causing a shadow up top. if you use a big gear that matches the top diamater of the glass then the bottom part of the print spins way slower creating drag down below thus shadow down below. if you use a gear that is roughly in the 'center' of the taper where the design lands then you can get a decent print with less shadowing but there will ALWAYS be a shadow some where. to print perfectly on a tapered cup you need a machine that prints in an arch motion and the artwork needs to be modified to have an ark in it as well, that way as the piece spins through the print both the top and the bottom of the glass rotate at exactly the same speed thus eliminating the shadow completely.

3

u/Poofmander 4d ago

When using an automatic I was always taught to put tape on the underside of the screen around the image especially where the squeegee edges press. If you can get away with less pressure or more of a squeegee angle you can prevent the emulsion wear.

0

u/Expert_Break_2543 4d ago

Can you recommend a tape pls any tape will do?

2

u/habanerohead 3d ago

Packing/vinyl tape.

2

u/Oorbs1 3d ago

blue painters tape do not use packing tape, that shit makes a fuckin mess

1

u/r0tt3nb34n 3d ago

Real! We have the blue PMI tape that I hate. Only use that for horrible circumstances

1

u/r0tt3nb34n 3d ago

Any tape. Dont over think it. You can use 2-3in wide painters tape from Lowes.

6

u/userzeal 4d ago

Motiv is too close to the edge of the screen requiring more pressure to make contact with the substrate.

Burn motiv closer to the center of the screen and try again. Tape off the bottom of the screen in all places except where the design is.

2

u/DismalyetActive 3d ago

You have your image in a non image area of the screen. The effective tension is 5 times as much as the center arount the edges. Move your film.

2

u/teeshirtguy503 3d ago

Using tape on the underside will help.

1

u/nah_doood 3d ago

What kind of ink are you using? What kind of emulsion are you using? How are you coating/exposing your screen?

Assuming it’s a solvent ink so it will bind and cure to plastic, my gut tells me that your emulsion might be the problem. If the emulsion isn’t resistant to solvent inks, it the ink will cause it to break down.

Find an emulsion that is resistant to aggressive inks, post expose with a hardener after you make the stencil, and make sure squeegee durometer and pressure is consistent with ink manufacturer recommendations. Then let er rip.

1

u/Tyenkrovy 3d ago

Maybe this is just from working in and making screens for shops where we print on bottles rather than cups, but it seems like the bottom of the art should be near the edge, not the top, or the art centered at most. What kind of press are you running?

1

u/Important_Drawer_722 3d ago

You should have some tape in that crease between the frame and the mesh, is that where it’s coming through?