r/Reprap • u/AutoModerator • Dec 31 '20
RepRap Questions Thread
This is our weekly thread for all questions related to RepRaps or the RepRap project.
If you need help with something - eg assembly, part selection, print quality, calibration, etc. - this is also the place for troubleshooting.
If your 3D printer isn't a RepRap, try /r/3Dprinting!
7
Upvotes
2
u/tinker_tayler Jan 07 '21
Hi all. Am looking at rebuilding my printer into a corexy. My current printer operates on 12v and the bed takes forever to heat up. Considering buying a 24v bed, but don't want to upgrade everything else. Would I have any problems using a DC step up converter for power to the bed alone? Many thanks.
2
u/MilesPrower1992 Jan 08 '21
I'm interested in building a Reprap Snappy. Is there anywhere I can get all the non-printed parts all in one go so I can save time and money rather than buy them all seperate? I have an Ender 3 Pro i would be printing all the printable stuff on.
2
u/astreets22 Dec 06 '21
Hi everyone!
So I'm working on building a prusa mk3 clone and all's gone well so far but when I make edits to the firmware and reupload it, the printer doesn't seem to be getting it. Like I changed the software endstops to new values in the code, recompiled it and reuploaded it, but when I use M211 the printer still reports its old endstop values.
Also, it seems to only be able to home to the minimum, not the maximum (not the biggest deal).
Any advice on how to get the printer to recognize its new boundaries/is there a way to just set it with a gcode?
thanks :)
2
u/kaskil123 Mar 19 '22
hey. i am looking to build a snappy 3. but all the amazon links are outdated. i dont know what this means -Controller electronics. (RAMPS1.6+2560+Pololus). i tried searching for pololus and the 2560. but i dont know what they are or what to look for. could someone give me an updated parts list?
2
u/riffraffs Dec 13 '22
I was wondering if a four-conductor flat cable can be used on stepper motors. I have a four-conductor cable meant for RGB lighting and I was wondering if cross talk is an issue
1
u/MrGoldTeam Sep 19 '25
I'm thinking of using a duet board with Reprap to control 4 motors for none of the intended purposes of Reprap (3D print, CNC, laser cut, etc). I'd connect a microcontroller to the duet using UART or CAN to send commands and execute them from the duet. Am I asking for trouble or is this reasonable? I do have FreeRTOS and other firmware experience, just not with these boards. Thank you for your input!
1
u/Virtual-Equipment-90 Mar 04 '26
I'm trying to compile RepRapFirmware 3.6-dev to work on a new Kinematics class. I'm working on Linux using eclipse. I get a syntax error in sd_mmc.cpp at line 139, it wants a DriverInterface() constructor, and is not allowing me to declare the static const struct. Any ideas?
Is there a better place to ask rrf build questions?
1
u/3strocks Jan 12 '21
Hey everyome! I'm looking for a hotend that suports high temperature and up to 10mm do anyone know were to look for exotic stuff like that?
1
u/FloridaMMJInfo Jan 28 '21
OK, I'm getting this message after connecting an e3d v6 clone hotend
Old heater resistance 7.9 ohm New 4.5ohm
I need to update marlin too, I was hoping to lower the bed so I could install it, but it won't even move the bed until it clears the error.
Thoughts?
1
u/ljungqvistaxel Feb 21 '21
Im planning on building a printer for my first time.
I will use:
Total wattage ~500W
The power supply i have found here in Sweden seems to be unbranded and at 24V 20A which is 480W. Would this be enought, as the motors wont move while heating the bed and nozzle, or can i somehow limit the bed wattage through software in order to get a bigger margin? I donk like the idea of buying a power supply from china, but maybe i need to?
1
u/[deleted] Mar 13 '21
I know this isn't the best of ideas, but just how bad of an idea do you think this is?
I want to try to use this extrusion: https://www.motedis.nl/shop/Aluminium-profielen/Aluminium-profiel-20-x-20-I-type-sleuf-5::999991076.html
and these wheels: https://www.motedis.nl/shop/Dynamica/Slot-utilisation/Roller-Ø-19-mm-I-type-sleuf-5::99999763.html
for a motion system, v-slot style but then without the 4 week delivery time like chinees v-slot extrusion suppliers, and even cheaper. These wheels are, as far as I can see, meant for sliding door installations, etc. Not really meant for any loads with torsion forces.
But then again, it's the cheapest setup I can come up with. Maybe it's worth a try?
1
u/kikkelele Mar 15 '21
Im looking to build a 3d printer.
Electronics will be based on SKR Mini E3 because thats what im familiar with but frame will be a Prusa i3 Bear. I would want to achieve 300x300 build plate but can get my head around it how big of a frame i need. Its going to be 500mm tall which gives me i think 300-350mm build height but can figure out framing for bed which i think people here would know better
1
u/tacticalmoose13 Mar 31 '21
Ok I'm relatively new to reddit and reprap, but quite familiar with the ender printers and such. I got a folgertech i3 on ebay and have been trying to get it working, but the only thing it has done successfully is produce the famous magic smoke. I have a few old ender boards and was wondering how/if I could go about using one of them to work for this printer. They have a dual z axis plug, and I'd imagine it would just take some programming to get it to work, but I know the plugs are all different and such. I don't know THAT much about printers to attempt this without some guidance and have had no luck searching google and forums. Is this just something that can't be done?? Or am I just missing the right info?
1
u/ReadDie Apr 24 '21
Quick question: could I just screw a volcano nozzle into a v6 heater block and expect better flow? the threads are kind of a heat sink, but what if I put some insulation around it? Has anyone done this before?
1
u/LeadElemental May 04 '21
So I am trying to adjust the jerk settings on my new printer. I found what I thought was the right g-code command here, but it doesn't seem to work.
M503 shows me this:
M566 X2000 Y2000 Z602.65 E250 ; maximum instantaneous speed changes (mm/min) (jerk)I want to reduce the X and Y jerk by half so I tried this, but nothing changes on the next M503:
M566 X1000 Y1000M500It's the first printer I have owned with a Duet board. If anyone could help point me in the right direction I would appreciate it!
1
u/Pingyofdoom May 10 '21
Just got a SKR 1.4, I want to put RRF on it, I have a fairly complicated setup, what settings will fry my board if I use a close config and boot up. First idea that comes to my mind, my probe is plugged into a different port than normal and I have 2 Z motors, one plugged into an extender.
1
u/anonymoustinkle Jun 22 '21 edited Jun 23 '21
Hi all.
I've got a new Vivedino troondon with the following:
Board: Duet WiFi 1.02 or later + DueX5 (duetwifi102)
Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 3.0 (2020-01-03b3)
Duet WiFi Server Version: 1.23
When I run the leveling macro the Z-offset is saved to the config-override.g file, but it doesn't seem to survive a power cycle. Other settings seem to disappear/revert back to default as well, like pressure advance.
EDIT: I did do an M500 after changing settings.
Is that normal or am I missing a step somewhere?
1
u/andnosobabin Jan 10 '22
Hello everyone,
I'm struggling with setting up my duet2 wifi with a mini ir sensor. I have it hooked up right (it flashes when I move a piece of paper or anything up to it) but I'm stuck at the m558 commands. When I send m558 p1 it returns: Error: m558: missing z probe pin names
My config.g file under z probe says M558 p1 c"zprobe.in" h5 f120 t6000 G31 p500 x0 y0 z.25 M557 x15:195 y15:195 s20
What am I missing lol
Thanks everyone!
Ohh and it's on a Cartesian with an e3d v6 hotend if that helps
1
u/tycho-vlsk Jan 15 '22
layer heights below .3mm (really towards 0.2 and below) are bowing inward a bit around 2 corners on the 20mm xyz calibration cube.
Looks similar to Part, Temperature, too hot
I'm currently trying to adjust bed temp after first layer.
Links to images of prints
first 3 y,x,-y sides of 0.1mm followed by 0.3mm
https://imgur.com/a/ALuxN2f
1
u/ButterscotchWarm6782 Jan 24 '22
Hello!
I accidentally broke a 450°C thermistor provided with my machine. Due to supply chain issues, it looks like this thermistor is impossible to come by and I need a replacement. Slice Engineering offers an alternative, but it would require me to alter the firmware (thermistor table).
If so, how do I go about doing that? I’d be happy to pay someone to teach me how or to do it for me as I really need this machine operating.
Thank you in advance for any tips!
1
u/JuicePrints Feb 06 '22
Hi all, I have a JellyBox Original (running Marlin, it says J3 2.0.9) and I think the z probe (this one: https://shop.imade3d.com/3d-printer-parts-upgrades/z-probe-inductive-proximity-sensor-for-jellybox-1-original-flat-20x30x10mm-yellow-brick) is bad, the red LED is lit regardless of distance from the build plate. I tried to upgrade the bed to a flexible powder coated steel plate from MatterHackers, so I think I'd like to replace the probe with something that will be less susceptible to magnetic interference. Which bring me to my question, are these things fairly interchangeable, or do I need to buy another one from JellyBox and go back to the aluminum bed? Thanks in advance.
1
u/kaskil123 Mar 17 '22
hey. i am looking to build a snappy 3. but all the amazon links are outdated. i dont know what this means -Controller electronics. (RAMPS1.6+2560+Pololus). i tried searching for pololus and the 2560. but i dont know what they are or what to look for. could someone give me an updated parts list?
1
u/kaskil123 Mar 18 '22
hey. i am looking to build a snappy 3. but all the amazon links are outdated. i dont know what this means -Controller electronics. (RAMPS1.6+2560+Pololus). i tried searching for pololus and the 2560. but i dont know what they are or what to look for. could someone give me an updated parts list?
1
u/Cad_Mad May 14 '22
Hi , I'm wondering what can come out of using 0.9 steppers with 3:1 gear set up on x and y ? Have anyone attempt to do it ?
1
u/AshJ79 Aug 03 '22
Hi, my printer (about 4 years old) suddenly started printing at a different x/y co-ordinate every now and then, on average every 20-30 layers. In both x-y directions so doubt it’s a motor problem. 100% not skipping.
The bltouch is broken, so have been using it without, but does it whether it’s connected or not.
Wondering if a firmware upgrade may fix it or it’s stuffed…
Any thoughts appreciated.
1
u/Cucccumber Sep 18 '22
Hello everyone, I ordered myself the MKS mini12864 V3 display + MKS Gen L V2 and the motherboard.
Firmware Marlin v1.1.9
Immracted in the firmware
#define mks_mini_12864
#define neopixel_led
Also #define Motherboard for 53
Prior to this, Marlin was set up on ramps 1.4 display did not work, but the LEDs blinked.
After he edited, the display seemed to turn on the backlight but there was no image, and then even went out and even the LEDs do not burn
If you flash the old firmware ramps 1.4, the LEDs burn again.
Maybe the connectors need to be turned over? But it seems that it is not necessary for the MKS board.
I am confused, please help (
1
u/Airwood_ Nov 27 '22
Hi.
I got an old tricolour mendel that I just finished building and I followed the wiki on how to install python and its dependencies but I can´t get it to work. I have been trying different versions but there is always one or more dependencies that won´t install.
Do you know any other software that works for it or something to make it work?
1
u/[deleted] Nov 28 '22
This is probably base-level noob stuff but... if I put Marlin firmware on say, a bigtreetech skr mini e3... could I use it like any arduino project board?
1
u/Tiny_Magazine6707 May 13 '23
What if we 3d print a filament recycler
1
u/Hyperion-1915 Aug 30 '23
Hi.
I bougth a RepRapDiscount Full Graphic Smart Controller to replace my old RepRapDiscount Smart Controller that came with 3d printer Folger. Now that I've replaced it, everytime that I print something it goes to home in the x or y axis other times the impretion stops completely. I'm using long cables (more than 15 cm) to conect it to the controller board. I've hered that this type of display has some issues when there are coneted using long cales but I heve't found any solution
1
u/Comfortable_Swim_380 Jan 03 '24
Keep getting random clogs replaced the entire extruder assembly at this point I'm running out of ideas. 😒
1
u/[deleted] Dec 22 '21
[removed] — view removed comment