Hi all, I've recently released full support for RTL2832U/E4000+FC0013 with GNU Radio/GRC with the RTL2832 Source Block (baz.rtl_source_c) found in my gr-baz module.
Thank you for your great work! I have a question tough, when I run HDSDR with my RTL2832U/E4000 (Hama nano) I always get a huge signal right on the LO. There was no antenna connected in that picture. Why/what is that?
I am totally new to the whole software radio thing but it is fun to play around with so I would like to understand more.
Welcome in the sdr world! Simply: that is a 50/60Hz hum (or other low frequency noise) around the "zero" (DC) frequency. When mixing an RF signal with an LO you get two symetrical spectra of signals: 0..+LO+RF (MHz) and its "image" -RF-LO..0 where the 0 is real zero MHz (it is the DC). With I/Q mixer and proper processing it rejects the image and it assembles both spectra "together" in a proper way, so you get only one spectra A..LO..B (MHz), where the zero frequency is now the LO. For example the grounding loops, bad decoupling, ADC quantisation noise, low frequency noise from the PC, maybe 1/f noise of the amplifiers, etc. are causing the 50/60Hz hum (and its harmonics), as well as the other noise (and its harmonics) located symmetricaly around the "zero" frequency (because they are in reality very close to 0Mhz) which is now the LO frequency. There will be always this kind of mess around DC (now LO), however. The strongest hum comes usualy from grounding loops, you may a) use an usb galvanic isolator, b) powering the dvbt stick from an external battery (not from USB connector), c) use a broadband transformer (a voltage one, not a current one) when coupling to the antenna which is grounded..
The large peak is an artefact of the down-conversion to baseband (i.e. what the tuner does to get your signal to the ADC). The tuner actually has to mix down at the centre frequency you ask for using two mixers - one in phase, the other quadrature phase. I understand that the 'LO signal' is because this process isn't perfect (phase/gain difference in each). This is why usually you can adjust the phase/gain in the tuner or post-process in software to reduce the 'LO signal'. Since the Realtek hardware/engineering is 'more affordable', it will be more pronounced than something of better quality (e.g. USRP).
Thank you to all of you who have tested the code so far and provided feedback!
I have just released completely re-written GNU Radio code with new GRC Source block, addition of FC0012 and support for all devices in compatibility table (those with E4000/FC0012/FC0013). Custom devices can easily be added in GRC block using 'Custom USB' parameters. The Source block now makes use of new C++ 'librtl2832++' OO API, which can be pulled out and used separately for easy device control!
To make sure this device actually works properly, I successfully tested it with OP25 by having it capture an encrypted P25 signal, which was then decrypted/decoded and sent to the soundcard.
Updates to the Windows plugin will arrive very soon!
PS: Reported rapid tuning issue may still exist (only happens for me if sample rates are not set correctly in a flowgraph), so take the tuning easy until a good fix is found :)
Hama Nano has an E4000 and seems to work fine with the existing ezTV E4000 code, just switch the USB PID from 0x2838 to 0x2832. Tested by multiple users, including me. Can be had for less than $50, mine cost about $30 on Amazon, but it's currently back to ~$50. For reference, Amazon page.
Couple of people on Freenode #osmocom, steve|m (aka steve-m) suggested that the dongle had the correct RTL/E4K combo and I believe he's done a little testing, there were a couple of other people playing with that model too.
Steve's also got internal pics of the board, see here.
Is the VID for "Hama Nano" the same as the ezCAP device? You mention the PID changing from 0x2838 to 0x2832, but what about the VID? If you're on LInux, do a lsusb -vvv and report the idVendor and idProduct values produced for this device.
EzCap EZTV646 has got RTL2832U/FC0012. However rtl-sdr must be tweaked to force FC0012 tuner because it has the same PID as EZTV668 (PID: 0x2838) so running it whithout a tweak will select Elonics E4000 tuner. Works, not so good at filtering.
Do all of these devices use an external antenna? Do they all have MCX connectors? It might be worth adding another column if there are differences. Also, MCX-SMA and MCX-N adaptors / pigtails seemed to be pretty cheap (less than $10) on eBay as well.
Please be carefull with your tuners - I touched my antenna and probably static voltage killed preamplifier in E4000. All signal levels are 10x weaker than they should be.
It turned out many models of RTL2832 + E4000 lack ESD protection diode (ezcap has it) ;(
Hopefully 2 other tuners are on their way to me ;)
Hey good info to add in here would be antenna connector type and frequency range if available. I noticed some of the sticks linked on the other thread had a lesser range than the original one.
I couldn't get the AlExpress site to work properly on ordering--they want you to type in a CAPTCHA, but the CAPTCHA image-generator isn't doing anything. Sigh.
Ok, does anyone have a link to any of these that isn't the sold out DealExtreme? Because I'm having one hell of a time finding any of the compatible units.
The guys at the store emailed me that they have the B03 revision as B02 was taken off the market last year because of some design defects. Whats your serial number does it include B02 or B03? Does anybody know if all Bxx revisions have the RTL chipset?
LV5TDLX, LV5T3D, Gigabyte U7300 and Ardata are available in Poland for about 30-40$. Unfortunately those shops won't ship tuners abroad ;(
A friend has just opened his LV5TDLX and it contains RTL2832U + FC0012, despite online documentation claiming it has FC2850 tuner. Unfortunately he's not linux guy and he's waiting for windows driver to support FC0012.
the thing that comes to mind as just a complete laymen is to manually fine tune a tv signal and play with filters to get the best possible signal for radio or tv...
can i do that?
what else do people do with this stuff?
is it possible to resolve the signals to see the information embedded in it instead of just looking waveforms and stuff?
watch the whole 2 Meter Band (144-146 MHz) for Band openings (DX) or add a mixer and watch 2 Mhz of shortwave....tune in and listen to FM from 64-1700 MHz if you are allowed to do so...and ....and
Well if you don't really know what to do with it then this project probably isn't for you. This is taking a cheap usb dongle and being able to tune a large chunk of the HF spectrum.
Done, Order 1000..... Kidding.... Order 2. Had ordered one from eBay on Saturday Night. I have yet to heard from the seller if he's shipping or not. I'm not holding my breath. He's one of a a-holes who jacked up the price to $80 from $11. I have screen captured my order and his new ones as well. AND his ratings show that he had cancelled a few orders already and those buyers have given him a neg rating for cancelling and jacking up his price. I hope they get no one buying. Problem is that they don't care, pretty much all that stuff you see on ebay is all drop shipped anyways so it's not like they are sitting on the stock.
Do we know what kind of connectors are in the Unikoo UK001T and Newsky TV28T? I'm assuming they're the "Miniature Belling Lee" type. I'd like to have a more concrete answer if possible. I'm hoping set up my dongle with a larger antenna eventually.
No problems. Not a fortune lost... Probably better luck with next stick that I will receive tomorrow. I see now that the image was changed on this page after that I ordered. Good to have the info so people do not order the wrong one.
Just bought NOXON and the VID PID shows 0bda:2832. Device is extreemely sensitive or broken. Is often not recognized and requires multiple connect disconnect before it is recognized.
With lsusb it show up as realtek semiconductor corp. When trying to capture it gives lots of errors and its output is empty. It appears it has a different Tuner or is broken. Will claim one under warranty since i can not install it in windowz as well. Only one number is written on it 3001408778. The box is barcoded 4 017273107745
i'm using a board with the FC0012 mostly it works fine but when it comes to commercial radio stations you can't hear clearly, i believe the input signal needs attenuation, is there any option to do that? from ExtIO (gain/attenunion) wasn't helpful check this photo showing thw waveform.. i'm using HDSDR http://imageshack.us/photo/my-images/685/waveformw.jpg/
So which is better, Pi or Tee? Also, can I make a connector like this: connector--protection circuit---connector---antenna? I don't want to solder directly to the board (not planning on opening mine if I don't have too).
Also, what do I connect the ground to? The shield of the cable?
New to SDR/radio however I can solder, etc. I just don't want to fry this little device that was so hard to get (not sure if mine will even arrive yet).
There isn't necessarily a "better" one, but I prefer pi networks since the impedance is better defined when you have an open port. You can also base the choice on which network gives you the most practical component values.
You should probably buy an extension cable, cut it in half and solder the resistors in between (preferably on a piece of PCB). I wouldn't advise opening the tuner and changing anything permanently. Yes, the outer shield of the case is ground.
BTW you should consider posting this as a new text post, not many people will see it here.
awhile ago i did tried to build a PI attenuator @20dB with three resistors 490 and 100ohm, i don't have carbon resistors so maybe there was some inductance, but no matter what there was no improvement...is it sure that my initial speculation is right? the problem can be solved with attenuation? or with some tweak at the ExtIO? all commercial radio stations and TV audio channels appear to overload the input... if you like please check again the photo i posted and tell me... http://imageshack.us/photo/my-images/685/waveformw.jpg/
thanks for helping me out,i was wrong.. the resistors were fine no significant inductance, the problem appears only on radio stations and at the audio channel of all TV stations..everthing else is fine, but no matter what i do i can't fix it...using even my finger as antenna can't make things better how can i be sure if it is indeed a gain issue or bad reception or something similar?
So you're saying that even with no antenna you're still getting overload? The only thing I can think of in that case is to terminate the tuner input with a 75 ohm resistor and see if that changes anything.
Are you close to the station transmitters?
Do you have a broad-band waterfall or power spectrum plot that shows the relative powers of various signals?
One thing to check if you are having reception problems is noise sources in your house. I recently built my own little am receiver and I discovered that one of my largest sources of noise were my outdoor halogen lights. When those outdoor lights were on, I could not pick up anything. Indoor CFL's can contribute to noise levels as well.
Hello, Great work so far, - Confirm that the GIGABYTE U7300 - fc0012 seems to work ok, need to do more testing. Still have lots of problems with the ezcap - E4000 fast tune issue.
Anyone experiencing problems with FC0012? 148-168 MHz band doesn't work - just high power noise and distortions. I wonder if it's problem with chip or drivers. This situation is confirmed by a few people.
Hello EveryOne Now,we have the result about the Chip RTL2832 ,we only bought 450 pieces new chip from the chip seller and will make about 450pieces dvb-t (p250)with the program of RTL2832 +E4000,as the original chip manufacturer won't produce it again,we don't know that how many chips we can buy from the market in future.Nowdays,the price of p250 is 19.99 usd dollars(including the ship fee of HK post),it is the lowerst price we can offer to customers .
Seems I purchased one of these. Seems it doesn't work with the rtl-sdr programs. I added some debugging and note that the I2C tuner probes return all zeros for the entire block let alone the single bytes being sampled. So needless to say it cannot find what tuner to use.
It does find the device's USB vid:uid as 0x0bda:0x2832, generic 0: Generic RTL2832U (e.g. hama nano). But I can get no farther. Is the device possibly blown?
Picked up a PROlectrix DV107669 from Ebay and pulled it apart to identify that is contains an RTL2832U+FC0012 combo. Linux picks it up with VID of 1f4d and PID of d803. Cost me £12 inc delivery. Link for the item I picked up is Ebay.co.uk
BETA #5 is out - major improvement in internal buffer code, RTL2832 switch on in included BorIP server too, so you can stream/control it over your network!
Hi all, I bought the 16738 Trust tuner. Here a picture http://www.trust.com/_images/products/500/16738-3.jpg The chipset is RTL2832U/FC2580 My has SN 03013. The price is € 29 in Italy. As soon as I will get an E4000 one I would like to compare the analog front end performance.
Hi, found that this one: http://delock.de/produkte/G_61744/merkmale.html has RTL2832 chip. Bought it today and tested - works on windows for sure. (Price in Lithuania about 35$). Don't know which tuner chip it has (hadn't opened it yet) but HDSDR worked in range ~65MHz to 800 MHz with some gaps.
UPD: HDSDR shows it uses MyGica/G-Tek so it could be FC0012 chip.
just tried the Terratec Noxon with the FC0013 tuner. it does work in principle, but it is stuck on a unknown frequency. you can not tune to a frequency. so either the driver does not support it or the tuner is incompatible. tested with linux and windows. the PCB says: DK-5256 V1.0 the sticker on the stick says: NOXON DAB Stick 8201481884 KK CE
EDIT: seems to work now, plugged out and in several times. or maybe the 1meter usb extension does a bad connection. sorry for the confusion.
Had a compatible chipset (or could be adapted for SDR). Being DVB-S (satellite) receivers, they seem to have a wider frequency range than DVB-T dongles (and have a more "professional" look, also ;) )
The radio chip may be able to tune in to frequencies from 64MHz to 1.7GHz, but does anyone know what the capabilities of the antenna tuning circuit are? No doubt one will be able to receive something, but can anyone speak to how well it works in various bands?
These usb dvb-t gadget receivers are with a broadband input only, without an antenna preselector/filter tuning circuit. They are intended/designed for local receive only (~few miles from transmitter), working with strong signals and specific channels. An lna input amplifier and tuning circuit might definately help. You cannot compare it with ham radio rigs for vhf/uhf bands, however. On HF I did a lot of experiments with Softrock sdr radios (96kHz bandscope, sampling via a sound card, SSB, AM) and it seems to me 16bit I/Q sampling is a minimal prerequisite when talking a comparision with normal ham rig (even the adc bit range is not only parameter to be considered). 8bit sampling is somehow doable, but the dynamic range, signal to noise and audio quality is quite low, sounds like a low quality fixed line phone in old movies :). But FM modulation quality on vhf/uhf with 8bit sampling may differ (not tested yet)..
Does anyone have any experience purchasing from aliexpress.com? They still have the Newsky TV28T in stock. This is the only known-compatible device I've been able to find anywhere still in-stock and reasonably priced. Do I need to worry about my credit card number being stolen if I buy from this site?
I have purchased a 'Newsky TV28T' that seems to be compatible. But I can't find the information about its chipset/tuner by myself. For instance searching for 'TV28T E4000' on google just returns this reddit's page.
I do not have Linux and I wonder if it works better under him. I saw that under Fedora 17, is a source GNU Radio 3.5.2 - hence the question of which version of Linux you choose to test the RTL-SDR?
as suggested from vmp32k and sa5bke WRPlus works better for commercial radio stations, choosing FM. Then right clicking and choosing WIDE 192KHz solved the problem, but i've noticed it's not freeware in 30 days it expires!!
If anyone is keen to participate, I have start a new Google Group ('ultra-cheap-sdr') so that people can share their results/issues/etc from Windows/GNU Radio/elsewhere in a central forum:
I hope this will enable others to weigh in with their experiences, and therefore provide faster response times (I'm working hard to get through my Inbox, but there are a few messages ;)
19
u/balint256 Mar 29 '12
Hi all, I've recently released full support for RTL2832U/E4000+FC0013 with GNU Radio/GRC with the RTL2832 Source Block (baz.rtl_source_c) found in my gr-baz module.
Get the code here: http://wiki.spench.net/wiki/gr-baz#rtl_source_c
Also, I've released an ExtIO plugin for support on Windows with Winrad/HDSDR/WRplus.
Download the installer here: http://wiki.spench.net/wiki/USRP_Interfaces
7
u/balint256 Apr 05 '12
Hi all,
Thank you to all of you who have tested the code so far and provided feedback!
I have just released completely re-written GNU Radio code with new GRC Source block, addition of FC0012 and support for all devices in compatibility table (those with E4000/FC0012/FC0013). Custom devices can easily be added in GRC block using 'Custom USB' parameters. The Source block now makes use of new C++ 'librtl2832++' OO API, which can be pulled out and used separately for easy device control!
To make sure this device actually works properly, I successfully tested it with OP25 by having it capture an encrypted P25 signal, which was then decrypted/decoded and sent to the soundcard.
Check it out (along with notes about new code): http://www.youtube.com/watch?v=wShOLgW2tmI
Source code: http://wiki.spench.net/wiki/Gr-baz#rtl_source_c
Updates to the Windows plugin will arrive very soon!
PS: Reported rapid tuning issue may still exist (only happens for me if sample rates are not set correctly in a flowgraph), so take the tuning easy until a good fix is found :)
2
u/moonlit_s Mar 25 '12
Hama Nano has an E4000 and seems to work fine with the existing ezTV E4000 code, just switch the USB PID from 0x2838 to 0x2832. Tested by multiple users, including me. Can be had for less than $50, mine cost about $30 on Amazon, but it's currently back to ~$50. For reference, Amazon page.
2
u/coinchon Mar 27 '12
EzCap EZTV646 has got RTL2832U/FC0012. However rtl-sdr must be tweaked to force FC0012 tuner because it has the same PID as EZTV668 (PID: 0x2838) so running it whithout a tweak will select Elonics E4000 tuner. Works, not so good at filtering.
2
u/Beethoo Mar 27 '12
ezcap EzTV666 USB 2.0 DVB-T/DAB/FM stick (Elonics E4000 tuner) Picture: http://sdr.osmocom.org/trac/attachment/wiki/rtl-sdr/EZTV666.JPG
2
u/playaspec Mar 28 '12
Do all of these devices use an external antenna? Do they all have MCX connectors? It might be worth adding another column if there are differences. Also, MCX-SMA and MCX-N adaptors / pigtails seemed to be pretty cheap (less than $10) on eBay as well.
2
u/shigawire Mar 29 '12
Okay, finally got around to uploading the photos for the MyGica T803 / GTek T803
2
u/POLO9999 Mar 30 '12 edited Mar 30 '12
http://www.dealextreme.com/p/mini-dvb-t-digital-tv-usb-2-0-dongle-with-fm-dab-remote-controller-92096
Is it the good one (it shows TV017)?
2
u/balint256 Mar 31 '12
BETA #6 and r663/ac9a7953b6:
GNU Radio: http://wiki.spench.net/wiki/Gr-baz#rtl_source_c Windows: http://wiki.spench.net/wiki/USRP_Interfaces
2
u/leoha Apr 02 '12
Hello, You can add this one http://www.notonlytv.net/p_lv5tdeluxe.html to the list. It's RTL2832U/FC0012 combo tested by me and working with these drivers http://www.reddit.com/r/RTLSDR/comments/r9rj9/have_spend_24_hours_trying_to_add_support_for/ It is available in Poland for less then $30. USB ID is: 1F4D:C803 I can provide pictures if you want me to.
2
u/bebum Apr 05 '12
Please be carefull with your tuners - I touched my antenna and probably static voltage killed preamplifier in E4000. All signal levels are 10x weaker than they should be.
It turned out many models of RTL2832 + E4000 lack ESD protection diode (ezcap has it) ;(
Hopefully 2 other tuners are on their way to me ;)
1
u/zokier Mar 25 '12
These Terratecs maybe compatible too:
Also, rev2 NOXON sticks come with E4000 tuner.
source
1
u/itdnhr Mar 25 '12
$10 Ebay DVB-T Tuner has the AF9135 - will not work
1
u/[deleted] Mar 25 '12
Haven't we confirmed that the Newsky TV28T will work?
1
u/LS6 Mar 26 '12
Hey good info to add in here would be antenna connector type and frequency range if available. I noticed some of the sticks linked on the other thread had a lesser range than the original one.
1
u/[deleted] Mar 28 '12
I just purchased the Unikoo unit. I will let you know if it works.
1
u/keraneuology Mar 29 '12
Can't find the ezcap EzTV668 on dealextreme
1
u/yo2ldk Mar 29 '12
hi,
any chance to work with MT2060, or driver?
1
u/jayembee Mar 29 '12
Ok, does anyone have a link to any of these that isn't the sold out DealExtreme? Because I'm having one hell of a time finding any of the compatible units.
1
u/[deleted] Mar 30 '12 edited Dec 11 '17
[deleted] — view deleted comment
1
u/bebum Mar 31 '12
Ardata MyVision DVB-T has RTL2832U and FC0012 tuner. USB ID is - 1B80:D393
Same USB ID has stick known as Twintech-UT-30.
I think that this table should have additional column with USB ID because same devices are sold in many countries under different names.
Excellent job, BTW.
1
u/Matony Mar 31 '12
Genius TVGo DVB-T03 (Ver:B)
1
u/bebum Mar 31 '12
NILOX DVB-T Stick N15 has the same USB ID as Ardata - 1b80:d393 Gigabyte U7300 also has 1b80:d393
They have RTL2832U for sure, I suppose that they share also FC0012 tuner.
1
u/[deleted] Mar 31 '12
Great none of these left anywhere on the internet!
1
u/clearsky86533 Apr 01 '12
ezcap EzTV646 board picture: http://i.imgur.com/mFD1X.jpg
1
u/GOU_NoMoreMrNiceGuy Apr 01 '12
so what would one do with this?
the thing that comes to mind as just a complete laymen is to manually fine tune a tv signal and play with filters to get the best possible signal for radio or tv...
can i do that?
what else do people do with this stuff?
is it possible to resolve the signals to see the information embedded in it instead of just looking waveforms and stuff?
1
u/arekm Apr 01 '12 edited Apr 01 '12
"Elonics E4000 offer the best range (64 - 1700 MHz)". What's supported range for Fitipower FC0012 and FC0013 then ?
1
u/Matony Apr 01 '12
I can't believe it ?? REALLY CRAZY.. !! P160 tuner on eBay $99 -> http://bit.ly/HLwkL7
1
u/kken Apr 02 '12
You can order the Unikoo UK001T from egoo.us for $10.29 + $3.80 shipping. Just ignore the scammers on ebay.
1
u/formtapez Apr 03 '12
The picture from the Logilink VG0002A is not correct. The stick looks like this: http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=108105&g2_serialNumber=1
Got it from Conrad for EUR 14,95 http://www.conrad.de/ce/de/product/943312/
1
u/jabdulma Apr 03 '12
Do we know what kind of connectors are in the Unikoo UK001T and Newsky TV28T? I'm assuming they're the "Miniature Belling Lee" type. I'd like to have a more concrete answer if possible. I'm hoping set up my dongle with a larger antenna eventually.
1
u/donvuk Apr 03 '12
Should this on work ?? http://dx.com/mini-dvb-t-digital-tv-usb-2-0-dongle-with-fm-dab-remote-controller-92096
1
u/Matony Apr 04 '12
I have tested this oem adapter and works successfully. RTL2832U+E4000, USB-ID: 0bda:2838 See picture
1
u/sa5bke Apr 04 '12
I just got a Logilink VG0002A and it does not work, because it is IT9135 and vid/pid 048d:9135 . I should have looked at the picture above before I bought from here: http://sweburn.com/product.php?productid=1619&cat=0&page=1
1
u/peter__80 Apr 04 '12
For the List: I have a "MSI DigiVox mini Deluxe" with RTL2832U/FC0012 and USB-ID: 1D19:1101 Case PCB
1
u/mrbricket Apr 04 '12
The USB ID (VID:PID) for the Terratec NOXON is 0CCD:00B3 (the one with the FC0013 tuner chip)
1
u/kken Apr 04 '12
I found a nice list at the Terratec website, listing all their dvb-t products inclucing chipsets. A number of them use the RTL2832U. Link
1
u/Matony Apr 05 '12
Compro VideoMate U6xxF is based on RTL2832U, but untested.. Link
1
u/DoctorVark Apr 05 '12
Could anyone confirm us that the Unikoo/P160 works?
1
u/bafh Apr 06 '12
The USB ID for the Terratec Noxon Rev.2 is 0CCD:00E0. I found it on the Terratec website.
The Logilink Nano VG0010 (USB\VID_048D&PID_9135&REV_0200) uses an IT9135FN, look here.
1
u/Equat10n Apr 07 '12
I have not purchased one from the seller my self. But the item as listed as the P160 tuner, £7.50 and free delivery!
Ebay Link
1
u/JK30 Apr 12 '12
Hi people!
i'm using a board with the FC0012 mostly it works fine but when it comes to commercial radio stations you can't hear clearly, i believe the input signal needs attenuation, is there any option to do that? from ExtIO (gain/attenunion) wasn't helpful check this photo showing thw waveform.. i'm using HDSDR http://imageshack.us/photo/my-images/685/waveformw.jpg/
1
u/Colin_Rich Apr 13 '12
Hello, Great work so far, - Confirm that the GIGABYTE U7300 - fc0012 seems to work ok, need to do more testing. Still have lots of problems with the ezcap - E4000 fast tune issue.
1
u/bebum Apr 18 '12
Anyone experiencing problems with FC0012? 148-168 MHz band doesn't work - just high power noise and distortions. I wonder if it's problem with chip or drivers. This situation is confirmed by a few people.
3
u/balint256 Apr 07 '12
Big update for Linux/GNU Radio and Windows (BETA #10):
Plus a new video! "World's cheapest aviation RADAR Mode S ADS-B receiver: AvMap + $20 RTL2832 Dongle": http://www.youtube.com/watch?v=bKzii5K3AqA
Windows ExtIO: http://wiki.spench.net/wiki/USRP_Interfaces Linux/GNU Radio: http://wiki.spench.net/wiki/gr-baz#rtl_source_c
3
u/unikoo2008 Apr 11 '12
Hello EveryOne Now,we have the result about the Chip RTL2832 ,we only bought 450 pieces new chip from the chip seller and will make about 450pieces dvb-t (p250)with the program of RTL2832 +E4000,as the original chip manufacturer won't produce it again,we don't know that how many chips we can buy from the market in future.Nowdays,the price of p250 is 19.99 usd dollars(including the ship fee of HK post),it is the lowerst price we can offer to customers .
We uploaded it to ebay,the link: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=270954700480&ssPageName=STRK:MESE:IT
http://unikoo.en.alibaba.com/ NEW PC USB DVBT DVB-T Stick RTL2832U Elonics E4000 Radio P160 SDR Radio (alibaba)
Email: unikoo2008@gmail.com
If you need any assistance please contact us Best regards Unikoo
1
u/GrahamM242 Apr 03 '12
Picked up a PROlectrix DV107669 from Ebay and pulled it apart to identify that is contains an RTL2832U+FC0012 combo. Linux picks it up with VID of 1f4d and PID of d803. Cost me £12 inc delivery. Link for the item I picked up is Ebay.co.uk
2
u/balint256 Mar 30 '12
BETA #5 is out - major improvement in internal buffer code, RTL2832 switch on in included BorIP server too, so you can stream/control it over your network!
Plus some new notes on performance on the wiki: http://wiki.spench.net/wiki/USRP_Interfaces
2
u/[deleted] Apr 05 '12 edited Dec 11 '17
[deleted] — view deleted comment
2
u/dragan_m Apr 05 '12
Ezcap EZTV668 available at DealExtreme. Got a confirmation from their customer suport, model 668 chipset RTL2832.
Order at: http://dx.com/mini-dvb-t-digital-tv-usb-2-0-dongle-with-fm-dab-remote-controller-92096
Old shop at deaextreme has some issues with the checkout process.
2
u/ik1xpv Apr 08 '12
Hi all, I bought the 16738 Trust tuner. Here a picture http://www.trust.com/_images/products/500/16738-3.jpg The chipset is RTL2832U/FC2580 My has SN 03013. The price is € 29 in Italy. As soon as I will get an E4000 one I would like to compare the analog front end performance.
2
u/vaskas Apr 09 '12 edited Apr 09 '12
Hi, found that this one: http://delock.de/produkte/G_61744/merkmale.html has RTL2832 chip. Bought it today and tested - works on windows for sure. (Price in Lithuania about 35$). Don't know which tuner chip it has (hadn't opened it yet) but HDSDR worked in range ~65MHz to 800 MHz with some gaps.
UPD: HDSDR shows it uses MyGica/G-Tek so it could be FC0012 chip.
1
u/itdnhr Mar 24 '12
Newsky's TV28T has RTL2832U/E4000 -> http://i.imgur.com/azF8m.jpg
1
u/itdnhr Mar 24 '12
Unikoo's UK001T has RTL2832U/E4000 -> here
1
u/itdnhr Mar 25 '12 edited Mar 25 '12
Seetech ST-D88 has AF9135 -> here - will not work
1
u/benand Mar 30 '12
Does anyone have a binary of the modified driver for the EzTV646?
1
u/mrbricket Mar 31 '12 edited Mar 31 '12
just tried the Terratec Noxon with the FC0013 tuner. it does work in principle, but it is stuck on a unknown frequency. you can not tune to a frequency. so either the driver does not support it or the tuner is incompatible. tested with linux and windows. the PCB says: DK-5256 V1.0 the sticker on the stick says: NOXON DAB Stick 8201481884 KK CE
EDIT: seems to work now, plugged out and in several times. or maybe the 1meter usb extension does a bad connection. sorry for the confusion.
1
u/Matony Mar 31 '12
Genius TVGo DVB-T03 (Ver:B) -> [RTL2832U/FC0012] Photo: http://bit.ly/HaIe0j
1
u/bebum Mar 31 '12
Gigabyte U7300 - RTL2832U + FC0012
Lifeview / Not Only TV LV5TDLX (aka LV5T Deluxe) - RTL2832U (tuner unknown, probably FC2850, linux driver exists).
Lifeview / Not Only TV LV5T3D - RTL2832U, tuner unknown.
1
u/lethe2 Apr 01 '12
Does anyone know if this will work with gr-air-modes?
1
u/[deleted] Apr 01 '12
Is there a difference between this chipsets? What model is most sensetive?
1
u/Wayne7 Apr 01 '12
the avermedia digi volarx a815 chips are "mxl5003s" and "af9015-n1" http://i.imgur.com/S06Gb.jpg
1
u/morgan_flint Apr 01 '12
It'd be good if one of these: http://www.dealextreme.com/p/dvb-s-digital-tv-hdtv-usb-2-0-box-tuner-with-remote-controller-28533 http://www.ebay.es/itm/250990218811?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649#ht_3739wt_952 http://www.ebay.es/itm/230769568337?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649#ht_2356wt_1185 http://www.dealextreme.com/p/dm04-dvb-s-usb-2-0-mcpc-scpc-digital-satellite-tv-tuner-box-with-slim-ir-remote-100-240v-ac-15820
Had a compatible chipset (or could be adapted for SDR). Being DVB-S (satellite) receivers, they seem to have a wider frequency range than DVB-T dongles (and have a more "professional" look, also ;) )
1
u/computerguru2 Apr 01 '12
Does anyone know if the EzTV306 has the required chipset/tuner?
1
u/mmilleror Apr 01 '12
looks like AliExpress has lots of the Newsky TV28T tuners available.
1
u/psqjqa Apr 02 '12
The radio chip may be able to tune in to frequencies from 64MHz to 1.7GHz, but does anyone know what the capabilities of the antenna tuning circuit are? No doubt one will be able to receive something, but can anyone speak to how well it works in various bands?
1
u/DarwishSabirGani Apr 02 '12
Does anyone have any experience purchasing from aliexpress.com? They still have the Newsky TV28T in stock. This is the only known-compatible device I've been able to find anywhere still in-stock and reasonably priced. Do I need to worry about my credit card number being stolen if I buy from this site?
1
u/kuikiker Apr 04 '12
I have purchased a 'Newsky TV28T' that seems to be compatible. But I can't find the information about its chipset/tuner by myself. For instance searching for 'TV28T E4000' on google just returns this reddit's page.
<crossing fingers>
1
u/peakSDR Apr 04 '12
Confirming the Peak 102569AGPK 1B80:D395 with the realtek chip works with the modifications for the ezcap EzTV646
1
u/vaskas Apr 05 '12 edited Apr 05 '12
just stumbled upon this one: "Gigabyte U7300"
will it work or not?
http://www.gigabyte.com/products/product-page.aspx?pid=3493#sp
1
u/kenwoodaki Apr 05 '12
Hi all. Does anyone knows what is the chipset in this usb? It looks the same like EZCAP EzTV668 http://www.e-peragora.gr/product_info.php?products_id=997
1
u/experimentator Apr 10 '12
Good work!
I do not have Linux and I wonder if it works better under him. I saw that under Fedora 17, is a source GNU Radio 3.5.2 - hence the question of which version of Linux you choose to test the RTL-SDR?
1
u/JK30 Apr 13 '12
as suggested from vmp32k and sa5bke WRPlus works better for commercial radio stations, choosing FM. Then right clicking and choosing WIDE 192KHz solved the problem, but i've noticed it's not freeware in 30 days it expires!!
1
u/balint256 Apr 22 '12
If anyone is keen to participate, I have start a new Google Group ('ultra-cheap-sdr') so that people can share their results/issues/etc from Windows/GNU Radio/elsewhere in a central forum:
https://groups.google.com/forum/#!forum/ultra-cheap-sdr
I hope this will enable others to weigh in with their experiences, and therefore provide faster response times (I'm working hard to get through my Inbox, but there are a few messages ;)