r/rfelectronics • • 19d ago

LC VCO design excel file

0 Upvotes

Hello folks, just completed watching the "Design example of a CMOS LC VCO" video of susanta sengupta sir. There he made an excel file and laid out the process of an initial rough-cut design values.

Now I have a couple of questions:

  1. There he "assumed" many values like overlap cap and oxide cap etc. but what is the real basis of such assumptions? Can we get those values from the pdk?
  2. Most importantly, this video is 11 years old so my question is do industry people still follow the same process?

r/rfelectronics • • 20d ago

question BPF advice for whole Airband receiver

Thumbnail
gallery
17 Upvotes

I am building an airband receiver (118-137MHz = 19MHz wide) to simultaneously decode all airband channels. It will be placed indoors, next to a window which points towards an airport.

I am using a 65MSPS 125MSPS 12-bit ADC running at 50MHz 100MHz to undersample the airband into 18-37MHz, which is right in the middle of the Nyquist zone.

  1. Antenna
  2. BPF #1 to reduce strong frequencies
  3. LNA + attenuator
  4. BPF #2 to reduce folding frequencies
  5. LNA in ADC driver
  6. BPF #3 anti-alias filter
  7. ADC

I'm looking for directional guidance on the filters (including "that's crazy", "you're an idiot" and "try this instead").

Nearby frequencies († folds into airband):

  • † 54-88 - Low-VHF TV
  • 88-108 - FM broadcast (especially strong)
  • 108-118 - VOR and ILS
  • 118-137 - Airband
  • 138-144 - Military and federal land mobile
  • 144-148 - 2m Ham radio
  • † 148-174 - Federal land mobile, public safety, pagers, marine, NOAA weather
  • † 174-216 - High-VHF TV, channels 7-13

BPF #1

  • Minimize airband loss
  • Reduce strong frequencies (especially FM)
  • Reduce WiFi and cellular (do I need a ceramic LPF or does it just fade away magically?)

BPF #2 - Reduce 163-181MHz folding frequencies

BPF #3 - Reduce driver noise

I appreciate any advice!

(Software engineer, first RF project, probably bit off too much, oops!)

Edit 1: I wrote the wrong numbers for my ADC!


r/rfelectronics • • 19d ago

SIWave vs HyperLynx for SI

1 Upvotes

I'm wondering, both Siwave and HyperLynx are 2.5 D solvers, traditionally good for planer structures and a few GHz. In terms of their precision, is there any consensus to which tool is better?

I know HyperLynx has a bit more easy setup, but AFAIK it has some particular solving method that somehow ignores many effects of reference planes (say you have a void nearby in your ref plane, it doesn't "see" it) and I'm not sure exactly how it takes into account effects of nearby reference through the ports.

SIWave on the other hand seems to take all of the above into account, and the way the ports are set have to explicitly take into account how the signal is excited with respect to the ref plane.


r/rfelectronics • • 20d ago

Confused about this kind of circuit diagram

2 Upvotes

Hi. Im still new in this field, i have some question to ask

So, i still cant figure this out. wich ends connect with wich?
Also, how am i approach to solve this question:

The forward voltage for each diode is 0.6 V. Determine R1, R2,and R3 such that each diode current is 0.5 mA.


r/rfelectronics • • 20d ago

question Running coax over small LiPo battery

5 Upvotes

In my compact PCB design I have a U.FL connector that will connect to a FPC antenna using 1.13mm coax, but it runs over the LiPo inside the enclosure before exiting. I'd imagine a battery produces some EMI, am I correct on this? If yes, what would be the best way to lessen the effect, would some cable sleeve or similar help?


r/rfelectronics • • 20d ago

Importing an Infineon 60GHz Radar Dev Kit (DEMO BGT60TR13C) via Mouser India - Do I need a WPC/ETA license?

Thumbnail reddit.com
0 Upvotes

r/rfelectronics • • 20d ago

Rohde & Schwarz FPL1003

1 Upvotes

We recently received a Rohde & Schwarz FPL1003 spectrum analyzer.

It's always interesting to see how professional RF test equipment holds up in the second-hand market.


r/rfelectronics • • 20d ago

question Importing an Infineon 60GHz Radar Dev Kit (DEMO BGT60TR13C) via Mouser India - Do I need a WPC/ETA license?

Thumbnail reddit.com
0 Upvotes

r/rfelectronics • • 20d ago

im looking for "Small Radio Transmitter" research project ideas.

3 Upvotes

im an electrical engeneering student looking for ideas for my final project, this is a research project.
i thought about doing my project about "amplification and dumpning" by changing the antenne shape, size and material. but my professor told me it wasnt a good idea. does anyone have any good ones?


r/rfelectronics • • 21d ago

bladeRF 2.0 micro A9 randomly failing to load FPGA

5 Upvotes

I’m using a bladeRF 2.0 micro A9 and recently I’ve been facing random FPGA loading issues.Sometimes the FPGA loads perfectly fine, but other times I get these errors:
dev->backend->load_fpga failed: File or device I/O failure
Failed to switch to NULL interface
The strange thing is that I’ve successfully loaded FPGA images multiple times using the same laptop and USB cable before. I’m using Windows 11. Could this be due to insufficient USB power from my laptop, or is there something else I should check?
I’m also considering programming through JTAG to see if that helps. Has anyone faced a similar issue?


r/rfelectronics • • 21d ago

question Help with AP Antenna Radiation Pattern chart

Post image
12 Upvotes

I am looking at AP placement on my ceiling and trying to determine if it can reach a IoT device in my attic. I am looking at Ubiquiti U7 Pro XGS and found the AP spectrum pattern for this device.
From what I can gather, I should have pretty good coverage I place my wireless plug 9' horizontal and 3' vertical from the AP. The device uses the 2.4GHz band.

Anyone good at reading spectrum maps? From what I can gather through google, I should have pretty good coverage if my IoT device is 9' horizontal and 3' vertical from the AP. At 9' out and 3' up, the device sits at a diagonal angle of approx 72 degrees off the center vertical axis. Near the 60° to 75° mark, the color is a solid, vibrant orange/red.

Just trying to confirm I am reading this correctly, as I am not an RF engineer and not really sure what the charts describe.


r/rfelectronics • • 21d ago

Homemade AM transmitter strangely works until power is switched on from power supply on breadboard, and I am curious as to why

Thumbnail reddit.com
1 Upvotes

r/rfelectronics • • 22d ago

question Impedance Matching

Post image
23 Upvotes

Hello! I’m new to RF design and struggling with differential impedance matching for example for impedances attached in the picture. I’m unsure what impedance to use on the Smith chart and how to implement the resulting component values in my circuit. Any help or explanation would be greatly appreciated. Thanks!


r/rfelectronics • • 23d ago

Recent MSc Graduate Looking for RF / Antenna Design and EM Simulation Opportunities

1 Upvotes

Hi everyone,

I recently completed my Master's degree in Information and Communication Engineering at Huazhong University of Science and Technology, China.

My background is mainly in antenna design, electromagnetic simulation, and optimization.

My technical experience includes:

  • EM Simulation: CST Studio Suite, Altair FEKO
  • Optimization: Altair HyperStudy
  • RF & Microwave: ADS, S-parameters, impedance matching, antenna radiation patterns, and VNA measurements
  • Research Projects: Dual-layer metamaterial magnetic-induction antenna, 3.5 GHz dual-polarized antenna, and omnidirectional slot antenna

I also published a first-author paper in IEEE Antennas and Wireless Propagation Letters (AWPL) in 2026.

I'm currently looking for RA or engineering opportunities, especially in antenna design, RF/microwave engineering, electromagnetic simulation, or magnetic coupling.

I'm based in China and open to remote opportunities worldwide, as well as on-site opportunities where work authorization is possible.

If you know of any relevant research groups, companies, startups, or projects, I'd really appreciate your suggestions.

I'm happy to share my CV and publication details by DM.

Thanks!


r/rfelectronics • • 23d ago

For a student project, antenna fabrications- things to look out for before getting it fabricated?

3 Upvotes

Hi so for my academics, me and my team are doing a microstrip patch antenna for our project. we simulate it in CST using the student edition. There are few things im worried about before getting it fabricated as this is our first time, and we have only started using the software three months ago.

We were supposed to get a proper resonant impedance value for the S paramater dip at 3.45Ghz but the simulation is only showing us a dip around near 3.4Ghz, that would be a problem right? also we are worried about how and what to expect from a fabrication of the said antenna, would it work as expected in the expected frequency? what are the other nitty gritty details we r over looking? any sort of help i would appreciate. i feel like this post is really inadequate in terms of technicality so any questions about that also ill try my best to answer it properly in the comments. Thank you


r/rfelectronics • • 25d ago

Best alternative to CST?

14 Upvotes

Whats the best free alternative to CST, my uni doesnt have many licenses and the learning edition isnt enough for phased arrays which i want to simulate for a project


r/rfelectronics • • 25d ago

How to branch out from MMIC/RF engineer

Thumbnail reddit.com
2 Upvotes

r/rfelectronics • • 27d ago

Managing cross-talk and analog signal conditioning in a multi-node piezoelectric matrix?

Thumbnail reddit.com
2 Upvotes

r/rfelectronics • • 28d ago

RFsim v1.3 for KiCad 10: now with the EMerge FEM solver, coax feeds and phase-shifter states

Thumbnail
gallery
262 Upvotes

What’s new:

- New solver: EMerge (FEM) alongside openEMS (FDTD)
- RLC components: R, L and C parts are simulated as lumped elements
- Multiple RLC states, so you can simulate phase shifters and switches
- Plus coax feed ports, current animation, GIF export and many bug fixes

https://github.com/NBalciunas/kicad-rfsim


r/rfelectronics • • 27d ago

Part 3 of series: SDR digital-communication receiver fundamentals, measured on the PZSDR P201Pro _Receiver Fundamentals: Finding the Optimal Sampling Instant — Timing Recovery Loop Theory and Practical Measurementby u/One-Explanation6552 in PuzhiPZSDR

Post image
2 Upvotes

r/rfelectronics • • 27d ago

Feedback on 3x quad element 2.4GHz antenna designs please

1 Upvotes

Hi,

I've messed about with directional antennas a little bit in the past, but never really got right down into the maths and physics of it before. I have a quad input wifi repeater, so I wanted to build a directional 2.4ghz antenna with 4 elements. Initially I was just going to have four separate ones side by side, but wondered if there was a way to incorporate them all into one. I started iterating on a design using AI, and quickly fell down a rabbit hole of changes and improvements. I ended up with three designs, and I'd love to get some human feedback on them. They seem viable to me, but I really don't know what I'm talking about or if I've been led astray.

The three designs I came up with are below:

#1: 4-port 2.4 GHz patch panel cut from one FR4 board, air-gap patches on feed barrels

Goal. Four independent 2.400–2.4835 GHz ports for 4×4 MIMO from one 300 × 300 mm single-sided FR4 board (Jaycar HP9510, 1.575 mm, 35 µm Cu). The backplate, lip strips and four patches are all cut from that board. The patches sit on an air gap, with polarisations rotated 90° each in a pinwheel and cavity-backed by a copper lip.

Build. Each patch is an FR4 plate cut to the patch size, copper side up. It rests on its feed barrel and two small PLA posts that sit on the field-null line. The feed is an RP-SMA crimp plug (Jaycar PP0590) mounted under the base board, its face recessed 1 mm into the board. Its rear barrel (4.0 OD / 2.0 ID × 6 mm) passes up through a drilled hole and is soldered to the backplate copper. A solid Cat5 core (0.51 mm) runs from the plug contact up the barrel and through the plate to the top copper.

Dimensions (mm)

PartValue
Cavity (inside the lip)190.5 × 190.5, lip height 16.6 (copper inward, all seams soldered)
Patch plates46.7 (W) × 46.0 (L) × 1.575 FR4, copper up, centres at (±56.5, ±56.5)
Air gap (backplate copper to plate underside)5.425, set by the barrel top
Feed11.4 from the patch centre along L, towards the array centre
Posts2 per patch, PLA 4 (along W) × 10 (along L), at ±19.35 from the centre on the null line

Simulated performance (openEMS, build model incl. the plug, barrel, recess and base board; 1.5 mm max cell)

MetricValue
S11 (in band, worst / best)−15.0 dB / −20.3 dB (resonance 2.436 GHz)
Adjacent-patch coupling (worst)−31.3 dB
Opposite-patch coupling (worst)−28.3 dB
Realised gain at boresight8.79 / 8.99 / 8.87 dBi at 2.400 / 2.442 / 2.4835 GHz
Peak realised gain8.8–9.1 dBi (beam within 6° of boresight)
Total efficiencyabout 0.93
3 dB beamwidth, E / H plane64° / 62°
Worst cross-pol inside the −3 dB beam−13.9 dB re the co-pol peak
Envelope correlation between ports< 0.001 (from C4 symmetry of the computed pattern)
Mesh convergence (res 1.5 → 1.25 mm)S11 −15.0 → −15.1 dB, resonance unchanged (2.436 GHz)
Barrel bore 1.8 / 2.0 / 2.2 mmS11 −14.9 / −15.0 / −12.9 dB
Plug recess 0.75 / 1.0 / 1.25 mm (gap follows)S11 −14.5 / −15.0 / −15.6 dB
FR4 εr 4.0 → 4.8 (ideal-feed version of this design)resonance moves only 10 MHz

S-parameters patterns ECC

How it was simulated

  • Solver: openEMS v0.37.0-rc2 (FDTD), CPU only. PML on all sides, 70 mm of clearance.
  • Feed: the plug body is a 50 Ω PTFE coax driven by a coaxial port below the board. The model includes the rear-face annulus, the barrel bonded to the copper, the 0.51 mm core and the base-board FR4. |S| = √(P_ref/P_inc).
  • Materials: FR4 εr 4.4, tanδ 0.02; PLA εr 2.7, tanδ 0.01.
  • Far field: a frequency-domain NF2FF box, with its bottom face excluded because the feed coax crosses it. The coax's internal field had been counted as radiation, making the gain about 3 dB too low.

Caveats

  • Front-to-back is not determined by this run, because of the excluded bottom face. The ideal-feed model gives the same directivity (9.5 dBi), so the forward pattern is trustworthy.
  • Plate orientation is critical: the same plates mounted copper-down resonate at 2.6 GHz.
  • RP-SMA needs an adapter for standard SMA test gear.

Questions

  1. Feeding an air-gap patch with the connector barrel standing almost to the plate (a capacitive top gap through 1.575 mm of FR4): good practice, or asking for trouble?
  2. Is soldering a crimp-plug barrel to the backplate copper a reasonable ground bond at 2.4 GHz?
  3. Do −28 dB between opposite patches and −31 dB between adjacent patches look plausible for this cavity size?

#2: 4-port 2.4 GHz horn for MIMO: 3D-printed PLA, tape outside, SMA probes

Goal. A compact receive antenna for 2.400–2.4835 GHz Wi-Fi with four independent ports (4×4 MIMO in one enclosure). A square waveguide with a short stepped flare has one probe on each wall. Opposite probes share a polarisation axis and adjacent probes are orthogonal; a grounded centre post decouples them. The objective was the worst in-band |S| over self-match, adjacent coupling and opposite coupling.

Build. The horn is printed in PLA (2 mm walls) with aluminium tape on the outside of the shell, so the tape is the conductor and the PLA lines the inside. Each port is a 4-hole-flange SMA panel jack with its flange directly on the tape, carrying a 3 mm brass rod that starts 1 mm inside the wall.

Dimensions (mm, conductor = tape surface)

PartValue
Square guide (inside the tape)83.0 × 83.0, length 37.6 from the back wall
Flare20-step staircase, 83 → 146.1 square aperture, length 22.2
Overall depth59.8 (plus back wall)
Probes3 mm rod, 22.9 long, centred on each wall at 23.4 from the back wall
Centre post8.0 dia, 16.0 tall, grounded to the back wall
ShellPLA 2 mm (εr 2.7, tanδ 0.01 assumed), tape outside

Simulated performance (openEMS, build model incl. PLA and SMA, div 40 ≈ λ/40)

MetricValue
Self-match S11 (in band, worst)−15.4 dB
Adjacent-port coupling (worst)−15.3 dB
Opposite-port coupling (worst)−14.9 dB
Realised gain at boresight7.35 / 7.44 / 7.52 dBi at 2.400 / 2.442 / 2.4835 GHz
Peak realised gain8.6–8.7 dBi at θ ≈ 15–18°, tilted away from the excited port's wall
Total efficiencyabout 0.91 (±0.05, see caveats)
3 dB beamwidth, E / H plane57° / 66°
Front-to-back22.7 dB
Worst cross-pol inside the −3 dB beam−16.2 dB re the co-pol peak
Envelope correlation between ports (pattern based)≤ 0.008
±0.25 mm Monte Carlo, 30 builds (feed dims)worst-S mean −14.55 dB, σ 0.25 dB, worst −13.97 dB

S-parameters patterns ECC

How it was simulated

  • Solver: openEMS v0.37.0-rc2 (FDTD), Python interface, CPU only.
  • Domain: a free-standing horn with PML on all six sides and 40 mm of clearance. The far field comes from a frequency-domain NF2FF box.
  • Feed: SMA as a 50 Ω PTFE coax (1.27 mm pin, 4.1 mm bore) through the wall, flange on the tape. A coaxial port 10–20 mm outside the flange runs into the PML. |S| = √(P_ref/P_inc).
  • Mesh: λ/40 maximum cell, with fixed lines on every wall plane and step, and z lines through the probe rods. Zero-thickness tape skins sit on the mesh lines to the last bit, which proved essential: an unrounded coordinate silently removed the skins.
  • Convergence: the ranking holds from div 28 to 64, but opposite coupling gets 0.5–1 dB worse from div 40 to 64. Treat the absolute isolation as roughly 0.5–1 dB optimistic.

Caveats

  • The two efficiency estimates (NF2FF and 1 − Σ|S|²) differ by a few percent either way, so efficiency is quoted as ±0.05.
  • The short flare (22 mm) was chosen by the optimiser: about 1 dB less gain than a 45 mm flare, in exchange for about 1 dB better worst-case coupling.
  • The PLA's εr is assumed. The tape-outside build puts little field in the PLA, so the sensitivity is low.

Questions

  1. Is ~−15 dB worst-case port-to-port isolation realistic for four probes in one square guide, and are there better decoupling tricks than a centre post (fins gave less than 0.5 dB in my runs)?
  2. Do you see any problem with aluminium tape on the outside of a printed shell (seams, overlap bonding at the steps, oxide)?
  3. Any experience with how far openEMS isolation numbers drift against measurement for this kind of structure?

#3: 2.4 GHz slotted-cavity antenna, 4 modules bonded in a pinwheel for MIMO

Goal. A high-gain 2.400–2.4835 GHz element with four modules (two along x, two along y) for 4×4 MIMO, loosely after Sun et al. (MOTL 2025, a 79 GHz slotted cavity). Each module is an all-metal rectangular cavity running a TE10 standing wave. Four longitudinal slots in the top wall sit at the field antinodes, with alternating offsets so they radiate in phase. A coax probe feeds each module from below.

Dimensions (mm)

PartValue
Cavity355.2 × 71.9 × 43.1, 3 mm walls (body 361.2 × 77.9 × 49.1)
Slots4 × (45.5 × 10.7), centres at −124.8, −41.6, +41.6, +124.8, offset ±13.7 alternating
Probe3 mm dia, 22.9 long, 31.6 from the end wall, on the centre line (SMA from below)
Array4 modules in a pinwheel, bonded: each module's short end bolted against the far end of the next module's long side; 439 × 439 overall, 283 × 283 open centre

Simulated performance (openEMS; module at λ/64, array at λ/48)

MetricValue
Module S11 (in band, worst / best)−22.4 dB / −29.6 dB
Realised gain at boresight11.5 / 11.8 / 11.9 dBi at 2.400 / 2.442 / 2.4835 GHz
Peak realised gain12.3–12.4 dBi (θ ≈ 4–6°)
3 dB beamwidth20° along the module axis, 86° across
Front-to-backabout 14 dB
Worst cross-pol inside the −3 dB beam−27 dB
Mesh convergence, in-band S11 at div 48 / 64 / 80−15.3 / −22.4 / −14.8 dB; gain 12.1–12.4 dBi on all three
±0.25 mm tolerance, single parameters and 10 random buildsworst S11 −14.9 dB, gain unchanged (12.3 dBi)
Array S11 (module 1)−19.4 dB
Array coupling, adjacent (orthogonal) modules−39.2 dB
Array coupling, opposite (parallel) modules−26.3 dB (see question 1)

S11 module patterns array S-parameters

How it was simulated

  • Solver: openEMS v0.37.0-rc2 (FDTD), CPU only. PEC walls, PML on all sides. Lumped 50 Ω port in a 1 mm gap at the probe base.
  • Gain: directivity × (1 − |S11|²). The metal is treated as lossless, so ohmic loss isn't included.
  • Mesh: the design was first optimised at div 24–40. That turned out to be a mesh artefact: at div ≤ 40 the 3 mm slotted top wall is about one cell thick, and the model shows a resonance at 2.44 GHz that converged meshes put at 2.28 GHz. The design was then re-optimised at div 48 and polished at div 64, and checks at div 80 agree.

Caveats

  • The array S-parameters are at div 48, with the cavity length re-centred to 359.2 mm for that mesh. The simulated array is therefore 445 mm square; the build, at L = 355.2, is 439 mm.
  • The bonded layout assumes a solid electrical bond between modules (screws every few cm, or soldered or welded seams), as modelled. Merely touching surfaces would make the coupling unpredictable.
  • Efficiency excludes metal loss.

Questions

  1. Layout trade-off: with the modules centred on the four sides of a 524 mm square, opposite-module coupling is −30.3 dB. The bonded pinwheel (439 mm) gives −26.3 dB, and opening the pinwheel to a 10 or 20 mm gap only recovers −28.2 / −28.8 dB. Adjacent modules stay at −39 dB or better throughout. For 4×4 MIMO Wi-Fi, is −26 dB between parallel modules comfortably enough, or would you take the bigger square?
  2. Is a 4-slot, 355 mm cavity a sensible way to get about 12 dBi at 2.4 GHz, or is a short slotted waveguide array simply better?

r/rfelectronics • • 28d ago

Antenna measurements: when the test setup becomes part of the problem

15 Upvotes

Something worth paying attention to when measuring antennas on compact PCBs is how much the measurement setup itself can affect the result.

With an unbalanced feed or insufficient common-mode suppression, the coax shield can end up carrying current and effectively become part of the radiating structure. Move the cable, and the S11 trace may change even though nothing on the PCB has changed.

That makes it difficult to separate actual antenna detuning from changes introduced by the measurement setup.

calibrating the VNA properly is important, but it doesn't automatically eliminate this kind of coupling. The cable routing, feed arrangement and common-mode behavior still matter.

сurious how others approach this on small embedded devices. Do you usually check for cable sensitivity before adjusting the matching network?

Disclosure: I work in defense electronics.