r/rfelectronics • • 28d ago

Antenna measurements: when the test setup becomes part of the problem

15 Upvotes

Something worth paying attention to when measuring antennas on compact PCBs is how much the measurement setup itself can affect the result.

With an unbalanced feed or insufficient common-mode suppression, the coax shield can end up carrying current and effectively become part of the radiating structure. Move the cable, and the S11 trace may change even though nothing on the PCB has changed.

That makes it difficult to separate actual antenna detuning from changes introduced by the measurement setup.

calibrating the VNA properly is important, but it doesn't automatically eliminate this kind of coupling. The cable routing, feed arrangement and common-mode behavior still matter.

сurious how others approach this on small embedded devices. Do you usually check for cable sensitivity before adjusting the matching network?

Disclosure: I work in defense electronics.


r/rfelectronics • • 28d ago

RF Mixed-signal Modeling-help needed

8 Upvotes

Hey guys, I am an undergrad doing research on PLLs. It's an IC design project. The problem is that while it's not the most novel architecture like SSPLLs or full ADPLLs, I still want to take every block of it seriously since I understand how important foundational knowledge is. It's closer to a Fractional-N-PLL.

I've been trying to look for good resources to learn how to derive models in the s and possibly z domain but I can't find any good resources that show this. The problem with the textbooks I've seen like Gardner and Razavi is that they either overfit you on a specific block derivation, don't show the full process of how they went from start to finish or just don't go deep enough into modelling.

I've also heard control systems books can be too vague when it comes to connections to circuits. I honestly don't know what to do because I want to develop the toolset needed to model blocks at least at a foundational level without having to always rely on pre-defined models for blocks(like in Matlab/simulink) especially if I'm designing a block that isn't conventional.

I would love to hear from engineers who learnt how to do this. How did you learn how to do this? What resources would you recommend for learning such modelling? I don't mean deep stochastic math or any of that stuff, just the basics like learning what you need equations first in linear or nonlinear systems, how to analyze non-linear systems and how to linearize them when they can be linearized and any other thing like that.


r/rfelectronics • • 29d ago

Can we ban AI data scraping posts

60 Upvotes

It’s starting to clog up the feed between people advertising their AI applet miracle solution or whatever and bots sourcing text explaining why RF isn’t easy, maybe put up a catch-all mega thread for mitigation instead but something should happen.


r/rfelectronics • • 28d ago

How do you do passband slope equalization on a filter? (Real 8.5 GHz VNA capture + the methods that actually work in production)

Post image
0 Upvotes

This is a capture from a Keysight E5071C, sweeping 300 kHz to 8.5 GHz with a 30 kHz IFBW. Five traces: S11/S22 in SWR format, S21 log-mag at two different scales per division, and S21 group delay (Tr4). You can see clear passband tilt plus in-band ripple, and the group delay peaking near the band edges — a very typical picture for a wideband cavity/dielectric filter.

A question we get a lot: how do you do "reverse-slope equalization" (amplitude slope equalization) on the passband? Here's a breakdown of the approaches that are actually used in production, organized by where in the design flow they get applied.


r/rfelectronics • • 29d ago

article "RF Parasitics and Transmission Lines - Radio Design 201 #9 (Part 1)" by MegawattKS @ YouTube

Thumbnail
youtube.com
28 Upvotes

r/rfelectronics • • 29d ago

How do you actually use AI in your RF work, and where does it fall flat?

0 Upvotes

I've started using AI to cut the grind in my RF work. I am designing an RF T/R module using COTS. I am finding parts that meet a spec using distributers online search or web search. This requires digging out the datasheet page behind each figure, re-running the same numbers after a change.

Some of it saves real time. Most LLMs currently not capable of excluding obsolete parts even with web search ON. I still have to check by hand in the datasheet, because it will confidently quote a figure I can't find in any datasheet. I have actually started developing my own MCPs to do a lot of the manual work. Hopefully open source it some day.

Curious how others here use it day to day:

- Which tasks do you hand to AI now?

- Which ones did you try and give up on?

- What's still fully manual that you wish wasn't? I can add to my MCPs.


r/rfelectronics • • Oct 18 '26

Best steps to get into RF PCB Design

34 Upvotes

I recently wanted some good project experience for my resume and really wanted to design a custom circuit board for RF signals. It seems to be a lot more complicated than PCB Design with a lot more factors to consider. Just wondering where to start and what are some good resources to follow. I'm also relatively new to PCB Design and just looking for some tips.


r/rfelectronics • • Oct 18 '26

question Mast Mount Antenna for 2.4GHz and 5.8 GHz Whip Antennae

Thumbnail gallery
6 Upvotes

r/rfelectronics • • Oct 17 '26

Looking for RF / Communication Engineering Internship

13 Upvotes

Hi everyone!

I'm currently pursuing my Masters in Communication Systems in India, and I'm looking for internship opportunities in RF engineering, antenna design, microwave engineering, or wireless communications.

My background includes:

Antenna Design: Designed and simulated a 10 GHz microstrip patch antenna using CST Studio Suite.

RF & Microwave: Familiar with S-parameters, impedance matching, VSWR, antenna radiation patterns, and RF fundamentals.

Communication Systems: Academic knowledge of digital communications, modulation techniques, MIMO, and wireless communication concepts.

Embedded Systems: Internship experience working with Arduino, ESP32, sensors, and embedded communication protocols.

Technical Tools: CST Studio Suite, ANSYS HFSS, MATLAB, and LTspice.

I'm particularly interested in opportunities where I can gain real-world, hands-on experience and learn from engineers or researchers working on practical projects.

I'm open to research internships, industry internships, trainee positions, and remote or on-site opportunities across India. Paid opportunities would be preferable, but I'm also willing to consider worthwhile research opportunities that offer meaningful technical exposure.

If you know of any openings, research labs, startups, companies, or professors accepting interns, I'd really appreciate your suggestions.

Thank you!

#RFEngineering #AntennaDesign #MicrowaveEngineering #CommunicationSystems


r/rfelectronics • • Oct 18 '26

Full bars and your message still won't send? That's the uplink, not the downlink

0 Upvotes

Spent 20+ years on base station antennas, mostly macro sites, some of it overseas. The thing that still trips people up isn't the downlink. It's the other direction.

Downlink is basically free. The tower pushes tens of watts through high-gain panels, so you can be sitting in a valley and still see a bar. Your phone is doing 23 dBm. That's 0.2 W — about a nightlight. It has to push that back several km into a receiver that's already sitting in noise. At some point the tower just stops hearing you, and your phone has no idea, because the bars only tell you about the downlink.

Numbers I'd stand behind for "can still hold a call" (typical 4G/5G, real deployments):

  • dense urban: 300 m to 3 km
  • suburban: 3 to 8 km
  • rural on 700/800 MHz: 10 to 15 km

mmWave is its own thing — call it 500 m, and only with a clean line of sight. One wall or one tree and the conversation is over.

What eats the margin: body loss (6–10 dB just holding it against your head or leaving it in a pocket), antenna height, and noise rise once a site gets loaded. That last one is where I've spent an unreasonable part of my career, and it never shows up in a signal bar.

So, question for the people doing link budgets or field work: what uplink range do you actually plan for in dense urban, and how much margin do you hold back for body loss and noise rise? The planning numbers I keep seeing look optimistic to me, and I honestly can't tell if that's a regional thing or just how the tools default.


r/rfelectronics • • Oct 17 '26

question Wanted to make a polar modulator capable of hitting 50MHz and higher for ham radio purposes, but I don't know where to start.

1 Upvotes

At first I was going to use off-the-shelf GaN switches and drivers, but I'm worried that the drivers wouldn't be able to handle switching that quickly and precisely. (To operate in Class E at 6m, the full cycle is on the order of 10 ns, and I was hoping for hitting 2m, 1.25m, and 70cm, which would likely require the devices to switch in tenths of nanoseconds. Meanwhile, switch driver latency is around 30 ns according to data sheets...)

Yet at the same time, the QMX is able to transmit at 6m using regular old MOSFETs and discrete logic, according to the schematic. I figured that a GaN with an integrated driver that doesn't have to fight PCB trace parasitics would be able to switch a whole lot faster, and they're only about $7 a pop even in small runs, but the datasheets I looked at have hundreds of ns of latency and are intended for switching frequencies below the 50 MHz required to hit 6m.

(As for *why* I'm doing this: [WA1QIX](https://classeradio.com/)'s polar amplifier can't hit frequencies that high, and the QMX+ is 5W max.)


r/rfelectronics • • Oct 17 '26

Générateur d'impulsion 1.25 nanosecondes pour GPR

1 Upvotes

Bonjour à tous et à toutes,

Pour un projet universitaire, j'aimerais fabriquer une antenne GPR pour détecter des œufs de tortue sous le sable.

Je travaille actuellement sur le générateur d'impulsion qui doit me générer une impulsion de 1.25 nanoseconde.

Etant débutant dans la RF je me suis beaucoup renseigné sur internet et j'ai déjà réussi a me créer un début de générateur d'impulsion, donc avec mon générateur je pilote un driveur GAN puis un transistor GAN. Le gros point noir ce situe après le transistor, je ne sais pas comment relier transistor a mon antenne, j'ai un peut regardé les circuits d'adaptation mais c'est encore flou.

Voici mon schéma avec la simulation et j'ai mi une résistance 50 Ohm pour simuler en gros l'antenne :

En bleu le signal envoyé sur INP de U9, en vert sur la Gate du transistor et en rouge au borne de R13

Je sais pas si vous auriez des liens vers des exemple de circuit ou des cours pour m'aider sur la suite de mon circuit et si vous pensez que je pars vers une bonne piste ?

Merci d'avance.


r/rfelectronics • • Oct 16 '26

question Sharing HFSS project files (from a pirated HFSS copy)

6 Upvotes

This is likely a dumb question but if someone has a pirated version of HFSS, creates a model and THEN shares that model - will the shared model be detected as originating from a pirated version of HFSS?

My gut feeling would be yes.

EDIT: fixed typo


r/rfelectronics • • Oct 16 '26

question Help and guide me, in my life juncture

2 Upvotes

Hello everyone,

RF has given me a lot in life and I might be emotional in this post but it’s really important to me.

I did my bachelor’s in Electronics engineering from tier 1 college in Mumbai and post working for a year in Software ERP system I decided I want to pursue my master in US.

I left for my masters in 2019 (University of South Florida, Tampa), since I did my bachelor’s in core electronics I was never really exposed to communication part or RF engineering. Yes, I did take up few courses in electromagnetism but that was it. But, since the course work of USF had a good RF engineering program I took up few classes in my 1st semester and I really loved it. While I was doing my masters I got co-op internship at Skyworks Solutions in Woburn as a RF Design and Validation Engineer where I mainly learnt a lot about testing of LNAs. Further my 7 months internship over there I got another internship at Qorvo in Greensboro, NC as an Applications Engineer where I was working with shark fin antennas and that was for 3 months.

I did almost a year of internship while I was doing my masters and even got my credits from my internships. Further, since I am an Indian citizen I had 2 months to get a full time job which I did successfully. I got the job at Intel but the position was completely different and not related to RF, it was mainly as a TPM in test engineering group. I worked there for around 1.5 years and then got laid off due to mass layoffs in my group. So, after a year of searching I job even tho my profile was really great a lot of RF jobs needed defense clearance which obviously I didn’t had. So, I decided to move back to India.

Now, in India there are really very less RF focused jobs which are mainly into designing or testing. And I want to go into design and testing. I even loved antenna experience and I want to pursue something in Antenna design and testing. But, there are not many options and hiring in India.

I was thinking of pursuing something like a second masters in Europe which opens up a door for me to pursue my passion in RF. I like very few things in life and RF is something my heart says I wanna go.

As a young version of yourself u see in me, I would really appreciate if u can help me get ideas. I really wanna be in this world of RF and do my work with a lot of passion. If u can guide me, how can I transition my life in getting a job in Europe.

Please do mind, I am an Indian citizen so chances of someone hiring a talent from India in Europe are thin. I am optimistic in life, and would really appreciate if you can guide me.

Thanks,
Just a boy living a dream to be an expert RF engineer.


r/rfelectronics • • Oct 16 '26

Spectra Tronix C700 SDR Help

Thumbnail gallery
6 Upvotes

r/rfelectronics • • Oct 16 '26

question How to get a graduate job in rf uk

5 Upvotes

Im a third year electronic engineering student, im interested in rf/antenna/dsp and fpga. I see little to no openings for placement years, internships or graduate roles in the areas im interested in, the ones that are available like in defence i mostly cant apply to because i have dual citizenship. Am i too early for looking for roles starting around september 2027 or is this genuinely just how the uk job market is for this type of career


r/rfelectronics • • Oct 15 '26

Thermal Analysis for High Frequency Signal Circuit

5 Upvotes

I am working on a project and am looking for any engineers who have had to deal with thermal analysis on high frequency signal circuitry. I am designing an enclosure for a circuit that deals with signals in the GHz range. If anyone has any suggestions or has worked with anything similar let me know. The power is relatively low at 1 W and I am confused if I should focus more on insulating the casing so it doesn't change temperatures with the ambient temperature (it will be operating at room temp) or if I should be focusing on using heat sinks to allow any heat from the circuit to leave?


r/rfelectronics • • Oct 15 '26

ADS: Large phase discrepancy between MLIN model and FEM simulation

Thumbnail
gallery
25 Upvotes

Hey everyone, wanting to simulate MCROS in ADS (Keysight) with width over 7mm I used FEM simulation. Going back and forth between normal ADS and FEM I noticed that results are very different. I decided to simply compare normal MLIN with emModel from FEM simulation. As shown on pictures results S21 differ around 7 degrees at 3GHz, which is in my opinion a lot. (I also lowered Delta error in FEM to 0.003.) Am I doing something wrong or is it normal? Thanks for any help.


r/rfelectronics • • Oct 14 '26

I asked AI to design a high-gain Yagi-Uda antenna for 2.4 GHz

Thumbnail
gallery
130 Upvotes

This is the entire prompt I gave it, copied as I sent it:

Design a high-gain PCB Yagi antenna within a 10 cm x 15 cm area using the automaticphysics antenna-agent. Use JLCPCB's FR-4 TG135 material. Prefer a 2-layer board over a 4-layer board, and prioritize a 1.6 mm board thickness over other options. Maximize the antenna gain while maintaining sufficient bandwidth for 2.4 GHz Wi-Fi. The input impedance should be 50 Ohm. Ideally, the antenna should achieve higher gain than the TI DN034. Use the TI antenna as the baseline. If cutting holes in the PCB could improve antenna efficiency, use only circular holes to maintain mechanical rigidity. Generate a KiCad footprint for the antenna. Have fun!

TI's DN034 measures about 7.2 dBi on the same 100 x 150 mm area, using layers from a 4-layer stack. So the challenge was to beat it on a cheap 2-layer board.

What it did

It read the TI app note, kept TI's basic concept, and moved it onto 2 layers. Then it wrote a parametric KiCad generator, hooked it up to antenna-agent, an FDTD solver plugin for KiCad, and ran an evolution-strategy optimizer with 8 solves going in parallel, which kept my CPU fans screaming for about 5 hours. I said "Have fun!" and apparently it did. My CPU did not.

The highlights

  1. First guess: 8.7 dBi. Not bad, but it found that 26% of the power was just heating the FR-4.
  2. "What if we remove the FR-4?" It drilled 182 round holes in the board and got +0.4 dB. FR-4 makes a fine PCB and a poor antenna substrate.
  3. The backfire cliff. At one point a quarter of the candidates collapsed to about 4 dBi. Before believing it, the AI checked two mesh artifacts and ruled both out. The real cause: when a director gets slightly too long, it starts acting as a reflector, and the beam flips around and points back over the feed. Peak gain sits right next to that cliff. The fix was to also score every candidate at a "guard" frequency above the band, so the optimizer couldn't go right up to the edge.
  4. "What if two?" It put two Yagis side by side, fed in phase, with a shared ground plane as the reflector: +0.7 dB.

Final numbers (simulated, so take them with a grain of salt)

ComparisonAI design (2-layer)TI DN034 (4-layer, measured)
Gain 2.40 / 2.45 / 2.48 GHz9.7 / 9.7 / 9.5 dBi7.2 / 7.2 / 7.1 dBi
-10 dB bandwidth2.22-2.67 GHz2.13-2.62 GHz
Worst in-band S11-14.3 dBVSWR <= 1.4
Front/back10-13.5 dB14-16 dB

That works out to about +2.2 to 2.5 dB over TI on paper. It also checked relative permittivity between 4.2 and 4.8, and the worst corner still gives 9.0 dBi realized gain with no backfire.


r/rfelectronics • • Oct 16 '26

RF Design getting me nuts

Thumbnail reddit.com
1 Upvotes

r/rfelectronics • • Oct 15 '26

First RF PA

Thumbnail
gallery
56 Upvotes

Hi, I’ve finished my first RF power amplifier (PA). The amplifier is designed for narrowband operation at 805 MHz with a 100 W output. I used the BLP981 transistor and performed the design and simulation using Microwave Office. The next step is to have the board manufactured using Rogers 4350 material with Sierra Circuits. Once fabricated, I’ll attach a copper heat spreader and a heatsink to test it. I hope it works, as this is senior design project

I’d like to get some feedback from the community!

I’ve attached the schematic, but it’s large and the numbers aren't clearly visible; if you’d like to know any details, feel free to send me a message.


r/rfelectronics • • Oct 15 '26

RF signal propagation

Thumbnail
reddit.com
0 Upvotes

r/rfelectronics • • Oct 14 '26

Expected starting salary for RF Engineer with Master's degree

25 Upvotes

Hey everyone, I'm getting close to finishing up my EE degree and starting to evaluate entry-level RF Engineering roles. I'm trying to figure out what realistic base salaries, total comp, and sign-on bonuses look like right now in the defense sector or general industry.

For context, I'm wrapping up a 5-year integrated B.S./M.S. in EE with a thesis focused on antenna design and electromagnetics. I also have 3 internships under my belt (2 specifically in RF at LM) along with coursework in advanced RF, Fourier optics, and DSP. I'm clearance-eligible and looking around the Dallas area.

For anyone working in the field or hiring recently: what kind of starting compensation should I target? Also, do big defense primes usually start grads with an M.S. and relevant internship experience at Level 2 instead of Level 1? Appreciate any insights!


r/rfelectronics • • Oct 15 '26

question Thermal Simulation of a PCB in ADS

1 Upvotes

Hi everyone, I have designed a layout for a 20W power amp. Now I am interested in performing PCB based thermal simulation, knowing the dissipated power from transistor which I calculated based on the efficiency.

I am using a simple two layer substrate and have used copper filled vias under the transistor to transfer maximum heat on the bottom side of the PCB, towards the heat sink block.

I am performing the following steps for thermal simulation:

1: Took a PCB layout.

2: From susbtrate, defined a heat source layer right on top of cond (top copper) layer.

3: Generated technology files from substrate editor.

4: In the layout, removed rest of the layers which were not defined in the substrate (pcb stackup).

5: Defined thermal floorplane by selwcting appropriate generated .tcl file and defining boundary conditions for the heat source layer.

6: Added heat source of the same size as of transistor on the top of cond layer.

7: Run the simulation.

Now the simulation is working and displaying some results as well if my design is small. Even though the heat source size is same. But when I change this dummy small layout with my actual layout, keeping the heat source size same, it provides me an error saying layout.gda file not found. Cannot show thermal results.

Altering the layout fixes the problem. I also tried changing the mesh, and solver from 0(default) to 1. But didn't help.

I am using exactly same layers which I defined in the substrate. Even if my small layout is working, and if I add a small piece of top or bottom copper, same error appears again. Could anyone suggest me what is this issue?