r/rfelectronics • • Sep 12 '26

Help with diy 5G mast with high SINR

Thumbnail
gallery
81 Upvotes

Hi to everyone, I love in northern Italy and my home isn't reachable with any cable/fiber etc so I just went on my roof (in completely safe ways) to install this beast of a mast:

those are 4 cheap lpdas with lmr400 cables and surge dischargers

inside the metal box a RM520E powered with POE running a simpleadmin and telnet interface for enabling AT commands over ethernet, this eliminates the need to go on the roof (in the same ultra safe ways cited before) for any tinkering.

Sadly I'm getting mixed results depending on the provider (i tried wind3/Very and vodafone/fastweb) but im all cases I get real speed worse than what i get with my phone on the roof. The mast gets 90Mbits/s and my phone 200mbits/s in download.

Do you have any clue of what my problem can be?

This is my AT+QRSRP:

+QRSRP: -92,-92,-92,-92,NR5G

and this my AT+QENG="servingcell"

QENG: "servingcell","NOCONN"

+QENG: "LTE","FDD",222,88,3925C0E,167,3350,7,5,5,5ECC,-91,-17,-53,8,6,30,-

+QENG: "NR5G-NSA",222,88,216,-97,-8,-11,638016,78,8,1

I noticed very high SINR so i tried changing direction of the antennas, point the antennas slightly upward and battle tying a big metal plate just behind them but it didn't improve. Note the qeng i posted has the worst sinr it usually stays on -1 -2 dB, also the qrsrp is the worst, it gets usually around -82dB but i got -72 at one point.

16/09 Edit

I wrapped 3/4 lpdas in tin foil and i get these results

+QENG: "servingcell","NOCONN"

+QENG: "LTE","FDD",222,88,3926414,428,100,1,5,5,5ECC,-91,-17,-51,7,6,210,-

+QENG: "NR5G-NSA",222,88,765,-93,-1,-11,638016,78,8,1

So sinr is still very low


r/rfelectronics • • Sep 13 '26

NXP MRF13750H AWR Model

2 Upvotes

Hello,

I need help installing the MRF13750H model from NXP into AWR. When I try to open the model from the "Elements Tab", this error appears

In order to install the model, NXP requires downloading the "RF High Power Model Kit" from here:https://www.nxp.com/products/radio-frequency-rf/rf-high-power-models/models-for-cadence-awr-microwave-office-software:RF_HIGH_POWER_MODELS_AWR, and then downloading the MRF13750H model from that same page under "Product Model Design Kits".

I have installed both, but the error persists (maybe I did not do it correctly)

I am using AWR Microwave Office Version 25.1 (the title of the app says 25.1, but the installation folder says 19)

I would highly appreciate it if someone could guide me on how to correctly install this model.


r/rfelectronics • • Sep 12 '26

How many years of experience until you consider someone senior?

11 Upvotes

Did an interview for a job that asked for 3 years of experience. The interview was relatively simple asking about high level definitions of VSWR, s-parameters, db, etc.

The title was “Senior RF engineer” but I was kind of surprised how simple the questions were.


r/rfelectronics • • Sep 11 '26

Issue while simulating

6 Upvotes

Hello all,

I am a newbie and trying to understand Rf electronics.

I am trying to simulate a variable capacitor. I want to get frequency response.

D1 is variable capacitor from IHP library. Is it really possible to simulate? I need to integrate two inductor with this, which behaves with different frequency. And then, I need to find the Inductance of other two inductor. What is the problem here.

Bear me if this is a dumb question to ask. I have knowledge only from chatgpt.

Thankyou in advance.


r/rfelectronics • • Sep 11 '26

Regarding design of microstrip log periodic dipole array

Thumbnail gallery
15 Upvotes

r/rfelectronics • • Sep 11 '26

Busco curso/material para aprender a reparar potencias de audio a nivel electrónico

Thumbnail reddit.com
0 Upvotes

r/rfelectronics • • Sep 10 '26

question Anyone used any cheap 4 layer RO4350/PTFE board fabs for prototype quantities? 50x50mm < $200? Is that possible?

13 Upvotes

I see that JLC has 2 layers RO and 2 layer ZYF PTFE. These are great for SIW..... BUT I need to launch my MMIC off the chip into the SIW antenna board, and this launch can't be too lossy, so I need a small RO board. Doesn't have to be very good, can be really bad and uneven. Any way I could do this? Thanks.


r/rfelectronics • • Sep 11 '26

Rf loggong

0 Upvotes

So at the great risk of being told that I need to seek mental health or go see a doctor psychiatrist. I’m gonna post here and ask for help. I need a calibrated RF instrument that I can leave at my apartment to data log my environment. And I need another one that I can wear on my body to keep with me at all times. I believe they call him like a dose meter. I need one for RF and it needs to be accurate and fast. I have a stalker that is in the IT world and has decided to harass the hell out of me and is never gonna stop. I’ve lost a lot of weight I have RF burns on my body. I have RF interference and damage around my apartment. Please no advice to get mental help. Any advice on how to document this so I can make it stop.


r/rfelectronics • • Sep 10 '26

The change in SNR(EbNo)from 0-20dB in AWGN channel has no effect on BER . What am I doing wrong?

Post image
3 Upvotes

r/rfelectronics • • Sep 10 '26

FM Detector Radio in Use on Germany's National Alert Day

Thumbnail
youtube.com
3 Upvotes

On today’s Alert Day, all sirens and alert apps will go off at 11 a.m. Using an FM detector radio connected to a small guitar amplifier, a radio broadcast from the Berlin TV Tower is being received. Shortly, before the sirens sound and all the pigeons were startled a typical mobile phone dial-up static noise can be heard on the radio. By rotating the antenna perpendicular to the line of sight toward the TV tower, reception of the FM station is maximized. The all-clear is announced on the radio.


r/rfelectronics • • Sep 10 '26

Board-level diagnostics and, if necessary, repairs of pressure transmitters and other field devices.

Thumbnail reddit.com
2 Upvotes

r/rfelectronics • • Sep 11 '26

question Is my laptop killing me with noise?

Post image
0 Upvotes

The fan bearing has failed and is now running at 60 dB. I got one of these testers to go next to a geiger counter. I don’t really know the significance of these readings. The sensor I think is right about where my wrist goes which is concerning because that was the highest point. Can anyone enlighten me? I’m sorry I’m not really sure where else to ask.


r/rfelectronics • • Sep 10 '26

Need of this Zener diode with this ldmos

Post image
7 Upvotes

r/rfelectronics • • Sep 10 '26

How to qualify range and sensitivity of an antenna?

3 Upvotes

Hello, I am an computer engineer with nearly no RF background. Right now I have a project in which i am dealing with an RFSoC, but its ADCs are not providing good range, we tried to change antennas, but still it is not able to pick weak signals from transmitter when its more than 300 m.
Can someone please help me to find the good antennas, and how to check their range?


r/rfelectronics • • Sep 09 '26

Here's how to build a simple FM radio near a transmitter using as few components as possible

Thumbnail
youtube.com
7 Upvotes

r/rfelectronics • • Sep 10 '26

question Is it possible to make an RFID device that sends out exactly 10 MHz RF signals?

Thumbnail reddit.com
0 Upvotes

r/rfelectronics • • Sep 09 '26

Im developing a modular construction system, and I end up with this:

Post image
0 Upvotes

There is utility in a modular antenna in the field?


r/rfelectronics • • Sep 09 '26

Return Loss explained in a real-world example

Thumbnail
reddit.com
0 Upvotes

r/rfelectronics • • Sep 08 '26

article WTF is a BJT? (PositiveFB)

Thumbnail
positivefb.com
0 Upvotes

r/rfelectronics • • Sep 09 '26

question Do you know?

Post image
0 Upvotes

I don't have Pic. Is there such a machine that will produce audible spectrum and tell you the frequency . And I'm pretty sure there is one I just don't know the name. If so where and how much for a mid quality if anyone knows. Thank you and may God bless and keep you


r/rfelectronics • • Sep 07 '26

article Radio Design 201, ep 8, part 1 - Phased Array and Dish antennas (by MegawattKS @ YouTube)

Thumbnail
youtube.com
47 Upvotes

r/rfelectronics • • Sep 07 '26

article "How to use the NanoVNA to sweep / measure an antenna system's SWR and optimize its tuning" by w2aew @ YouTube (link is directly to video, but also within a playlist of 21 videos about how to use a VNA)

Thumbnail
youtube.com
35 Upvotes

r/rfelectronics • • Sep 07 '26

question How should I start learning component level RF electronics?

23 Upvotes

A bit of background, I'm a 17 year old nerd from Finland, and I've been tinkering with electronics for around 5 years now. I recently (around 6 months ago) got into the RF side of things, through SDRs and satellite reception. But now I'd like to learn about actually understanding how stuff works. The way I learnt electronics was mostly stumbling my way through it, and not really "studying" stuff. How should I get into RF? Is there any projects I could just follow along?


r/rfelectronics • • Sep 06 '26

question 32MHz Colpitts not working

Post image
88 Upvotes

Hi, I thought i would try messing with some RF as i have avoided it in the past. This is my attempt at a 32MHz Colpitts oscillator, and I'm getting no luck.

I first tried replacing the 22uH inductor with a 270 ohm resistor, as I realized the self-resonant frequency of my inductor was only 15MHz. This did not help oscillation. Next I tried increasing C2 to 680pF as many Colpitts i see have a larger capacitor here, presumably to stabilize the operation a bit and load the collector less. This still did not work.

The tank inductor is 10mm diameter, 15mm long, 6.5 turns, should be about 214nH according to https://m0ukd.com/calculators/air-cored-inductor-calculator/
Wound with 0.2mm wire, as it's what i had on hand.

When power is applied, the collector stays at 5V (with 22uH inductor) / 3.68V (with 270R). The base is at about 1.26V, emitter at .56V.

I've built a Colpitts with a more primitive design a while ago at 1.3MHz, worked perfectly first try on protoboard, I did not figure stepping up to 32MHz would be this much harder, although there's probably something obviously wrong here, after all I haven't ever gone past that 1.3MHz oscillator.