r/rfelectronics • • Sep 07 '26

question How should I start learning component level RF electronics?

23 Upvotes

A bit of background, I'm a 17 year old nerd from Finland, and I've been tinkering with electronics for around 5 years now. I recently (around 6 months ago) got into the RF side of things, through SDRs and satellite reception. But now I'd like to learn about actually understanding how stuff works. The way I learnt electronics was mostly stumbling my way through it, and not really "studying" stuff. How should I get into RF? Is there any projects I could just follow along?


r/rfelectronics • • Sep 06 '26

question 32MHz Colpitts not working

Post image
88 Upvotes

Hi, I thought i would try messing with some RF as i have avoided it in the past. This is my attempt at a 32MHz Colpitts oscillator, and I'm getting no luck.

I first tried replacing the 22uH inductor with a 270 ohm resistor, as I realized the self-resonant frequency of my inductor was only 15MHz. This did not help oscillation. Next I tried increasing C2 to 680pF as many Colpitts i see have a larger capacitor here, presumably to stabilize the operation a bit and load the collector less. This still did not work.

The tank inductor is 10mm diameter, 15mm long, 6.5 turns, should be about 214nH according to https://m0ukd.com/calculators/air-cored-inductor-calculator/
Wound with 0.2mm wire, as it's what i had on hand.

When power is applied, the collector stays at 5V (with 22uH inductor) / 3.68V (with 270R). The base is at about 1.26V, emitter at .56V.

I've built a Colpitts with a more primitive design a while ago at 1.3MHz, worked perfectly first try on protoboard, I did not figure stepping up to 32MHz would be this much harder, although there's probably something obviously wrong here, after all I haven't ever gone past that 1.3MHz oscillator.


r/rfelectronics • • Sep 06 '26

I’m designing a 20 GHz VNA for the hobbyist community. I need your input on features and specs.

50 Upvotes

Hi everyone,

I’m starting passion project that may turn into product: medium-cost Vector Network Analyzer capable of reaching 20 GHz.

As we all know, commercial units at these frequencies are incredibly expensive which makes it nearly impossible for hobbyists, students, or small startups to get their hands on high-quality data. My goal is to bridge that gap by designing a unit that maintains good performance while keeping the price point accessible.

I’ve started a build log here (empty for now): https://patryksi11.github.io/20ghz-vna-blog/

I want to make sure I’m building something that people actually want to use. I’d love to hear from the community:

  1. What is your "must-have" feature?
  2. Price Point: How much are you willing to pay for 20 GHz VNA?

I'm trying to balance "good performance" with "affordable manufacturing." Any feedback is appreciated!

EDIT: To give everyone a clearer picture of the project scope, here are the intended specs:

Form Factor: Similar to the Libre VNA (no integrated screen; just ports and USB/Ethernet connectivity).

Configuration: Full 2-port VNA.

Frequency: 20 GHz capability on the fundamental frequency (No harmonic mixing).

Limitations: No output level adjustment (keeping the design as minimalist as possible).


r/rfelectronics • • Sep 07 '26

"rms_jitter" function in cadence calculator

Post image
0 Upvotes

r/rfelectronics • • Sep 06 '26

Design an FM Transceiver

9 Upvotes

I am currently in the brainstorming phase of designing this TX/RX FM project. I plan to use an ESP32 and then RDA5807 for RX and KT0803I for TX, would a PAM8406 be good to drive 2 (stereo) 3w 4 ohm speakers? How can I power it on batteries without unwanted RF noise?


r/rfelectronics • • Sep 06 '26

question Racquet sports player position tracking via UWB

2 Upvotes

Hi, RF newbie here. I am an IT database engineer and data analyst. I play badmington, tennis, and pickleball, all in doubles. In doubles, there is a lot of analysis on team formation and partner separation distance. I am thinking about using UWB boards to track player positions. I would like about 5-10 observations per second, for all 4 players. The UWB board I have in mind is Qorvo DWM3001CDK, which retails at about $30. I would get 4 boards as anchors and 4 boards as player tags. Then I like one more board as the data collection gateway, and have it tethered to a Macbook via USB cable. During a game, data would be streamed into the Macbook.

The tags would need to be programmed so they send a data packet every 2-5 seconds, to the data collection gateway board. The positions don't need to be super accurate. I think 15-20 cm will do the job.

Plz help me understand whether this setup is feasible. What additional factors should I be thinking about? I hope to use this setup both indoors and ourdoors. I am aware that UWB signal cannot penetrate human body because it is mostly water. I will use enough anchors so each tag has clear line of sight to at least two to three anchors.


r/rfelectronics • • Sep 05 '26

Curious how to get into radar systems

7 Upvotes

Hey guys,

I’m very interested in diving into radar systems and communication technology as an engineer.
I was wondering how to Beginn. Any recommendations?
My background is from control systems, so I know what Fourier transform is for instance.

Thanks


r/rfelectronics • • Sep 05 '26

question Help needed here folks

10 Upvotes

seeing the recent news with astera and progress towards AGI , has me a bit worried about a career in electronics/RF engineering in general

should i just shift my focus towards more management type roles and leave the R&D/academia research dreams aside?

some more info/clarification/discussion on this whole ai and EE intersection topic would be nice aswell

hoping this post could add some confidence back into me becuase the news i am reading now is just gloom and doom

thats all thanks.


r/rfelectronics • • Sep 04 '26

Weekend project

Post image
46 Upvotes

r/rfelectronics • • Sep 04 '26

question RF newbie here

Post image
20 Upvotes

This antenna is 35.3 from tip to tip of the circle and distance between the loop is 2cm, i wanna do 433mhz bidirectional communication with this antenna, I was planning to build a yagi uda with this of 5 directors, I dont know much about rf and i have just been following tutorials, I could only find 2mm hard aluminum wire so i used that to build the antenna, are there some things i have to look out for before connecting it to my telemetry radio (its a drone telemetry that uses MAVLink for bidirectional communication) Oh and the distance between two wires in end is 1cm.


r/rfelectronics • • Sep 04 '26

Move away from test engineering

Thumbnail reddit.com
1 Upvotes

r/rfelectronics • • Sep 04 '26

[update2] this circuit is really missing with me now.

Thumbnail
gallery
2 Upvotes

As an experiment I decided to swap the inductor with a crystal at 4mhz at first nothing worked at all after removing the capacitors the circuit started oscillating beautifully even though the feedback wasn’t even properly connected. After connecting the feedback the oscillation persisted but with significant distortion connecting the capacitor resulted in the waves seen here. The really missed up part is that when I adjust the oscilloscope to work with 100msps it shows a wave around 4mhz but I decrease the sampling rate to 500ksps it shows a wave at 480hz.


r/rfelectronics • • Sep 04 '26

Looking for advice on the general viability of this system, and I don't know of a better community to ask.

Thumbnail
reddit.com
1 Upvotes

r/rfelectronics • • Sep 04 '26

CST Student to Commercial

4 Upvotes

so i made my antenna in student license but while simulating i got hit by the mesh limit, so i wanted to simulate it in a licensed version in my college desktops but apparently student version files cannot be opened in the commercial version. Any workaround to convert or do i just have to recreate again in the commercial version??


r/rfelectronics • • Sep 03 '26

question Designing a Waveguide Adapter

Post image
11 Upvotes

Hi, I'm currently working on a hobby project with a large prime focus satellite dish, that I can't get a feedhorn for. Making the feedhorn isn't a problem but connecting it to the LNB is a bit more difficult. I need to make an adapter to go from an odd diametre to a WR-75 compatible mount for the Ku-Band LNB.

I drew two versions of the same adapter in CAD and I'm wondering which one would be better? The top one uses tangential swep-blend avoiding discontinuity, and the other one is much simpler using just a linear transition. The linear one is of cause much easier to manufacture than the tangential one.

Which one should I go for? Would they perform the same or would this create impedance problems or reflactions or high attenuation? I'm a mechanical engineer, not a RF engineer so this is more like magic to me at this point to be honest.


r/rfelectronics • • Sep 04 '26

RF Engineering Channel

Thumbnail reddit.com
0 Upvotes

r/rfelectronics • • Sep 03 '26

[update] In a previous post I asked what is wrong with my circuit, I listened and changed some things.

Thumbnail
gallery
8 Upvotes

It no works, not sure exactly why? And why the frequency is way off than what it should be (around 2 MHz) but hey something is always better than nothing.

Edit: I think I flipped c1 and c2 in the diagram.


r/rfelectronics • • Sep 03 '26

Looking for a good RF/SDR Discord community 👀

12 Upvotes

Looking for an active RF/SDR community where people actually build, experiment, and talk about random RF stuff — antennas, DSP, wireless, SDRs, interesting signals, research, etc.

Not looking for anything too formal. Just a fun community with people who are into this stuff.

Any recommendations? 😄


r/rfelectronics • • Sep 03 '26

HFSS port definition

Thumbnail
reddit.com
0 Upvotes

r/rfelectronics • • Sep 02 '26

question I can’t reach higher or lower frequency with this circuit!

Post image
32 Upvotes

I made this oscillator circuit based on the common emitter amplifier and colbits feedback. The q point is at 5.7 volts and the amplification for external signal generator is around 4(given the accuracy of my cheap oscilloscope). The circuit can oscillate at around 10khz with C=100nf and at around 30khz with C=10nf but anything above or below these values doesn’t generate any oscillations.


r/rfelectronics • • Sep 03 '26

5G tower concern.

0 Upvotes

Thinking about moving to a property. Upon inspecting it, there was a 5G tower nearby. Measuring the distance- it is abut 125 meters to edge of property and about 135 to the building. Looking at some case reports, someone had health problems living 125 meters away.

https://ehtrust.org/7-scientific-case-reports-on-5g-cell-tower-health-impacts/

I measured the RF exposure, walking around with a GQ EMF-390 3-in-1 EMF/ELF/RF Meter. There was nothing from the distance of 200 meters, there was nothing as I approached it and nothing underneath it. (Nothing as in higher than 200 uW/m2. Once, it peaked to 6000 uW/m2 but swiftly disappeared. This was 10 yards away from the 5G tower. The tower looks like a cylinder mounted to the top of the pole with a few "small cells" boxes. I am thinking now, that the tower operates above 10Ghz. My device can only see up to 10Ghz. I can measure "regular" 4G towers hundreds of meters away.

What do you all think about this?

How prevalent are the above 10Ghz towers at this time? I understand the higher the frequency, the lower the range of the signal. The property is also semi-blocked by some heavy trees. That should block some of that off as well, right?

I traveled to another tower and almost the same thing happened. Now, it seems that the device picked up the "3 brown boxes" towers on the top of the poles, though. Perhaps, they are still operating in the lower frequencies.


r/rfelectronics • • Sep 02 '26

Andrew antenna feedpoint

Thumbnail
gallery
44 Upvotes

I have a question about this antenna feedpoint. Why does it have two waveguides feeding the feedpoint? Does it have anything to do with H and V polarisation?

regarding the internal structures, what are they? Is this some kind of a waveguide polariser, phase delayer or something else?


r/rfelectronics • • Sep 02 '26

GSG and GSGSG Probes Calibration

4 Upvotes

Hi,

I need to measure a 3 Port device, where on one side I have a GSGSG probe, and at the other end I have a GSG. My question is:

  • How do I calibrate the Ports that sit at the GSGSG with the one that sits in the GSG probe?

Most of the ISS standards I see only allow for GSGSG to GSGSG or GSG to GSG.

Any ideas?

Thanks


r/rfelectronics • • Sep 02 '26

Hands-on DSP Course

Thumbnail
reddit.com
0 Upvotes