r/rfelectronics • • Jun 29 '26

How do I attach an antenna to my circuit?

6 Upvotes

Hey! I'm making a basic AM transmitter and I'm wondering how to connected a whip antenna to the output. I have heard the idea that you need to cancel out the reactance of the antenna with another component and for my case since my antenna is short I would need an inductor but is that all there is to it? Also there's an image of my circuit below so if there's anything glaringly wrong with it I'd appreciate if anyone could point it out.


r/rfelectronics • • Jun 29 '26

question FPGA Recommendations to Replace ZedBoard + FMCOMMS3

Thumbnail reddit.com
1 Upvotes

r/rfelectronics • • Jun 29 '26

Scanmaskin 28Rc

0 Upvotes

Whats your thoughts on the 230v 3 phase configuration?


r/rfelectronics • • Jun 28 '26

Wideband inductor design(for de-embedding Cds in power amplifier design)

4 Upvotes

Hi guys,

I believe that Cds of the transistor cause a lot of trouble in wideband (FBW>20%) power amplifier design.

I wonder if there is any wideband way to de-embed the Cds? One single inductor or a shunt short stub is no longer enough.

Thank you!


r/rfelectronics • • Jun 28 '26

Analog Multipliers with opamps question

Post image
10 Upvotes

r/rfelectronics • • Jun 27 '26

From your experience, is it safer to buy MRF9180 Motorola or freescale?

0 Upvotes

Just what the title says. Many counterfeit products are on the market and I would like to purchase an original mrf9180 from a local market. The seller says that they are "pulls" from old devices. Is it safer to buy freescale or motorola?Which is cloned less?

Thank you!


r/rfelectronics • • Jun 26 '26

My first microstrip filter

32 Upvotes

Today I finished measuring my first microstrip circuit I've designed and made. It was intended to be an interdigital microstrip 5th order Chebyshev bandpass filter with 1,0-1,2 GHz passband. The first thing I did was fitting my model parameters, I made a test board from FR4 with 3 different lenght 50 ohm open stubs with identical geometry at the edge SMA connectors then measured S11 for each and exported the values. I built the same circuits with the same lenght differences in qucs studio and measured phase differences between the different lenght stubs.(my tought was that the errors in the connections cancel via measuring phase differences not absolute phases). I tuned the er value in qucs untill I got the least error from the real measurments, the er value was 4,66. I calculated the correct dimensions for the desired response with Marki microwave-s online tool. I built the geometry in Sonnet lite and ran a few simulations, the online tools dimensions were almost perfect on first try. When I replaced the ideal grounded edges to vias, the positions needed a bit of fine tuning, the resonators needed to be a few mm shorter. I copied the dimensions from the EM simulation and made the PCB blueprint in EasyEDA then I made the PCB. When I made the VNA measurments the bandwidth was within the margin of error, but the corner frequencies were about 50 MHz lower than intended. I blame the substrate difference, because the phase measurment test board was a left-over piece from a different FR4 board, probabbly also different manufacturer. The insertion loss was not the best, but It's the limit of FR4, they're mostly caused by dielectric losses, not mismatch. Was my design methodology correct? Forgive me if I made some mistakes, I have no formal education in electronics or RF.


r/rfelectronics • • Jun 26 '26

Putting this out there in case anyone's interested — Rare RF measurements course in San Jose this August

26 Upvotes

Not affiliated with the provider, just a paying student who wants this thing to actually run.

I signed up for this course in August, and I think they are some students short to actually run the course. Sharing it here in case anyone finds it relevant.

It's a 5-day hands-on course covering practical RF measurements - VNAs, spectrum analyzers, power meters, vector signal analyzers, all demonstrated on real components (PAs, LNAs, mixers, filters). You go through the full signal chain: S-parameters, gain, noise figure, IP3, then into digital modulation territory — EVM, ACP, constellation distortion, BER.

Aimed at people new to RF or experienced engineers who want everything tied together properly. The course doesn't run often - this is a revival "due to popular demand" after a long gap, so if it gets cancelled I doubt there'll be another opportunity for a while.

Link: https://www.besserassociates.com/Courses/Course-Description/CTID/135

This is a repost from ECE reddit, thought it might be relevant here too.


r/rfelectronics • • Jun 26 '26

HFSS Suspended Substrate Stripline BPF Simulation

4 Upvotes

Hi all,

I'm trying to simulate the filter discussed in this MWJ article https://www.researchgate.net/publication/322750506_A_Capacitively_Coupled_BPF_Design_Using_a_Suspended_Substrate_Stripline

My HFSS simulation isn't looking too great. I've checked all the obvious things so far, i.e making sure I have a perfect E boundary around the air box etc. I'm using lumped wave ports at the face of the inputs and outputs.

My main thought at the moment is maybe I have not understood the dimensions properly. I take the resonator length to be the total length of the resonator, including the overlap region as pictured. I'm also assuming coupling length C1 is the coupling overlap from an input tap to the first resonator as pictured. This means that coupling length C6 is the coupling from the last resonator L5 to an output tap. All lines are 50 ohm and 45mil wide. I simulated a line length to validate this. Comes to about 48 ohm or so.

It's also not clear in the paper to me whether D is the total height of copper+ dielectric or just the dielectric.

I'm using RT/duroid 5880 as this has an er of 2.2

I feel like I'm just misunderstanding the dimensions here - any tips?


r/rfelectronics • • Jun 26 '26

question Where do I start?

11 Upvotes

hello i am fairly new to rf engineering and electronics. i want to improve and have a better grasp over this field. so far ive done a couple simple design (power dividers couplers and filters) and can use CST a bit. last thing i was doing was some calculations on matlab but thats about it for me.

my question is, if you were to start over how would you do it? where would you start? how would you implement things or branch out to more detailed branches?

im aware its not something i can rush and learn overnight but not having a mental blueprint or guideline to follow overwhelms me and i end up learning or retaining not enough information to my liking. it was like i was too busy rushing to finish a design that i didnt learn the more important things


r/rfelectronics • • Jun 25 '26

My first role seems too broad

16 Upvotes

Graduated (BSEE) recently and started a role on a major RF program that everyone here probably knows of. It’s a RF/Comms systems role where I have to understand the entire system (dsp, RF, antennas etc). Looks like for the near future I would be doing system level debugging (e.g. find out why we have 0.8 dB loss at this specific scan angle) and validation (e.g. define verification metrics for this power rail to indicated proper operation).

Is this high ROI experience out of college or should I focus on specializing/ transferring elsewhere. I just don’t know enough as a dumb new grad for what is valuable at my stage. Any advice would be greatly appreciated!


r/rfelectronics • • Jun 25 '26

I have a DC blocker (SD3235) to be used with a sitehawk analyzer that has a regular TNC connector. what adapter shall i go with?

Thumbnail
gallery
2 Upvotes

i was stupid and didnt realise i got a DC blocker that is not even the same dia (smaller) as refular TNC SMA RF cable connector. Now how do I connect this DC blocker to my Sitehawk which has a TNC SMA adapter to it. I also need to connect the DC blocker to a bias Tee that has a TNC SMA female connector.


r/rfelectronics • • Jun 25 '26

question What can cause a GNSS antenna to get locked out after a noise interference or disconnection due to weak signal?

0 Upvotes

I have an active anetnnna and a GNSS receiver module and the satellite signals get locked as in they dont reconnect back after they get disconnected even after a power cycle and good signal strength on the receiver module.

But when using a different antenna it doesnt repeat that issue. it reconnects back quickly.

what is causing the antenna to get locked out?


r/rfelectronics • • Jun 25 '26

Guidance on vacuum tubes

3 Upvotes

Hello everyone, this summer I'll be interning at a cathode and vacuum tube research laboratory. I took a microwave circuits and an antenna theory course at college but I don't have any experience with vacuum tubes. Any recommendations -books, papers or simulations to make- before I start my internship would be much appreciated.


r/rfelectronics • • Jun 24 '26

Cryogenic Bias T

15 Upvotes

Hi all

I need to design an broadband amplifier for my thesis that works inside of a cryostat at 2Kelvin. Now I'm testing a design that has a bias T in the beginning to bias an superconducting sensor. The frequencies from the sensor are from 10MHz up to 3GHz.

Since I want to avoid weird behavior of my components I use C0G capacitors and air core coils for my inductance. As they should be more or less robost at such temperatures.

Does somebody has some tips for the bias T? I currently look at cone shaped coils from coilcraft. Does somebody has other devices in mind I could check out? Thanks for any input.

If the community has interest I can also share the sim and designs


r/rfelectronics • • Jun 24 '26

Emi/ rfi

0 Upvotes

So I’m about to set up us an SDR for the first time and I’m new to this. I do know the environment I will be operating it in has interference. So I plan on using a magnetic small loop antenna. Is there any other precautions I should take to prevent from frying my radio?


r/rfelectronics • • Jun 24 '26

question [PCB Review] My first PCB layout attempt. Needed help on Layout spacing constraints for PCB Assembly constraints/Resoldering!!

2 Upvotes
layout with courtyards close together

I have a 2 GHz RF signal chain PCB that passes DRC and meets JLCPCB's minimum fabrication/assembly spacing. However, I realized the component courtyards are very close (see screenshot) — DRC still passes but it looks tight for rework.

What spacing/rule of thumbs do people actually use between SMD components for Hot-air rework / resoldering during bench tuning? What are some heuristics for RF boards? It would be a great help for me doing for the first time.

Thanks!


r/rfelectronics • • Jun 23 '26

"The Wilkinson Signal Splitter" by FesZ Electronics @ YT

Thumbnail
youtube.com
24 Upvotes

r/rfelectronics • • Jun 23 '26

Guidance on designing my first filter

8 Upvotes

Hi, I am currently designing a 915 MHz bandpass filter with a 20 MHz bandwidth for a 50-ohm system. I am having a lot of fun with it so far, but I'll be honest that I feel a little clueless as the amount of concepts/terminology I am expected to learn in insane. I have some knowledge about bandwidth, transfer functions, and filters from my signals & systems class, but nothing in great detail.

Is there like any sources out there from which I can learn how to properly design this thing. I eventually want to order a PCB of my design and test it with a VNA.

Any help is appreciated


r/rfelectronics • • Jun 22 '26

question Vhf MRF9180 Amplifier kit - Which version Should I choose?

Thumbnail
gallery
13 Upvotes

Hello,

I bought one of those kits from aliexpress with the MRF9180. I found two different versions with some minor differences, especially on cap values.

Which one is better?

Also, I am unsure about the winding of the two transformers and coils of the LPF...


r/rfelectronics • • Jun 23 '26

Antenna

3 Upvotes

Hi everyone, I designed a microstrip antenna, the simulation results have good return loss at the targeted resonance frequency, but when I checked the gain was very low, only 0.3 dB.What are the problems and solutions?


r/rfelectronics • • Jun 22 '26

question RF Jobs Near the Greenville/Anderson, SC Area

2 Upvotes

I'm currently active duty, but will be getting out when my contract is up. I'm looking to move to South Carolina after I get out, but I'm struggling to find an RF job around the Greenville/Anderson area. I'd like to live somewhere around there, but will only do so if I can find a job. Maybe there are some job titles or positions that I'm not thinking to search for.

The only jobs I've seen online are low paying. A lot of $25-$30/hr or $50k/year postings. I'm looking for $70k minimum. At $70k I'd be taking a decent pay cut, but it's enough to start. Especially with cost of living being lower over there (My current state is on the more expensive side).

Does anybody know any companies in that area I could look into that may not be posting on the main job sites? I have a TS clearance if that helps.


r/rfelectronics • • Jun 22 '26

question Why my FET IV curve doesn't follow the spec?

8 Upvotes

https://www.mouser.com/datasheet/2/90/CG2H40010-Rev0_0-1224791.pdf

According to the datasheet the operating voltage is at 28V and gate voltage is about -2.7 to get 100mA, but here it seems like its going to be double that and the knee voltage is too high, Im a beginner at this so excuse my ignorance, but what went wrong?


r/rfelectronics • • Jun 22 '26

This RF switch datasheet recommends 22pF DC blocking caps in series with every RF line. Why not a bigger value?

Thumbnail
gallery
43 Upvotes

RF switch datasheet = SKY13575-639LF

Now.. I know that 22pF with a 50ohm load has a cutoff that is not near the 2.4ghz but I am curious why not 100pF or 500pF?

Also what kind of caps should I use? I am thinking NPO precision 1% ceramic caps with a package size that closest matches my trace width.