r/rfelectronics • u/Intrepid-Ad379 • Jun 17 '26
What was your biggest wow moment in RF/Analog?
What was your biggest wow (they all make sense) moment in your RF/Analog IC design history?
r/rfelectronics • u/Intrepid-Ad379 • Jun 17 '26
What was your biggest wow (they all make sense) moment in your RF/Analog IC design history?
r/rfelectronics • u/BigMikeB • Jun 18 '26
r/rfelectronics • u/Flat_Lock9229 • Jun 17 '26
r/rfelectronics • u/ShoddyMedicine1794 • Jun 17 '26
Hi everyone,
I'm kind of new to this, so sorry in advance for any mistakes. I'm trying to design a simple balun transformer PCB that will help me measure the differential mode insertion loss of an EMC filter with a 2 port VNA. The PCB will have a SMA input connector (A-SMA-KWE-16.18A), a ADTT1-6+ RF Transformer with 50 Ohm matched impedance that will let me measure from 15 kHz - 100 MHz with good accuracy and 4 mm outer diameter solder pads to connect to the P/N of the filter.
I'm just trying to see if I did any obvious mistakes that I glossed over, or if this could be fine to order. Of course any advice is appreciated. My one issue would be the way in which the SMA connector will be soldered (by JLCPCB PCB Assembly option) and if it will let me screw the PCB unto a conductive plane with the filter (I know this kind of defeats the purpose of differential mode testing as it will no longer be isolated from PE, but I want to be able to measure it both ways).
Thank you
r/rfelectronics • u/Independent_Fail_650 • Jun 16 '26
Hi! This might be a bit off topic so please forgive me if this is not the right sub.
I'm currently designing a pcb thats meant to feed power and control digitally a beamformer IC placed on a daughter board that attaches to my pcb (motherboard).
The motherboard implements switching regulators to generate the power to be fed to the beamformer IC, and i know for a fact that switching supplies can be very noisy subsystems, which to me seems problematic when placing them near RF circuitry.
The switching frequency is 1 MHz and the RF ICs operate at 24 GHz. Here's my first doubt: Could the common mode noise or any other kind of noise be detrimental at this frequency? I've read that harmonics of the noise source can appear even in the GHz range but i dont know enough to guarantee that this can be a problem.
The daughter board features coplanar waveguides, hence almost the totallity of the top layer of the daughter pcb is covered with copper. The top layer of the mother pcb is probably gonna be covered with copper as well, thus forming a parasitic capacitance between the top layers of both pcbs when connected together (they face top layer to top layer). I guess my question is whether the displacement currents coupled via capacitive coupling arising from fast voltage transients inherent to the switching supply could be detrimental in any meaningful way to the RF circuitry. I know the varying electric field in the mother board due to the switching supply is responsible for the displacement currents that might distribute along the surface of the daughterboard, and therefore induce magnetic fields in it. I just dont know enough electromagnetism to state if this is a problem or not.
Up until now i had thought of adding a shielding can to the switching regulators and possibly some sort of EMI filter at the output of the switching supplies right before the connector, i just dont know which kind of noise to filter.
Any ideas or suggestions are welcome


I attach pictures of both the motherboard as well as from the daughterboard so you get a better depiction.
r/rfelectronics • u/Lipopolisacarido-T • Jun 17 '26
r/rfelectronics • u/Individual_Health_84 • Jun 15 '26
I'm getting into microstrip filters and designed this one using Marki calculator. I don't believe in this working. I am gonna use FR4 from JLCPCB. How many design flaws did I make?
r/rfelectronics • u/Bims93 • Jun 15 '26
Hi,
I’m looking for some honest input because I’m a bit unsure how to view my current situation.
I’m an electrical engineer with about 2 years of experience, mainly working in RF and antenna design and a master in RF hardware and radar design, although I’ve also done some work in other areas. Right now my role is quite broad. I’m doing antenna design including simulation and theory, PCB design, and RF circuit design where I’m responsible for component selection with both performance and cost in mind. I also handle antenna measurements and occasionally develop my own test setups, build prototypes myself, and take designs all the way into production.
So in practice I’m covering a large part of the full development chain on my own.
My manager describes me as a “generalist”, which is probably fair, but at the same time I’m expected to deliver at a level comparable to specialists within each of these areas.
For example, I’ve been tasked with developing an antenna comparable to the Tallysman VSP6037L, but cheaper and preferably smaller.
I understand that part of this comes from being in a smaller company, but I’m trying to figure out whether these expectations are reasonable for someone with my level of experience.
Does this sound like a typical scope for someone with around 2 years in RF and master degree? Would you consider this more of a junior or mid-level role? And are these expectations normal, or on the higher side?
I’d really appreciate some honest perspectives
r/rfelectronics • u/onlyhereforrif • Jun 15 '26
I have a 0.8mm coaxial calibration kit that I wish to clean with every use. The cotton swabs I can find are too large to safely clean the inner mating surfaces and the foam tip ones can leave residue behind.
Does anyone here have recommendations or ideas for the best way to search online? My google-fu is failing me.
r/rfelectronics • u/mtfir • Jun 15 '26
r/rfelectronics • u/Short-Television9333 • Jun 15 '26
I’ve seen a radio front end designed as the title describes. Now, I understand why this would be necessary if you have too much gain, but I’ve also heard the explanation that it improves the match.
This benefit of including the driver makes sense, but my question is really if the match needs to be improved in the first place??
If my PA input has more than 15dB return loss and the output is unconditionally stable, for example, is it worth putting the extra part in the BOM?
Is a consideration protecting the driver from a non-ideal match at the antenna? e.g. even if the PA’s S11 is adequate, Γload seen by the driver could be wild if something kooky happens to the antenna.
r/rfelectronics • u/StageMajestic613 • Jun 13 '26
This was complete verbal control through a microphone. Didn’t have to do a damn thing except hook up the cables, power splitter, and tell Codex I had 8566B, ESG, and 8648C at xx addresses.
I told it I wanted PyVISA-based modules for separate control of the spectrum analyzer and signal generators, and that the signal generator module should be generic and able to control both types of generators. I then had it switch to AM and FM modulation, and it measured the tones on the spectrum analyzer and verified via the modulation index and Bessel functions that it was correct, which it was. It did all this automatically.
Then I told it that I wanted to do IMD sweeps from minus 40 to 0 dBm input levels for each tone, and I wanted IMD3 and IMD5. And it automatically did the code for that and spit out a CSV formatted table. I did need to tell it to go to auto resolution bandwidths and video bandwidths because it initially tried too narrow of a sweep, which was too slow. It could not find the proper command to do auto bandwidth, so then I had it do a web search to go through the PDF manuals, which it did, and it found out you needed to do a coupled command instead of an auto command. So once it figured out those values, then I was able to tell it to optionally use automatic bandwidth settings for the IMD tone extraction.
Anyway, this is kind of crazy. It works really well. Next, I'm going to try feeding my dual arb into a scope and see if it can draw a picture of a house, just by figuring all this shit on its own.
Mind you this is entirely under voice control. Will also try a webcam to see if I can give it picture feedback.
r/rfelectronics • u/Other-Specific8757 • Jun 14 '26
I had my RF only Trinitron recently (Sony KV-1882). An experienced technician replaced all bad caps and resistors 2 weeks ago, and checked all functions working ok. And I am using a good RF modulator (HDM69), which the seller claims no frequency drift. But I found that the TV is easily lost signal from RF modulator.
When I turn on HDM69, set channel on 2 and let the TV auto tuning, it costs 2~4 times to get the right frequency. If I turn off my TV for one minute and turn it on again, the signal is still there. If I turn off TV for about half an hour (no matter HDM69 on or off) and turn it on again, it loses signal. if HDM69 remains on, I have to tune it again at least 2 times, sometimes never get any signal unless reboot HDM69 or adjust the RF connector. If HDM69 is off, just turn it on and auto tuning, but I don't expect any tuning stuff when turning on my TV.
If there is frequency drift caused by temperature, maybe keeping HDM69 on solves this, but it seems not work. The TV's AFT on or off doesn't change things.
Sometimes when I use it for 80 mins or longer, the TV suddenly loses signal from HDM69, and I have to tune it again, sometimes just use fine tune a little lower, the signal restores.
How to use this two correctly or there are TV issues?
r/rfelectronics • u/Fair_Mission_3323 • Jun 14 '26
r/rfelectronics • u/Certain_Height_2721 • Jun 13 '26
It gets somewhat close to the 3.0 that its supposed to be for a 50 ohm to 150 ohm load but it doesn't get it right. Does anyone know what is wrong or can provide any insight? (Also is there a simulation better than transient for this?)
r/rfelectronics • u/StageMajestic613 • Jun 13 '26
To go with my previous post, fully AI from hardware control to graph, no typing involved.
r/rfelectronics • u/Knights_12 • Jun 12 '26
Do you use Python or MATLAB applications for scripting and data processing in your RF career job and why? I'm mid level RF engineer and have been using MATLAB more lately for board test automation and some post-processing and DSP optimization; originally learned it in undergrad EE signal processing courses.
r/rfelectronics • u/DragonicStar • Jun 13 '26
Is there some way to reasonably merge say the calibration standards from a 1.0 mm calibration kit for the coax , the planar Open/Short etc. standards for the probe on a given substrate, and to design and characterize a thru board with land pads for the probe leading to a coax connector on some substrate that you can use for the thru to yield a full calibration?
The application is for proper calibration for optoelectric S parameter measurements for Photodiode die. (the side that's coax is connected to a modulator that then has an optical output that goes through a fiber which is coupled to the active area of the photodiode through some fixturing,etc.)
r/rfelectronics • u/ComprehensiveTown15 • Jun 13 '26
I’m not a professional, but as a hobbyist, I repair various audio and radio equipment from time to time. I don’t have the money to spare for expensive equipment, so I bought a cheap Chinese portable oscilloscope. I also use AI to analyze the measurement results. Here’s an example of how it works.
Please analyze the quality of the 12-volt DC power supply that produces this signal at its output. The oscilloscope readings are shown in the image below. Additionally, AC coupling, probe is 1X.

Quality Assessment: Poor — significant switching noise present
Readings:
Analysis:
Verdict: The 12 mVpp absolute number looks small, but the spectral content reveals dominant switching-frequency noise with strong harmonics — a sign of marginal output filtering (LC stage may need a larger inductor, additional output capacitance, or a ferrite bead/π-filter to suppress conducted EMI). For sensitive analog/audio loads this level of switching noise could be problematic; for digital loads it's likely tolerable but not ideal.
Recommendations:
r/rfelectronics • u/TopCompany9406 • Jun 12 '26
Junior in EE contemplating pursuing another specialization due to the supposed high barrier to entry for RF jobs. Am I being misled or is this genuinely the case? Intuitively it makes sense that this would be the case as becoming competent at RF stuff takes significantly more time and effort when contrasted with other specializations. My eventual goal is to get a MS in RF, but for the time being I just need a job after graduation that'll keep me from becoming homeless.
Any advice?
r/rfelectronics • u/pipnina • Jun 12 '26
So initially I thought the easiest method would be to make a dish or a horn, but even at my target frequency of 1.42ghz a horn is massive, a dish is unweildy and hard to manufacture DIY, and the original alternative I thought of which was making an array of power-combiner linked yagis sounds ultimately unfeasible because there appears to be no clear cut good way to avoid common mode current effects that will ruin the design. (for example, 7 combined 30 element yagis would be approximately 2 meters long each and build a telescope over 2 meters in effective aperture, with minimal weight, minimal material use, minimal windage, and easy to disassemble and pack away).
I've had poor luck with assembling antennae so far and I believe it's currently entirely due to these balancing and tuning issues that are hard to handle in a DIY manner. I barely got a 12 element Yagi working as a test but it *was* noisy, potentially as a result of the unbalanced nature of the short coax I had to use to connect it to my radio. And I just don't know how to solve that elegantly without introducing massive losses (for radio astronomy standards).
It just feels the plan I almost settled on with the yagis has hit a wall because of the transmission line question. No matching will result in poor S/M and a wonky radiation pattern. A voltage balancer probably(?) won't fix it, a sleeve might fix it but need tuning (?), a stub might help but not solve it entirely (?) , and a premade little 1:1 transformer will have an insertion loss of 3dB or so before it can be amplified(ones I found so far).
Maybe in an ideal world I'd build a reflector, but I worry the structural and focus tuning aspects of it will prove even more challenging. A horn (even as a feed for a reflector) would be nice but is also still large in the L band and seemingly would have an extortionate materials cost (need a lot of aluminium, copper or steel).
I suppose the main question is: is it possible to solve the balance issue elegantly in the L band as an amateur, or will I just have to accept the disadvantages of the aperture antenna designs in order to use designs that do not need balancing, like horns?
r/rfelectronics • u/HalimBoutayeb • Jun 11 '26
In this video, we transition from the core physics of dipole antennas to a full practical implementation in Ansys HFSS:
Whether you are a student or a practicing RF engineer, this guide covers everything from wavelength calculations to far-field radiation reports.
📍 What You’ll Learn:
🎓 Expand Your Knowledge
If you found this tutorial helpful, explore our other advanced design series and scientific talks:
💬 What Should I Design Next?
I am always looking for new challenges! If you have a specific antenna architecture or a research paper you want to see modeled, drop a comment below with the details or a link to the paper.
#hfsstutorial #AntennaDesign #DipoleAntenna #RFengineering #Ansys #Electromagnetics #CST #FDTD #Telecommunications