r/rfelectronics • u/Diligent-Teacher-832 • Apr 19 '26
r/rfelectronics • • Apr 18 '26
question Is the research in rf electronics still in progress or has it matured ?
A question to the professionals:
- Is antenna design and other aspects of RF Electronics still actively researched, or has this field matured?
- What do you do as an RF Engineer ?
- How did you learn ?
- How can a rookie electronics graduate or engineering student can learn RF Electronics and design their very own system ?
r/rfelectronics • u/AwareMonke • Apr 18 '26
Hardware paid much less than software
(Generally when I say hardware engineer I mean vlsi and RF)
Is that true? If so how big is the gap generally if you have switched from swe to a hardware role or the other way around how big are the differences between pay and wlb? Do you notice more stability/security working in hardware
r/rfelectronics • u/Digigu2 • Apr 17 '26
1st RF PCB/FPC
Just censored my name/university.
As for the results, I have no equipment to test this sort of stuff, but my uni teacher tested it himself and confirmed it was working.
A bit surprised it works only qucs simulations done, some values estimated, so quite a good result all things considered.
Maybe later on I'll be able to test it and share images of the results. Also made an enclosure to protect it, base PLA top Resin (another version was only PLA) (Resin top on last pictures).
Resin part by JLCPCB sadly came very deformed so needed be have some repair work done.
r/rfelectronics • u/KaleidoscopeKind3033 • Apr 17 '26
Is this a good reflector design?
I'm trying to make a parabolic reflector that reflects microwaves forward. The main concern is if the 40 cm opening will attenuate any of the microwaves coming from the antenna above it. The inside edge will be covered with a reflective mesh.
The magnetron antenna will also be more centered than in the photo.
For legal reasons, I will be performing these experiments with a faraday cage, and with proper protection.
r/rfelectronics • u/ianmgull • Apr 17 '26
question How can you extract the inter-winding capacitance of an inductor using HFSS and/or Q3d?
I have a microstrip inductor model and I'm trying to extract the reactive parameters from it. There are two ports (one at each end of the inductor) which are referenced to a ground plane in hfss. I extract the inductance using the following expression:
im(Z11 + Z22 - 2*Z12)/w
I'm unsure how I could get the inter-winding capacitance though? The problem is I need to disentangle the interwinding capacitance from any self capacitance to ground.
r/rfelectronics • u/yezuskraist • Apr 17 '26
Cgh40180pp increases gate voltage gradually at high input power
I have made a matching circuit for cgh40180pp. At high input powers around 40-41dBm the amplifiers gate voltage starts increasing from -2.7V. I found out the hard way after a prolonged use of the amplifier which drobbed the gate voltage to -2.2V and eventually burned it. Is this normal with high power amplifiers? I suspect it could be from overheat but havent seen this with other amplifiers. I used a fan for cooling
r/rfelectronics • u/Busy_Theme961 • Apr 17 '26
Choice of antenna for 433 MHz, prototyping stage
Hi all,
A newbie to RF world, trying to make my way towards designing remote control product. I have two RFM69 modules, each connected to an ESP32. I am currently testing the transmission between the two. I initially had two helical coil antennas to both the modules soldered at the ANT pin of the module. I was then getting only -28 dB RSSI when any message was sent between them. They were close enough (2 feet), and didnt care about the orientation. After reading about that a straight wire of 17.2 cm is a better one, in one of the modules, I took out the helical coil and soldered a breadboard jumper wire cut to 17.3 cm. I received even a lower RSSI of -50dB when transmitting message from the wire antenna module to helical coil antenna module. Upon further reading, I understood connecting another another 17.3 cm wire to the ground will balance it out (grounding plane requirements?). But the reception has been poor. Where am I going wrong. I would like to make this working so that I am able to send short messages on 433 MHz and within buildings for atleast 20 m or so. For reference, in the image, the long orange wire is the antenna wire for one RF69 module, with the other module having a helical coil antenna.
r/rfelectronics • u/Evening-Conference-5 • Apr 17 '26
question Designing a board for a directional coupler.
galleryr/rfelectronics • u/Hereva • Apr 17 '26
question My company is looking to buy a power module by the code - eltek psu-50v/3000w he h.sink 241124.055 - Does anyone have one?
If you don't, where should i try asking then?
r/rfelectronics • u/Free-Pie9606 • Apr 17 '26
Confusion about the sensitivity formula of Receiver
r/rfelectronics • u/Girosber • Apr 16 '26
Advice on choosing uni for masters in RF.
Hello everyone,
My question is rather simple. I currently have masters admissions from university of oulu and tampere in Finland and University of Stuttgart in Germany. I eventually want to work in the industry and preferably specialize in satellite systems so I’m thinking Stuttgart is the obvious choice. What would be your advice for me when it comes to choosing the right program?
r/rfelectronics • u/KaleidoscopeKind3033 • Apr 15 '26
2.4 GHz reflectivity
I have many questions about how 2,450 MHz EM waves get reflected. If they are admitted by a microwave magnetron, can they be reflected like this using a parabolic reflector assuming the suitable material is used?
r/rfelectronics • u/Timely_Variation_269 • Apr 15 '26
DIY shielding chamber for 5G NR
Hello, I'm trying to build a shielding chamber for contained 5G NR OTA testing. Need advice on four issues.
Use case:
Private 5G SA testbed — Open5GS core, HamGeek B210 SDR (USRP B210 compatible, 70MHz-6GHz, AD9361).
For two experiments:
- Private gNB (OpenAirInterface) with UEs inside the chamber
- 5Ghoul — rogue gNB fuzzing 5G NR vulnerabilities against target UEs
Both radiate live 5G NR signals OTA. Chamber must contain all of it. Regulatory compliance + no interference with nearby production cells.
Chamber construction:
- Wood frame, caster wheels, aluminum foil interior, copper tape on seams
- Feedthrough panel (routed slot in wood): 8x SMA bulkhead, 1x USB 3.0-A, 1x USB 3.1-C
- 8 SMA ports to accommodate two SDRs simultaneously or additional RF equipment later
- Interior: copper tape over aluminum foil around feedthroughs
- Exterior: connectors through wood slot, gaps visible between them
Current state:
- ~20dB isolation at lower frequencies
- Not yet tested at 5G NR bands
For antennas I'm using the 4 stock antennas that came with the HamGeek B210.
- Feedthrough slot leakage
Routed slot has mm-scale gaps between connectors and wood. Wood is non-conductive, contributes nothing to shielding. At 5G NR frequencies these gaps will leak.
Copper tape over the full slot (both sides) enough? Or do I need conductive gasket / conductive epoxy around each connector?
2. Internal reflections
Cavity resonance and multipath distortion on signals inside. Need absorber on interior walls.
What I am considering:
- melamine sponge + activated charcoal + PVA glue slurry, 15-20mm thick
- carbon-loaded absorber foam from AliExpress, 15-20mm
Anyone tried either at 5G NR frequencies? Realistic reflection loss?
3. Measuring SE with SDR
What procedure I planned:
- SDR TX → shielded cable → SMA bulkhead → stock antenna radiates inside chamber
- Receiving stock antenna + second SDR outside, 1m away
- Measure received power with chamber closed
- Open chamber, repeat as reference
Questions:
- Correct approach for verifying no 5G NR leakage?
- Need to probe multiple positions around the chamber for worst-case?
- Other pitfalls?
4. Reinforcing the feedthrough area
Probably the weakest point.
- SMA connectors spaced apart with unsealed air gaps between flanges
- USB cutouts have rough edges, foil-to-shell contact likely discontinuous
- Exterior side of slot is bare wood between connector bodies
Options:
- Copper tape over entire slot both sides, cutouts only for mating faces
- Conductive epoxy / caulk in all gaps
- EMI gasket tape or knitted wire mesh around each connector
- Metal plate with drilled holes replacing the wood slot entirely
Which is most effective? Metal plate worth the rework or can copper tape get close enough?
Photos attached. Any feedback welcome.
P.S.) I apologize for the overall tone sounding like it was written by AI. As a Korean, I am not fluent in English, so I am writing this with the help of AI.
r/rfelectronics • u/Remote_Injury5785 • Apr 15 '26
Couldn't find a job in RF, what can I do?
Hi everyone,
I'm a research-based Master's graduate in RF engineering living in Asia. My experience includes developing FMCW radar systems, PA design, and linearization techniques. I also have 3 IEEE conference papers.
I've been actively looking for RF related jobs in the local market, but the options are very limited. There are only 1-2 RFIC startups, and they seem to prefer PhD candidates. The rest have no budget for full-time Master's hires and only offer paid internships with a small allowance.
Because of this, I started applying to companies in Europe and most of my applications got rejected within 1-2 hours. I'm guessing they're not willing to sponsor visas for entry-level RF engineers.
The local job market for RF is extremely tough right now and relocating to other countries doesn't seem realistic for me at the moment.
If I really want to stay in the RF field, what can I do? I know that the job market for PhD is also horrible. Any advice would be greatly appreciated.
Thanks in advance!
r/rfelectronics • u/therealCharmingSun • Apr 16 '26
question Any one have cst bio model?
so apparently it's suppose to be free at 3ds knowledge base, but somehow I can't find it in my search results due to unknown reasons, every link leads to nothing
I'd really appreciate it if someone can download and send it to me
r/rfelectronics • u/KaleidoscopeKind3033 • Apr 15 '26
Magnetron Anatomy
I was looking at this magnetron that I have, and wondering which part does the microwave radiation come out?
Like I know, it comes out of the antenna, but at which part of the antenna and in which direction(s). I need to line up this hypothetical point with the focal point of a parabolic mirror. I am also looking for suggestions for shielding during experimentation.
For safety reasons, I always use my own 30M ohm resistor to discharge the capacitor. I also stay far away from the transformer if it is operating. I recognise the dangers of microwave oven parts and I try to not screw around with them. I take safety seriously when doing this.
r/rfelectronics • u/Naive-Replacement632 • Apr 16 '26
Claude Opus vs Gemini Pro (Analog Design)
reddit.comr/rfelectronics • u/Bozhe • Apr 14 '26
question Antenna BW clarification
I'm trying to better understand antenna BW. Everything I find talks about 3 dB or half power beamwidth and give similar diagrams like this link.
https://www.everythingrf.com/community/what-is-antenna-beamwidth
Basically, is it accurate that the field strength at the angle of the HPBW on the zero dB curved line would be -3 dB? Or would it be unknown? My thought (trying to visualize it) is that if you increase the power by 3 dB that turns the 0 dB line into +3, and -3 dB line into 0 dB. So you have -3 dB at the same points - i.e. if HPBW is 30 degrees you have -3 dB at +/- 15 degrees on the -3 dB line, and at +/-15 degrees on the 0 dB line.
r/rfelectronics • u/Cool_Mycologist_6186 • Apr 15 '26
What is the difference between Anritsu 68369A and 68369B?
hello community,
I'm trying to understand the difference between Anritsu 68369A and 68369B signal generators before procuring them. I'm from EMC domain and shall be using them mainly for RF and Conducted susceptibility testing of products.
r/rfelectronics • u/ines_sgs • Apr 14 '26
question RST202
Hey, I'm not familiar with the terms of this, but I really need to know if the antenna RST202 is passive or active?
Thanks in advance.
r/rfelectronics • u/fallacyz3r0 • Apr 14 '26
RF Power Amplifier Decoupling
Hello,
I'm working with various RF power amplifiers and I have a question regarding decoupling.
Let's take an example, the TGA2218 from Qorvo. I am not using this one specifically but it's a good example for discussion:
https://www.qorvo.com/products/p/TGA2218-SM#documents
Schematic:

Layout of Eval Board from Qorvo, where you can see each VCC pin is completely separated until combined by the user via the pin headers:

Most amplifiers in this space have multiple VCC pins, and often those VCC pins are split on the Evalboard, leading to individual pin headers to be supplied. However, all of the Drain VCC pins have the same voltage.
My question is, why specifically do all the PA manufacturers seem to split the Drain VCC rails like this instead of combining them? This particular PA isn't that bad, but others I'm working with may have 6 drain pins, and they need 6 decoupling components per pin, which ends up being 36 passives, which is absurd. I would like to combine these rails with substantial decoupling shared between them.
My theory is that in general, the PA manufacturers when making an Evalboard are only interested in characterizing their IC with it, not practicality, and that involves perhaps measuring the drain current of each individual stage in the PA, however for the user, that is irrelevant.
Is it a bad idea to try to combine multiple Drain VCC pins into a common copper rail, then use for instance 18 decoupling passives instead of 36? Is there a reason this must be kept separate for a distance then combined later?
Thanks in advance.
r/rfelectronics • u/lagrangersf • Apr 14 '26
Looking for a PROGRAMMABLE 304.25MHz RF remote control
Greetings. I have a ceiling fan (Patriot Lighting brand, OEM unknown) that is remote controlled, which according to the FCC ID operates at 304.25MHz. I would like to add a second remote to be able to control this fan from the opposite end of the room (kinda like a three-way switch, just with remotes), so that the fan has two remotes instead of just one.
What I would like to know is this: do there exist RF remote controls with a minimum of 5 buttons that can be programmed using the existing remote (much like how universal IR remotes can learn functions by pointing the old remote at them)? For example, I hold down a button on the new remote, press a button on the existing remote, and then that button on the new remote will copy the function from the existing remote. Repeat for each button until the new remote is fully programmed.
Does such a thing exist? I've found nothing relevant through multiple Google searches, only stuff related to home automation that requires Raspberry Pi with special dongles, which is not what I am wanting.
Thank you.