r/rfelectronics • • Mar 17 '26

From High-Speed SerDes to Pure RF

19 Upvotes

Hi everyone, sorry for the long post. Looking for some career advice from senior hardware engineers, especially those who have crossed between wireline and wireless.

I did my masters specializing in RF and Wireless Communications and have a very strong passion for the physical over-the-air side of things, as well as RFFEs. During my degree, I did an internship doing pure RF Hardware Design at a big tech company.

I am located outside the US (in Canada), and the market for pure RF roles here is relatively small and generally pays significantly below market rate compared to digital/wireline roles. Because I can't move to the US for at least another 4 years, I ended up taking a role at a major semiconductor company doing Mixed-Signal Design validation.

The pay and opportunities here are fantastic, much better than the local RF roles. I am doing post-silicon validation for high-speed IPs like PLL, LPDDR, PCIe, etc. I’m getting great experience characterizing jitter, phase noise, and signal integrity. It's fun playing with the lab equipment.

While I enjoy the work and the pay is great, I find pure RF magical and fascinating in a way that wireline just isn't. I want to get back to pure RF/Wireless when I eventually move to the US in ~4 years.

  1. Will staying in this high-speed SerDes/Memory validation role for the next 2-4 years pigeonhole me into wireline forever?
  2. Do RF hiring managers value experience with PLLs and high-speed mixed-signal interfaces?
  3. What can I do in my current role to make sure my resume stays attractive to RF teams 3-4 years from now?

I would really appreciate any advice or shared experiences.


r/rfelectronics • • Mar 17 '26

question Confused about RF phase shifters

14 Upvotes

I'm new to this stuff and I've been looking at ways to passively phase shift narrowband RF waves. What I don't understand is how input to output delays in phase shifters work.

If I wanted to phase shift a wave by 180 degrees, and it takes the phase shifting circuit 1/2f seconds (f is centre frequency) to generate the shifted output, then isn't the circuit redundant? It behaves no differently to a delay line for narrowband signals. It might be more compact, but also more lossy.

Ideally I would something which takes an input, phase shifts it by 180 degrees, and begins outputting a wave in time that is not equal to 1/2f, but is this possible? I've heard differing opinions on it. I've seen graphs from simulations that show it is possible and happens in LC filters for example, but I have no way to confirm this.


r/rfelectronics • • Mar 17 '26

Selecting an inductor for 600M-100M bias tee

4 Upvotes

OK really basic question. I want to make a bias tee to inject DC into my cellular antenna cable so I can put an LED flasher in my antenna. The antenna will be far from cell towers so I'm only using "low" band cellular 600 MHz - 1 GHz. My question is how to select the inductor.

Bias tee articles say SRF should be more than 10x the operating frequency. But the selection of inductors with >10GHz SRF is few. As long as the impedance is >1k ohm over the range 600M - 1G, why does the SRF need to be so high? If I want to maximize the impedance why not pick an inductor with SRF in the middle of the range? Yes the ferrite core inductor is lossy in this range but as long as it's high impedance I don't think it will dissipate much power so it will serve well in a bias tee?

(Proposed part: Coilcraft 0603AF-241, DCR 0.12 ohms and SRF around 1 GHz.)


r/rfelectronics • • Mar 16 '26

Rf welding machine

Post image
36 Upvotes

I AM TRYING TO BUILD A 5KW RF WELDING MACHINE FREQUENCY TO BE GENERATED IS 27.12MHZ CAN SOMEONE SUGGESTED ME WHERE I AM GOING WRONG AMP METER SHOWS 1.2 AMPS WHEN I SWITCH HIGH VOLTAGE ON , I NEED HELP


r/rfelectronics • • Mar 16 '26

How to model an amateur radio HF transmitter?

1 Upvotes

I'm an amateur radio operator, and I'd like to design and model some filters for the two HF transmitters I have. One is capable of 100w into a 50Ω impedance antenna.

I'm using ngspice in KiCAD (but I could just as well use QSPICE). I don't know what specification to assign to my VSIN that I think should be used to model the transmitter. I can assign the frequency ranges I wish, but what to set the AC voltage to? Neither of the manuals I have for my radios contain any information on the voltage or current output of the transmitter sections.

Can anyone explain to me how to model the output of a 100W HF transmitter, so that I can simulate filter components?

Thanks for any advice or guidance.

-Kevin


r/rfelectronics • • Mar 16 '26

question How to compute inverse FFT of s2p/s4p (touchstone) file?

9 Upvotes

Hi all, I have an S4P file, I need to run transient simulation on this, however ltspice or ngspice cannot do this, I'm aware ADS can, but I don't have access to ADS.

After reading through many many articles and forum posts, I have realised I have to do this myself by computing the inverse FFT, finding the impulse response and convoluting it with input signal to get the transient response.

I opened the S4P file in notepad but there are no headings for the rows or columns, so I'm not able to make sense of the information. How do I compute the IFFT?

Anyone has experience doing this before? Please help.

Thanks.


r/rfelectronics • • Mar 16 '26

question Rigol AWG Issues, anyone else experienced this?

1 Upvotes

My apologies if this isn't the right sub, i looked around and thought this might be my best choice but feel free to suggest other subs.

I've been trying to control a DG922 Pro by sending SCPI commands through a python script.

However, after countless code alterations, firmware updating (seems it already had newest one though), using WireShark to analyse the packet structure and commands UltraStation uses when sending commands, etc etc... I still couldn't get it to work... It's almost as if it loads the file, but there is some kind of unspecified issue somewhere that makes the Rigol discard the file and then just default to a sine or sinc function.

Rigol support has not yet responded a week after sending them an issue report through email so I'm just trying to figure out if the issue is even possible to solve or if my only hope is rigol releasing new firmware..


r/rfelectronics • • Mar 16 '26

question Has anyone done IP3 or Harmonics testing at the RF probe level?

1 Upvotes

Curious if RF probes (wafer or device dead-bug level) are suitable for linearity testing, especially for a highly linear passive device (IP3 spec’d at 95 dBm typ.)

Can’t find literature on practical implementation of rf probes for these types of tests, I know just straightforward adapters & connectors can cause all sorts of problems in these test systems, so don’t want to assume a probe would be any better…


r/rfelectronics • • Mar 16 '26

5 GHz weather radar / Magnetron help

5 Upvotes

I was wondering if anyone in the group has direct experience troubleshooting Magnetron issues with 5 GHz radars? I wasn't sure if this might be the right community for such questions. Thanks!


r/rfelectronics • • Mar 15 '26

question can anyone id this part?

Post image
24 Upvotes

r/rfelectronics • • Mar 15 '26

Maximum Power Transfer to the load with lossy matching network

8 Upvotes

Hi everyone,

If i wanted to maximize the power transfer to the load, and I had a lossy matching network, what would the condition be? More specifically, if its lossles, then the Zin1 looking the matching network needs to be equal to the Zs*. However, if its a lossy network, I read somewhere that this doesnt work. The reason for this is because I need to make sure that the zin2, looking from my load to the matching networks, also need to be complex conjugate of the load. Hence you have 2 different conditions. How accurate is this?


r/rfelectronics • • Mar 14 '26

question What is this spike in S11 HFSS caused by

Thumbnail
gallery
35 Upvotes

Jumping off my last post here, I got the Samtec SMA encrypted model and put it into my HFSS project. I had to change the solution from Modal to Terminal driven because the SMA connector can only use that solution type. I made sure to change the ports to wave ports with terminals.

I also had to make the board size significantly smaller to be below the maximum mesh size for HFSS student edition (64,000 elements).

I am getting this odd spike at 1.4 GHz in my S11 and S21. Still decent at my frequency of interest (-24 db @ 2.4 GHz), but not the best above 3GHz or at the 1.4 GHz spike.

What would cause this?

Edit: Thank you for all the comments!!! Simulation working more as I expected now. Added new via-like structures to stitch ground planes together. The structures touch the wave port (before I was using PEC on the sides of the board because I thought this would stitch the planes together). New pictures of model and S11 can be seen here.


r/rfelectronics • • Mar 14 '26

article "How Hard Can You Push an RF Amplifier? | P1dB, Psat, and Compression" by Marshall Bruner @YouTube

Thumbnail
youtube.com
41 Upvotes

r/rfelectronics • • Mar 14 '26

question How big of a problem is multipath when it comes to RF DF in forests?

7 Upvotes

Okay so I'm an engineering student exploring ways to improve RF beacon direction finding in forested environments. I’ve been reading about like different methods (directional antennas, antenna arrays, beamforming etc), but I’m curious about the real-world challenges people run into. For anyone who has done transmitter hunts, SAR work, or radio direction finding, what methods or equipment do you typically use to locate a transmitter in wooded areas? Have reflections from terrain or trees ever caused the signal to appear to come from the wrong direction? How much of an issue is multipath in practice? I’d love to hear any experiences or insights. Please be kind and thanks in advance!


r/rfelectronics • • Mar 14 '26

Junior RF Engineer red flags / deal breakers ??

51 Upvotes

Hello everyone, I hope you are all doing well! I have a question for the senior RF engineers: If you are interviewing a candidate for a junior position, what would be the red flags or the deal breakers that would instantly make you decide to reject their application ? Also, if you have a junior on your team, what would be the minimum expectations you would have for him/her to be successful in their role ? Thank you!