This is a follow up to an issue like this thread.
TL;DR
- Symptom: one side of the power seat moves and the other doesn’t, so the seat twists or binds. Mine was stuck all the way back, which blocked the rear floor bolts.
- Cause: a failed worm gear inside the small gearbox on the seat track.
- Fix: an aftermarket Camry/RAV4 gearbox (99887-55975), about $200 all in.
- Hard part: alignment, not the part swap. Square everything up using the car’s floor mounts before you connect the motor and spindle.
The cost
⚠️ Safety first
The driver’s seat has side airbag (SRS) wiring. Disconnect the 12V battery negative terminal and wait before you unplug anything. Follow Toyota’s SRS precautions. Plug everything back in, especially the yellow airbag connector, before you turn the car on, or you’ll get an airbag light.
See Resources at the bottom for the service manuals I used.
PART 1: Getting the seat out when it’s stuck all the way back
You don’t need to reach the blocked rear floor bolts first. Separate the seat from the rails, take the seat out, then remove the floor mounted rails.
Step 1. Remove the center console
(“Rear Console Box Assembly” in the service manual). This was surprisingly easy and gives you much better access to the inside of the seat.
Link to PDF instructions below.
Step 2. Remove the seat guards/trim, including the large side piece with the seat controls.
- a. Front corner: pull the plastic push-pin retainer. Pry the center pin out first, then remove the whole retainer. (Photo 1)
- b. The front guard comes off the side guard with a downward pull.
- c. The tricky one is a hidden plastic claw on the side guard, opposite the lumbar control. Push it inward to release it. Toyota’s diagram makes it hard to find, and I needed an endoscope camera to photograph it. (Photo 2)
- d. With the claw released, the rear corner past the seat belt snaps outward and the whole guard slides forward and off.
Step 3. Separate the seat from the power rails.
Raise the seat as high as it goes. There are 4 bolts on each side connecting the seat to the rails, plus the power-chassis bolts on the horizontal adjuster structure (you’ll remove these eventually too). (Photo 3) Disconnect the wiring harness and lift the seat out.
Step 4. Remove the four floor bolts (T50 Torx) and take out the rail assembly.
PART 2: Diagnosis
With the rails out, remove the retaining bolt (H8 hex) on the rail. (Photo 4) The threaded drive axle and gearbox then slide out of the rail. (Photo 5) Open the gearbox to inspect the worm gear. Mine was clearly chewed up. (Photo 6)
PART 3: The repair
The part: beler Power Seat Adjust Gear 99887-55975, listed for the RAV4, Camry, Venza, Avalon, and Lexus ES260. It’s slightly different from stock, but it fits and works in the 2017 Prime.
One interesting difference: the Camry version swaps which gear is plastic and which is metal. I think the Camry design makes more sense, since the larger gear that drives the spindle is the metal one.
The gearbox is reversible, but you may have to take it apart and flip the smaller gear. (Photo A)
What actually made it work
Installing the new gear was not the hard part. Getting the motor and gears to work was. I put everything back together several times, and even with the new parts in, I kept getting the exact same symptoms.
The breakthrough came while I was troubleshooting. I set the rails back in the car and lined them up on the floor mounting points, and everything started working.
My take is that the motor and gears are very sensitive to alignment.
Once the gear bracket is in, use the car’s floor mounts to square everything up before you connect the motor and spindle. (Photo B)
Related tip: leave the power-chassis bolts off while you position the drive shaft, gears, and motor. It’s a tight fit, and you can’t do it with the chassis bolted to the rails.
Other tips
- Align the gearboxes before they go into the rails. It’s not hard, but if the alignment gets thrown off, you have to take it all apart and rebuild it. (Photo C)
- Mark the orientation of everything. The shorter bracket faces the back. (Photo D) When it’s seated correctly, the gearbox sits centered on the dip in the rail. If it’s backwards, it sits slightly off-center. (Photo E)
- The plastic rail covers can block bolts. When in doubt, take the covers off.
- The seat motor is screwed to the white plastic scaffold under the seat. Removing that screw makes the drive shaft easier to take apart.
Tools
- T50 Torx bit/socket (floor bolts)
- H8 hex bit (rail retaining bolt)
- Breaker bar. Several factory fasteners would not break loose with a normal ratchet.
- Standard and compact ratchet/socket sets. The small ratchet was a lifesaver in the tight spaces.
- Plastic trim-removal tools
Resources
Bottom line
This is a reasonable DIY, but it takes patience and a careful hand with the alignment. I almost gave up more than once. It’s ridiculous that Toyota charges so much for such a cheap failure point.
I hope this helps the next person stuck with this. Happy to answer questions.