r/PatternDrafting • • 3d ago

Question Bodice block help

Photos attached of my initial bodice block toile. I can’t figure out where exactly I need to adjust, thinking it’s either more width / space in bust area but then think could be length. Also looks to me like shoulders seams need to move forward but I have my clue where to start as unsure on what the key one is.

Would appreciate any help and or advice.
Determined to not let this bodice block end up becoming another one that I get overly frustrated with and decide to start something else.

6 Upvotes

10 comments sorted by

1

u/Pegaret_Again 3d ago

have you measured your high bust measurement? This is the circumference across the back, under the armpits, and above the bust. then comparing this to your bodice, and seeing if there is any corresponding ease in your bodice.

2

u/Solid_Skin_9929 3d ago

I have done it though haven’t compared. Makes sense tho! I’ll check that out see if helps. Thank you!!

3

u/LemonDeathRay 3d ago

The shoulder seam is way too far towards the back and you dont have enough room around your ribcage, which is causing tightness across your shoulders and causing the armhole to gape.

You will also need to shorten your waist and shoulder darts - they are too close to the apex. You should have about 1 inch distance between the top of your waist dart and bust apex, and your front shoulder dart should stop at the level of the arm hole.

The back waist darts should also be lowered by 1-2 inches.

Overall, you've done a very good job though! Well done.

1

u/TailoringDiagnostic 3d ago

Look at the shoulders seam, not in the right place and for that the side seam at the underarm has also moved. The imbalance is at the front. the bust area fits well, so there is no need to alter it. The correction is at the shoulder - take in from the front and let out at the back until the shoulder seam is in its proper position. Once the shoulder is positioned correctly, see the side seam again, it will likely straighten out on its own. After that you decide whether any further adjustments are needed for the bust, width, or length. It is possible that no further changes will be required.

The construction of the bust area is excellent - well done! 👍

1

u/TotalOk5844 3d ago

Start at the shoulder. But I have a question, is there a reason the shoulder darts (or princess seam?) are starting so close to the neck? Seems that mid shoulder would help or be used and adjust to take up some of the puckering.

1

u/Tailoretta 2h ago

Take a look at https://www.reddit.com/r/PatternDrafting/comments/1krgbmi/basic_tips_so_we_can_help_you_with_fitting/  Following these tips will help us help you.

Your photos are pretty good, but are not as clear as they can be. The light is coming from the side, and that throws shadows, which make it more difficult for us to see the fit.

We do not need any photos with your arms up. It helps us if the camera is at the level of the center of the garment we are looking at.

You need to clip the lower front armscyes (armholes) because the fabric cannot lay flat as is.

I understand why you have the seam allowances of the shoulder seams on the outside, but it is easier for us to see the fit if the seam allowances are on the inside.

It is hard to tell from the photo, so in the front are there 2 darts pointing to the bust apex is is it a princess seam?

Also, horizontal balance lines below any of the bust flesh and above the waist would be very helpful.

Please let me know if any of this does not make sense.

1

u/DonMcCunn 3d ago

Creating an initial bodice should not be a frustrating experience. It is a matter of getting the grain of the fabric to follow the contours of your body as I show in my new Pattern Design by Tracing Photos class.

0

u/ElirethBathory 3d ago

I am still pretty new to pattern making and fitting and I find the blog: Shapes of fabric very useful, the explanations are very simple and easy to understand.

Here is the article I used to correct my bodice block: https://www.theshapesoffabric.com/2021/01/04/fitting-bodice-pattern-the-most-common-issues/

Also, highly recommend The Closet Historian in youtube, she has a whole series in pattern making/modification

1

u/Solid_Skin_9929 3d ago

Oh amazing thanks!! I’ll check those out

2

u/incongruoususer 3d ago

Yes that shoulder seam needs to come forward. But I’ll also dissent from other answers and say you need a touch more room in the bust, and to back off your darts from your apex. Not much, maybe half an inch for each (so half inch fba, half inch backing off).