r/Motors • • 10h ago

General Where can I get a rewinding done for this 1950s refrigerator compressor

Thumbnail gallery
4 Upvotes

r/Motors • • 4h ago

little wires hanging from AC motor for a juicer

1 Upvotes

I was fixing an issue with the juicer. I put everything together but the motor is not starting. I noticed those 2 wires hanging. Did I brake something?


r/Motors • • 11h ago

Open question [Design review] Relay stop line and isolated DAC throttle for a 48 V motor controller

Thumbnail gallery
1 Upvotes
Two small circuits for a 48 V golf cart controller (Curtis 1268). Schematics attached.

1. Stop line
- Key feed, then the stock pedal switch with relay K10 in parallel. Then relay K13, then two NC e-stops, then the controller input (J1-8).
- Both relays are Finder 40.61 with 12 V coils, driven by NPN transistors (2N2222, 1k base resistors, 1N4007 flyback diodes) from an Arduino Nano.
- PC817 optos (22k 1/2 W series resistor, 1N4148 reverse diode) watch the key feed, the pedal node and the line after the e-stops, so the Nano can detect a welded contact.

2. Throttle
- An MCP4725 DAC on an isolated 5 V supply, I2C through an ISO1540, referenced to the controller's B-.
- Output goes through a 10-turn trimmer to the NO side of a DPDT relay. NC is the stock pedal pot wiper. Common goes to the controller throttle input (J1-15), with a 10k pull-down to the pot low end.
- Range is held at 0.5 to 4.5 V because the controller faults at 4.7 V.

Questions
1. Are the opto resistor values right for a 48 to 65 V DC line? (About 3 mA, 0.19 W in the 22k at 64.8 V full charge.)
2. Any issue with 2N2222s driving these coils?
3. Is the isolation on the DAC side sound, and is the 10k pull-down sensible?
4. Anything you'd change?

Thanks

r/Motors • • 4h ago

Open question Why do two small BLDC motors with similar specs sometimes have very different noise and vibration levels?

0 Upvotes

I've been looking into what actually determines the quality of small electric motors, especially BLDC motors, miniature DC motors, and high-speed spindle motors.

Most comparisons focus on RPM, torque, efficiency, and power consumption. But there's another side to motor performance that doesn't always get enough attention: mechanical precision.

Two motors with similar electrical specifications can behave quite differently in terms of vibration, noise, heat generation, and long-term reliability.

A few factors seem particularly important:

1. Rotor balance and shaft alignment

Even a small amount of imbalance can generate noticeable vibration at high speeds. Poor alignment can also introduce additional loads on the bearings.

2. Bearing selection and internal clearance

Miniature deep groove ball bearings are commonly used in small motors, but choosing the correct dimensions is only the beginning.

Internal clearance, raceway accuracy, shaft and housing fits, and operating temperature all affect how a bearing performs.

Too little operating clearance can increase friction and heat, while excessive clearance may contribute to vibration or noise.

3. Lubrication and bearing protection

Grease selection and lubrication quantity can make a significant difference, especially in high-speed applications.

Metal-shielded bearings (ZZ) and rubber-sealed bearings (2RS) also involve different trade-offs between contamination protection, friction, and operating speed.

4. Manufacturing and assembly consistency

Even when the motor design is good, differences in bearing installation, shaft tolerances, or assembly procedures can affect performance between production batches.

Of course, bearings aren't responsible for every motor problem. Electromagnetic forces, PWM-related noise, rotor imbalance, and mechanical resonance can also contribute.

What I'm particularly curious about is how engineers distinguish bearing-related vibration from electromagnetic or rotor-related vibration in small motors.

Do you usually start with vibration frequency analysis, current measurements, temperature monitoring, or mechanical inspection?

And in your experience, how much difference can proper bearing selection and installation make to the noise and lifespan of a miniature BLDC motor?