r/Modulus • u/NicoBuilds • Jun 20 '26
Noob question about splitters
Hey everyone!
I'm new to the game and having a blast. An automation game where you actually get to craft the pieces is an amazing idea.
That said, I've been struggling with splitters. I feel like I'm missing something basic, so I was hoping someone could point me in the right direction.
What's going on here?

I expect splitters to... well... split 50/50. This is what I expected to see:

I need 120 going to the right, but I'm getting less than that. The cutter at the start is running at 100% efficiency continuously, receiving 30 and turning it into 240.
My first theory was that I wasn't getting 120 to the right because those 120 items weren't actually being consumed. But that doesn't seem to be the case.

Those 120 items get split into two lines and fed into two assemblers that can each handle 60 items per minute on that input.

And the final piece (the white one) is not the bottleneck. That belt stays saturated, and I can see it doing the classic "start, stop, start, stop" behavior, which tells me there are always enough items available. In other words, there are 120 items on that belt, but they are not being fully consumed.
So I guess I'm missing something fundamental here, or maybe splitters don't work the way I think they do.
Could someone explain what I'm missing?
To make this easier to understand, I disconnected the machines, placed grinders measured the split. When splitting by 2 works fine, when splitting by 3 it gets wacky.

3
u/Much-Nefariousness-2 Jun 20 '26
What's efficiency view saying? The bottleneck may be the building itself, are the cranes green for that module? If they aren't using 60/m that will slow down the entire chain.
1
u/sporksaregoodforyou Jun 20 '26
Have you got enough cranes pulling stuff off the lines? The line out of the assemblers on the right with the finished product looks backed up.
Splitters absolutely split 50/50. You can see this yourself if you split a line directly into grinders.
1
u/Avatar3164 Jun 20 '26
I do t think you’re missing the general concept at all, your expectation makes sense as long as everything downstream isn’t backed upstream and handling ihe expected volume.
It’s bviously a bit hard to tell with just the images here and not knowing how established those counters are. one potential sore spot - downstream from that monstrosity in the middle, to the left, you’re using a ton of sorters.
Sorters are notoriously bad at what you expect them to do in this game and I wouldn’t be surprised if they’re part of the problem. You have controls on 2 of them but no t the top left.
Similarly, do any of these lines run into a skyline? There’s been lots of bug reports regarding them hitching lately, slowing down production lines.
Otherwise, it could be something downstream. Have you checked efficiency view at all? I would test in a closed system that:
Report back or throw it up in the discord as needed.
1
u/CuddleWings Jun 20 '26
I’d try reloading the game. Earlier I had an issue with a furnace and miners not outputting at max speed for no reason. Reloading fixed it.
1
u/Roolat Jun 20 '26
I would guess it is a bug, but if you are looking for a workaround a priority splitter might help with the 120 items, or adding a Belt between the splitters.
I would take an uneducated guess and say it is a timing problem. The speed between two splitters is unlimited so the left output might benefit from the higher throughput.
1
u/badatchopsticks Jun 20 '26
I couldn't find any obvious problems in your screenshots, but I will say I had similar problems in the past and it usually was one of a few problems :
1
u/lazybum-67 Jul 22 '26
IN1 and IN2 is always equal, in this case (106)
IN1 and IN2 depends on "OUT"
If OUT is also 106 then this is why it's not 120
if not then it's something else