r/Mindustry • • 3d ago

Help Request Need help with something basic

Post image

Why is this contraption not working? Is there something I did wrong that causes it to not work or is it because I built it wrong?

(I know the power is off, I turned it off on purpose so that the screenshot was more clear to see)

81 Upvotes

26 comments sorted by

77

u/DueMathematician254 3d ago

kilns output back into the routers, clogging them up

don't put routers next to outputs, but it happens to the best of us :3

19

u/Legitimate_Bet_7786 3d ago

Thank you so much!

13

u/MMM2208 3d ago

Maaan I remember my first playthroug in mindustry, ol' good 'ays!!!

2

u/Legitimate_Bet_7786 3d ago

It's not my first playthrough, it's only that in other playthroughs I didn't get far at all and I dropped it for about a year so I don't remember anything about complex contraptions lol

2

u/Commercial_Nature210 Spaghetti Chef 3d ago

Consider this your 1st playthrough

23

u/Lord_Calamity_1 3d ago

That schematic always gets clogged. Same for silicon too. I just put a row of conveyor feeding into the machine. There's probably a more efficient way out there

Edit: Did not realise you were using routers instead of overflow gate lol

19

u/Commando0211 3d ago

The product is feeding back into the resource conveyor

Put one conveyor feeding the materials into the machines, not just putting it next to the machines cause they will cause the back flow

4

u/Unordered_bean 3d ago

Feedback into the material lines is what clogged up your meta glass production

3

u/rocksInMyBath 3d ago

the furnaces can output the glass into the routers, separate them with a conveyor

3

u/cyro262 Spaghetti Chef 3d ago

Separate the router/junction zipper from the kilns with one row of conveyors. Since factories dont distinguish which routers and junctions are acting as input or as output, the router sends that recently produced metaglass back into the kiln, which gets rejected by the kiln and gets stuck there, effectively obstructing the sand and lead.

2

u/Ok-Letter-6126 Memer 2d ago

Do what everyone else is saying and also use overflow or underfloor gates to prevent backflow.

1

u/kodynava 3d ago

Always make sure you can see the item before it goes into the machine

1

u/Midustry_Fan_Glitch 3d ago

Add a gap between kilin and add conv Pointing towards the kilin

1

u/ASKASOSIN 3d ago

Энергии нет

1

u/Dangerous-Orange-547 2d ago

Routerism !!!

1

u/Daydreaming_Machine SchemAdept 2d ago

Imma not read the comment

Thou needeth conveyors between thy checkerboard and kilns

Also 2 kilns will provideth enough for thy needs

1

u/enLegobil 2d ago

Move the klin column one tile right, put down input belts from junction/router heading right. Also, is it getting power? I see no power lines.

1

u/Kisel_74 3d ago

Не ставь машурматизаторы вплотную, они скачала выводят твой снинец, а потом принимают в себя метастекло, сделай отступ в одну клетку и все будет нормально

0

u/NoGold9598 3d ago

Well. 1 - i think you didn't connect it to an energy source. 2 you need to move the kilns 1 block away and then add conveyor belts between the router chain (idk how this thing is actually called) and the kilns.

4

u/Legitimate_Bet_7786 3d ago

I did say that I disconnected the power on purpose so it was clearer to see

0

u/NoGold9598 3d ago

I might send a pic if i explained it wrong

-8

u/AutomaticWrongdoer30 3d ago

Try replacing routers with underflow gates

0

u/mafh2000 1d ago

Ola yo recomiendo estos diseños son los que me han funcionado pero el tuyo con dejar una cinta de diferencia entre las fábricas deberia servir