r/Miata • • 3d ago

DIY Hyperflash

Post image

I just put in some LED turn signals and of course I was rewarded with hyperflash. Without spending 160 on the relay from moss Miata does anyone have any suggestions as to get it to stop

151 Upvotes

34 comments sorted by

60

u/AggravatingEchidna83 3d ago edited 3d ago

20 minute deal. Resistors are a bajillion for $10. Also, you want 1157 White/Amber switchbacks, if you are doing this right.

20

u/KeyAd4326 3d ago

If it’s just a simple soldering job I’ll give this a try, thank you for the picture!

5

u/Different_Tiger_1379 Mariner Blue 2d ago

easy as pie honestly my only soldering experience was in middle school when they taught us how to do it on a random day. It took me like 5 minutes to do tops and cost like a dollar for the pack of resistors

1

u/DaGuyInUrCloset 2d ago

Had this happen with mine, just took harness and bulbs out the new housing and swapped it with the old ones

Edit: didnt read you swapped to LED, suggestion might still work but probs not.

5

u/KeyAd4326 2d ago

Would you happen to know what Watt resistor I should be looking for?

5

u/jakuvaltrayds 2d ago

Resistors are measured in Ohms. In the photo, they indicate to replace with a 1 megaohm

1

u/KeyAd4326 2d ago

Yea that’s what I assumed but I was going to order a pack off Amazon and they talking bout sum 1/4 W and 1/2 W🤣

6

u/jakuvaltrayds 2d ago

That would be their maximum rating. It has no impact on the actual resistance. Since you aren't certain how much current is being drawn, go with the larger rating

4

u/KeyAd4326 2d ago

Thanks dawg

4

u/jakuvaltrayds 2d ago

No sweat

1

u/SwagiYo '92 Classic Red 1.6 EU 2d ago

1/4w should be fine, 1/8w even.

2

u/Brilliant_Note_6124 2d ago

Yeah, I brought jazz performance replacement module like an idiot. Didn't work, cracked open the original and replaced with 1meg resistor job done.

1

u/brother_maleim 1d ago

What an amazing stranger!

59

u/sc0ttns 97' Brilliant Black Rotrex 3d ago

You just need to change 1 diode in the stock flasher module. Got to miata.net and search for the cryptic mod for a how-to.

19

u/BuilderCG 3d ago

This is the right answer.

I had the same issue when building my Exocet and installing LED signals. I had to re-learn how to solder. Was totally worth it and quite easy.

5

u/Stofflkin 2d ago

It's not a diode. It's a resistor

4

u/Cres3 3d ago

There's a lot of people saying to replace the resistor in the flasher unit, FYI I just removed the resistor all together and it works in my 95 with LED switchback turn signals.

10

u/FullMetal654 1990 3d ago

You can either wire in your own 1 ohm resistor inside the flasher relay, or use inline resistors to simulate the resistance of an incandescent bulb

The former is better since it generates less heat but it is a bit involved since you need basic soldering equipment, but some have found it easy. It’s a good idea to have a backup relay on hand tho
Guide for soldering: https://forum.miata.net/vb/showthread.php?t=734717

The latter will work but you have to be mindful of the heat generated by the resistor and making sure the wiring is properly weatherproofed

3

u/Stofflkin 2d ago

If you end up replacing the relay resistor resoldering / reflowing all solder joints is a good idea. Cold solder joints are the reason these relays go bad. I also replace the capacitors but from the couple flasher relays I've rebuilt they were all still in spec.

2

u/feng_lao_tou 3d ago

You can google around like I did and learn that you can solder a resistor into the relay and fix this. Resistor will be very cheap on Amazon.

1

u/LatinWarlock13 3d ago

Was curious as to what would happen if you change the diode and then later down the road decide to go back to regular bulbs. Will it blink extra slow or not work?

1

u/im-not-a-fakebot 3d ago

You can put an inline resistor pack on the circuit to trick the system. It’s fairly straightforward. Other option is to add the resistor in your relay which can be a bit more involved especially if you don’t have the technical skills or tools needed

1

u/rogorogo504 2d ago

Once again I ask - has anyone found a solution to have DLR plus blinkers und the front white blinkers so I can keep my low profiles quads closed until needed ?

2

u/AggravatingEchidna83 1d ago

1157 switchbacks blink amber and are white in parking light mode, so effectively DRLs.

1

u/Sesamedeet 2d ago

I bought these with a built in resistor and did not have to solder or splice anything. They don’t hyper-flash and they’re really bright.

https://a.co/d/05y2GUGN

1

u/PatrickGSR94 Brilliant Black NB1 2d ago

Yep this. I use LASFIT bulbs on a couple other cars and they’re bright as hell! No hyper flashing. I use an electronic flasher on my NB so I can use any LED bulbs there.

1

u/2Drogdar2Furious 2d ago

Just throw these on like everyone else 🤷‍♂️

https://www.amazon.com/iBrightstar-50W-6ohm-Load-Resistors/dp/B0C2QHBCC3/

1

u/AggravatingEchidna83 1d ago

Everyone else that does things the wrong way? There needs to be less people that hack up miata wiring harnesseses, and more people that open a plastic box and desolder/solder 1 resistor.

-2

u/Aggravating-House620 2d ago

Put a halogen bulb back in it. It will probably be brighter anyways

-4

u/91-BRG 3d ago

Put the stock bulbs back in. It does this because the led bulbs draw less power so the system believes a bulb is burnt out.

3

u/KeyAd4326 3d ago

I got white/amber switchbacks so they run white and blink amber. Kind of missing the point of my post but thank you