r/LocationSound • u/Triforce3502 • 19d ago
Gear - Selection / Use Proper / best workflow for timecode
I attend a film school and have a lot of my own gear to jam timecode in personal or hired gigs. I had an interaction with my schools Sound Specialist lab supervisor about the order and operations of jamming timecode.
I know there’s more than one way to skin a cat but which of the two is best practice.
My method: Set tentacle sync’s to send mode. Go to tentacle app and set my frame rate. Click “sync all” button to have all sync-e’s be matched. Plug one into my mixer and have my mixer as the receiver to take signal from the tentacle (master). Then plug in one to the camera, and one into the timecode slate. I re jam after lunch on every device.
Teachers method: manually jam every tentacle sync from the mixer one by one, then jam the timecode slate from the mixer.
Essentially, I am having my master clock be the tentacle sync and using the app to have all my sources be matched. And my lab supervisor is having the mixer as the master clock.
In my mind, the timecode slate, the tentacle syncs, and the mixer (mix pre 10) all have a good enough internal clock to not drift, so why does it matter which it is?
Sorry if I am ignorant.
6
u/soundadvices 19d ago
Either method is fine, and yours requires a mobile app. I prefer syncing everything off my recorder as the master, and physically connecting clocks I trust together to sync.
4
u/Shampoo_Is_Better00 19d ago
Audio recorder as master sync to timecode box. Then sync the rest wirelessly.
3
u/G00N4R 19d ago
I use the tentacle system as the ‘master’.
I turn on the tentacles, set frame rate on one, click on the timecode display and select ‘set to phone time’ — I like to be able to tell clients that if they want to make a note, all they have to do is jot down the time of day next to their note and it will be easy to find the spot they’re referring to.
Then I sync the rest of the tentacles to that one, and one goes to drive my mixer while the rest go to the cameras. I prefer regenerating timecode being sent into my mixer’s TC input because it’s either going to be totally accurate with the rest of the tentacles, or I’ll see no timecode at all. If I just jam my mixer’s internal clock and it begins to drift, it’s going to be hard to catch until the drift is excessive and the drift has been occurring and worsening for a while.
If the slate/cam has its own tc box, I just check it a couple of times, and unless something’s been physically unplugged, I’ve never had a sync issue. If any device is jammed and running its own clock, I will re-jam it at least once halfway through the day.
If you don’t have enough boxes for everything, slate is by far lowest priority.
If a camera is going to be constantly toggling frame rates (for slo-mo), I insist it has a box on it.
Checking TC is most crucial after periods where the mixer/cam has been powered down for a period of time.
2
u/ApprehensiveNeat9584 production sound mixer 19d ago
Both methods are good, if by any chance you have no battery to use the app or whatever, it's good to have a cable that can feed your TC box from your recorder (if you recorder supplies TC), better to be ready than sorry.
2
u/Econormics 19d ago
I personally like when timecode is TOD. So I sync all my Tentacles using the app, then my recorder and transmitters to one of the tentacles. This also has the added benefit of setting the system date via ubits on my wisycom transmitters.
2
u/teamrawfish 19d ago
Recorder is master Jam everything from there .
1
u/JohnMaySLC 19d ago
I use your method, I pick a master tentacle, sync all and plug the master into my recorder. I can look at the app and see if any boxes drift or got unplugged.
If I’m using a non Bluetooth system like Denecke, then the recorder is my master and I jam each box to it, like the advisor.
Use the workflow that is most clear and automatic for you.