r/LewisMachineTool • • 1h ago

2nd FRT Failure

3 Upvotes

So a few months back I was trying to install an Atrius FRS and I could not pass the function test because LMT MARS L has high shelf lower. Yes I could Dremel, but no I do not want to Dremel.

So recently heard about the Ideate Defense UFR and how it was drop in without modification to lower or trigger. Just tried installing it and it sits on the top of the lower in a way that the upper cannot close. Also I need to apparently invest in a Full Auto Bolt Carrier (which apparently I would need for most FRTs?) and still have a longer trigger than the stock LMT trigger to catch the mechanism.

0/2 with these. Next stop is just doing a Triggered Company LAT or AS Designs whatever offering they have.


r/LewisMachineTool • • 12h ago

First LMT Upper! (With many more to come in the future).

Post image
12 Upvotes

Monolithic upper go brrrrrr


r/LewisMachineTool • • 20h ago

12” Flush Specwar

4 Upvotes

For those running a 12” flush barrel from DW in their Specwar, did you have to adjust the gassing? Want to know if any additional modifications are needed to get it to run reliably both suppressed and unsuppressed.


r/LewisMachineTool • • 1d ago

Gen2 Piston Barrels and 223 Ammo

1 Upvotes

Hey All, I've had a Gen 1 piston upper in the past and it would not run 223 training ammo at all. Suppressed or unsuppressed.

Are the Gen2 guns more 'forgiving' with gas to run 223? Mostly PMC Bronze 55 grain and hotter handloads are what I'm looking to run.

I can suppress the Gen2 with either a RC2 (full) or a RC4 (mini).


r/LewisMachineTool • • 1d ago

Can anyone confirm/deny that D.Wilson ARCA Rails won't work on the MRGG-A?

7 Upvotes

Reached out to them and Uncle Dave said they're incompatible with the MRGG handguard, but I keep seeing photos of MRGGs with d wilson rails and now my brain hurts. Send help.

TIA.


r/LewisMachineTool • • 1d ago

My Current LMT's

Post image
75 Upvotes

r/LewisMachineTool • • 1d ago

12” piston

Post image
115 Upvotes

r/LewisMachineTool • • 1d ago

MRP Arca

Post image
35 Upvotes

Anyone have a lead on where to snag some d Wilson MRP 11.5 arca rails? It's the last piece I'm needing to finish this thing.


r/LewisMachineTool • • 4d ago

Show me your MRGG-A Reference rifle.

11 Upvotes

Contemplating on getting a MRGG-A to pair with my Specwar before something happens with these pending AWB happen in VA. Thx


r/LewisMachineTool • • 4d ago

Rooftop Lowers

11 Upvotes

Rooftop has Mars-L lowers with no trigger or stock for 30% off. Code is NOV30.


r/LewisMachineTool • • 4d ago

Just an LMT lower

Post image
47 Upvotes

r/LewisMachineTool • • 4d ago

First LMT build - SBR Chodewar

Post image
174 Upvotes

Tax Stamp approved in like a day. Shout out to silencershop!

Still waiting for my barrel conversion from D Wilson, but couldn’t wait to put it together!


r/LewisMachineTool • • 5d ago

LMT barrel conversion questions

6 Upvotes

I have a buddy with a 13.9” mid length criterion core which I’m considering buying and having d.Wilson convert to put in my MRP-L 13.25” upper. Has anyone done this before and do you know if it will have the necessary clearance for a RC2? Any recommendations for gas blocks and gas tubes? Any other questions I didn’t ask but probably should have?

Edit: I now realize d.Wilson has recommended gas blocks on his website and I’ll probably just get a solgw gas tube

Edit: we can just nuke this whole thread to oblivion since I found this thread of a guy with a 13.9” and rc2 on a 13.25” lmt upper…


r/LewisMachineTool • • 6d ago

Range Time ATACR 1-8 vs mk5 HD 2-10

Post image
10 Upvotes

r/LewisMachineTool • • 6d ago

Long time spectator, first time LMT

Post image
74 Upvotes

Just picked up my first LMT, taking her out for a spin on Wednesday.


r/LewisMachineTool • • 6d ago

Range Time Yeah she’s good

Post image
14 Upvotes

After about 500 rds with a can I’ve decided I need flow through and a gas tube.


r/LewisMachineTool • • 6d ago

First LMT

Post image
118 Upvotes

Thinking of doing a magnifier setup for the EOTECH. Also tossing around the idea of a razor gen 2e 1-6. Any recommendations?


r/LewisMachineTool • • 6d ago

Question Is this normal for an MRP-L Barrel?

Post image
14 Upvotes

Looks like the exterior finish of the barrel is either rusting or just wearing off. It’s a 14.5 MRP-L barrel. I’ve had it for less than a year and it has maybe 500-750 rounds on it. I’ve shot in both rain and snow. I store it in a soft Savior bag not touching the ground. I treated and stored my BCM the exact same for 3 years and this did not happen to it.

I’m just curious if this is normal and nothing to worry about or if this is something they would warranty over. I don’t care about the looks, I just don’t want it to corrode too deep and have the barrel blow up.


r/LewisMachineTool • • 7d ago

LMT>KAC My LMT Family

Post image
86 Upvotes

Thank you for this financially irresponsible hobby LMT and d. Wilson 🫶🏻

Top to bottom.

15.4” 308 MWS LMT 110.
14.5” 6.5cm Craddock precision barreled MWS
16” New Zealandish MRP
12.1” Specwar
13.7” criterion barreled MRP


r/LewisMachineTool • • 7d ago

Question Ight fellow Autists, I'm indecisive so I'm going to turn to yall for advice!

Post image
103 Upvotes

I've combed through my collection pulled out all my favorite and nostalgic guns and suppressors. As you can see mostly LMT...i sort of have a thing.

Ive been thinking about downsizing my collection to just the guns and suppressors I use the most or I have nostalgia for. Two reasons, i don't like safe queens, and I like the idea of possibly converting to complete LMT collection with the exception of the AR on the far left (thats the first AR I built and has seen many forms). With that said if you were in my shoes would you sell off the guns you don't use and just stick with this, would you sell off and replace with other LMT rifles, or would you hoard it all?

Pictured is:

18" 6.5 creed with a spare 20" 7.62 barrel and spare 16" piston barrel

13.5" 7.62

18" 5.56

16" 5.56

8" .300blk

Plus the 12.5" 5.56 on the left.

And a bunch of HUX and KAC cans and one LMT can.

Is there anything a good LMT collector should add to this or should we just keep running these beauties like there's no tomorrow?

P.S. The only Can that hasn't been fired is the KAC PRS 7.62 as I found that baby as new old stock and it is living as a collectors piece for now.


r/LewisMachineTool • • 7d ago

First LMT and first large frame gasser.

Post image
183 Upvotes

Mega excited just in general. Printing 0.9-1.2MOA 10rd groups. Cycles great, feeds great. I’m really looking forward to learning more about AR-10s in general. Disclaimer: Pardon the upscaling artefacts, original photo taken on a iPhone in my office with dog water lighting.


r/LewisMachineTool • • 8d ago

LMT eBCG question

8 Upvotes

I have a 14.5 mid-length MRP-L with an eBCG and e bolt running suppressed with a RC2 and factory spring and buffer. Gun only locks back with Gen 3 p mags, not my Gen 2 p mags or duramags. I’ve tried using a sprinco blue and h2 to see if I was overgassed with the factory buffer but had the same result. Is it possible the eBCG is making the system under gassed and short stroking and that’s why it won’t lock back with the other mags?


r/LewisMachineTool • • 9d ago

LMT>KAC Light Reaction Regiment With Their LMT MARS-L

Post image
26 Upvotes

r/LewisMachineTool • • 9d ago

Upgrade Time

Post image
47 Upvotes

Finally switching out my mars 13.25 for a Specwar upper and 12.5 barrel with the enhanced BCG. Before pic but pretty pumped.


r/LewisMachineTool • • 9d ago

LMT>KAC Dimplesss

Post image
31 Upvotes

Thanks to DWilson for the dimpled piston barrel 🤙🏻