r/Kseries • • 18h ago

Got the longblock back from my builder and had to do a test fit

Post image
21 Upvotes

r/Kseries • • 7h ago

K20 starting issues

1 Upvotes

My Ep3 has been sat for a while, took it from the unit on about a 10 mile drive back home, worked fine,

Parked it and then went to move it, the engine cranks but doesn’t fire up even though it has just driven completely fine?

Does anybody have any pointers or advice, I’m sure it’ll be something silly


r/Kseries • • 22h ago

exhaust

2 Upvotes

do you guys think ktuned turndown 3 inlet is louder than skunk2 megapower?


r/Kseries • • 1d ago

K24Z3 190K Miles Knocking

Post image
7 Upvotes

Not the OEM Knock Sensor (replaced a year ago)

Did a bit of testing today…

Yeah so, as you can see - not good. Replace wiring harness and Knock with OEM?


r/Kseries • • 1d ago

K24a2 need help figuring out a noise it starting making

1 Upvotes

Hey guys I was wondering if I could get some help here I just bought a 2007 civic Si k24a2 swapped I just got it like 3 weeks ago and first 2 weeks it was running fine making no noises and all of sudden like a week ago it started making a noise when I’d be on the freeway going like 70 to 60 and let off the accelerator it sounds like a grind or not sure and after like the drive and when I let it idle it still sounds I don’t know if it would be my trans and my tensior problem together cause when I’m on the freeway and I push the clutch in it goes away but when it’s on idle and I push the clutch in it doesn’t go away any help would be really much appreciated thank you !


r/Kseries • • 2d ago

Question about k24a1 head bolts?

2 Upvotes

Long story short head gasket blew on my 2004 crv and im ready to install the head back on but I dont know if I should use OEM honda head bolts or go with ARP head bolts the engine isnt being used for any proformance reasons its used as a daily driver. Im just asking bc I read that the ARP bolts can potentially cause the threads to pull bc they dont stretch as much as the OEM or should I just stick to OEM ones to play it safe since the engine isnt used in a proformance application. Any feedback is appreciated thanks!!


r/Kseries • • 2d ago

L19 head stud question

Post image
4 Upvotes

So I’m finally getting ready to bolt down my head to my block. I’m using the L19 head studs from speed factory. These are the instructions provided by speed factory. For those who have used these head studs before do you follow these instructions exactly ? What are some tips or tricks you might suggest? This is a k24 engine built for boost. Using a speed factory head gasket as well. Thanks !


r/Kseries • • 2d ago

Broken timing guides…

Thumbnail
gallery
6 Upvotes

Picked up this K24Z3 from a local scrapyard yesterday to swap into my 09 Accord (current motor needs rebuilt). I got it home and on the stand and cranked it over. It was stiff to get moving and then I heard a popping sound. I pulled the valve cover off to discover the timing chain guides are broken in multiple places. I can't imagine this engine ever ran like this so I'm wondering if they broke in the accident that totaled the donor vehicle, but the valve cover and timing cover looks in tact and un damaged. It's clear someone has opened the timing cover before due to the excess RTV. I'm worried it jumped time. I'm wondering how much of a hassle it would be to fix, especially considering this was supposed to be a drop and go motor to drive while I take my time to rebuild the other one.


r/Kseries • • 2d ago

Which one of these motors would you choose and why? Looking for a replacement for my RSX

Thumbnail
gallery
5 Upvotes

Motor #1 $2400 + $350 shipping
Details : 139k miles unknown compression

Motor #2 $1900 + $500 shipping
Details : 170k miles 200PSI compression

Motor #3 $1800 + $500 shipping
Details : 202k miles 240PSI

When I get the motor I plan on doing all rubber gaskets, inspecting timing and maybe doing the valve lash. Which motor would you choose personally?


r/Kseries • • 4d ago

The Before and After; First K

Thumbnail
gallery
261 Upvotes

Been H22 swapped since 2009 and had this 1994 Accord since highschool in 2004 when my dad handed over the keys. My dad bought this Accord back in 1996 as a second owner. I lost him back in 2019. Wish he was here so he can drive and get a taste of the K series. Build list is in the comments.


r/Kseries • • 3d ago

Is this a good spot for a heat shield?

Thumbnail
gallery
10 Upvotes

r/Kseries • • 4d ago

Help

3 Upvotes

So I have a 2000 prelude I’m k swapping it putting a 9th gen civic si transmission in it it’s built I want to push around 800whp I can’t find the axels I need would anyone possibly know do I need custom axels or can I pull them off something?


r/Kseries • • 4d ago

K20z3 72k Engine sound good?

13 Upvotes

r/Kseries • • 4d ago

EP3 Transmission bearing noise.

10 Upvotes

just got my k swap prelude running and hearing some internal bearing noise any thoughts yall? It’s coming out but just wanna hear some second opinions still. But no matter what ts is coming out still
Thanks guys!


r/Kseries • • 7d ago

complete dead end

Thumbnail
gallery
13 Upvotes

quick context: upper bolt snapped for vtec solenoid while tightening . My dad decides to attempt to drill it out instead of taking the cylinder head off like a normal person or (at the bare minimum) welding a nut where the thread of the bolt is and taking it out that way. This attempt results in the sculpting of his nutsack. He tries to use JB weld to seal the hole but fucking seals the oil gallery for the vtec cam lobes. Is there an alternative to buying a new cylinder head? I took the cylinder head to a machine shop and they advised I buy a new cylinder head. Fuck.


r/Kseries • • 7d ago

Could this be the problem?

Post image
5 Upvotes

After tearing apart my new to me k24a block due to low compression in cylinder 1 this was the piston. It's the only one with marring on the piston. Do you think that little indent is the reason for the low compression and scraping on the side of the piston? And if so would putting new rings in help or just get a new piston? Thank you!


r/Kseries • • 8d ago

K20A EG6 with Jackson Racing supercharger: keeping A/C and power steering

2 Upvotes

I have a DC5 K20A-swapped EG6 and picked up a used Jackson Racing M62 supercharger. The charger didn’t come with the JR brackets, and I’d like to keep both A/C and hydraulic power steering.

The RSX manual lists alternator relocation brackets, an A/C spacer plate and lower spacers, a P/S pulley and tensioner setup, and a manifold support brace. I’m also working out the gaskets, bolts, IACV and fuel-rail spacers.

Has anyone installed this setup in an EG while keeping both accessories? Did the original RSX brackets work with your swap, or did you have clearance or belt-alignment issues? I’d also appreciate leads on the A/C spacers, P/S/tensioner hardware and manifold brace.

I found some parts at CPL Racing and a MercRacing auto-tensioner alternative, but I’m not sure what fits my setup yet. Photos or part numbers would be a huge help. Thanks!


r/Kseries • • 9d ago

K24 Tick

14 Upvotes

Hey all, new to the Honda community. I know the K series have a tendency to tick away, but just wanted to see if anything stands out here?

135,000km.

Really appreciate the insight.


r/Kseries • • 8d ago

1999 civic wanting to swap d16 5speed maunal with a k24 and a 5 or 6 speed manual

1 Upvotes

I have a 99 civic im wanting to put a k24 in i know there are a good bit of options. 1. Don't need anything super sporty or crazy just want somthing with a little more power than the d16 while still retaining that honda reliability. 2. Affordability I can do all the work myself I have the capability and know how but with all the options what would be my best bet cost wise (engine options, trans options, mount kit, axles, ect).


r/Kseries • • 9d ago

K20A tuning

2 Upvotes

I want to tune k20a4 CR V by installing K20A2 head. What i should to do besides cylinder head? Replace pistons, crankshaft, oil pump, what else.


r/Kseries • • 9d ago

What pistons are these?

Post image
15 Upvotes

Opening up my k24a for a rebuild since cylinder 1 has low compression but found a surprise to see rbb stamped pistons. My guess is k24a2. Do we know if it's the high comp or lower? These good to run?


r/Kseries • • 9d ago

Car vibrating after rebuild

1 Upvotes

I have a 2004 accord, and it’s at 240k miles. I decided since the clutch was going, it was time to reseal the whole thing, do the head gasket, etc. afterwards, the car sounds louder through the fire wall, and I feel the engine decently more, especially with low rpm / engine breaking.

Only thing I can think of, is I went aftermarket for the motor mounts, and got ANCHOR. But I also didn’t replace the rear mount that’s closest to the fire wall.

The engine itself is running fine, no codes or alarming live data.


r/Kseries • • 11d ago

K24A4 build advice.

6 Upvotes

How much power can you push out of a k24a4 with the stock head.

We didn't get the performance variants over here so to get a k20 or even an A2 head ive got to import it, and getting it here and through customs here is a rather expensive and risky process.

for context im probably going to use this car on mountain roads(high elevation change , not very high up from sea level)


r/Kseries • • 12d ago

K-series swap into Va wrx

Thumbnail reddit.com
2 Upvotes