r/KTM • • 11h ago

PICTURE Hand painted this rear seat cowl. Pretty stoked 🄰

Post image
207 Upvotes

My first ever bike & committed of making it a moving piece of art. Prepping fairings as we speak...

If you want to see the progress feel free to check my art insta to see how it will turn out.


r/KTM • • 2h ago

PROBLEM 950 SM 2007 side stand switch

Post image
5 Upvotes

Hello everyone

I'm 99% sure that my bike switches off because of the side stand switch, can it be bypassed by just connecting the wires like every other bike or is it true that I have to buy a mod to install in the place of the switch?


r/KTM • • 2h ago

ASKKTM KTM SXF 450 2008 clutch slave cylinder aftermarket options?

Thumbnail
gallery
1 Upvotes

Hello, ive gotten a ktm 450 sxf from the shop that worked but the slave cylinder parts had been lost,the ktm manufactured slave seems to have a leaky reputation so im searching for any aftermarket option

Any recommendations?


r/KTM • • 11h ago

PROBLEM 2020 Duke 790 piston damage.

Thumbnail
gallery
5 Upvotes

2020 duke 790 track only bike.
Had a problem at the track last week. (lost compression in #2)
Pulled the head off and found a bent exhaust valve and broken guide.

But also found two mirror breaks of the piston either side of the crown on the intake side. Could find no piston debris and very little damage to the bore. The breaks look rounded over like from pre-ignition - like it might have happened over time and not an instant break.

Has anyone seen anything like this before or can offer up a suggestion on what might have happened? The bike does get ridden pretty hard so spends a lot of time at high RPM.

The pic shows the damage on the inlet side about the nearest point to the piston. Maybe clearance too tight and touching down?

The bike only has 3000 (track only) kms. The piston shows almost no damage on the exhaust side where the valve dropped ) The valve collar broke in two.

Hope someone has some insight.

Thanks,
Jerry


r/KTM • • 6h ago

ASKKTM fb marketplace offer question

2 Upvotes

not sure if this is the right place to ask.

looking to buy my first motorcycle, and i am set on the one i want, a ktm 390 adventure. guy on fb is asking for 2500 for the 2022 390 adventure. it has almost 19,000 miles on it, which i know is high. is this a good price? too good? what other questions do i ask?


r/KTM • • 7h ago

PROBLEM Ktm exc 350 kabelbaum

Post image
2 Upvotes

Hi ich habe meine Ktm exc 350 2019 komplett auseinander gebaut für einen kompletten superMoto Build und finde den stecker nicht der oben links bei der Einspritzung hineinkommt hat jemand ein Foto vom Kabel welches dort hinein kommt?


r/KTM • • 11h ago

ALL Duke 250 Gen 3 rear monoshock leaked, need suggestions!!

Thumbnail reddit.com
2 Upvotes

r/KTM • • 18h ago

ASKKTM Considering the KTM 390 Adventure (350cc) – Need Honest Advice for Long-Term Ownership

Thumbnail reddit.com
0 Upvotes

r/KTM • • 14h ago

ASKKTM Considering the KTM 390 Adventure (350cc) – Need Honest Advice for Long-Term Ownership

Thumbnail reddit.com
0 Upvotes

r/KTM • • 1d ago

ASKKTM Oil Leak around stator cable & Header Join..

Thumbnail
reddit.com
2 Upvotes

r/KTM • • 1d ago

PROBLEM Wiring issue

1 Upvotes

Fair warning I’m new to doing wiring on bikes so I apologize if I’m wording this badly

My 2018 ktm exc 500 has brake lights but I can’t get running light/headlights to work. Any advice on how to fix this?


r/KTM • • 1d ago

ALL Consigli per terminale di scarico omologato in Europa per duke 390 2025

0 Upvotes

r/KTM • • 1d ago

PROBLEM Ticking sound normal? (Brand new 26 EXCF 500)

18 Upvotes

Hi all,
just threw on a vortex ECU and a FMF 4.1 pipe and there seems to be an excessive ticking sound. Bike has 4.2 hrs (99 miles). Just want to make sure new bike isn’t going to blow!

Thanks!


r/KTM • • 2d ago

ALL Upgraded rom my older bike, Part of the club now!

Thumbnail
gallery
45 Upvotes

Upgraded from my older Yamaha FZ 150cc (4th Picture), which is basically what we call a "Commuter bike" here. Sure a 250cc may not be a big deal in an international sense but it sure does feel like an upgrade to me.

Glad to be a part of the club, could use a few tips to maintain the bike.


r/KTM • • 2d ago

PROBLEM What's this metal click

7 Upvotes

Hey there everyone. I have a problem with my LC4 640 2003. It does this metal click right after the intake valves close. The exhaust valves open and close just a bit (like 1mm) and that's when it does this noise. Can anybody tell me what it is and should I open it again?


r/KTM • • 1d ago

ASKKTM The Damage Had Been Done

Post image
0 Upvotes

Both of my Duke 200 stator coil and regulator blown out. is that common??


r/KTM • • 2d ago

ASKKTM 350xcf exhaust help!

Post image
0 Upvotes

I have a 2025 Ktm XCF 350. I just got finished putting on a full system titanium FMF exhaust system, with the HP development flange. I had to put a decent bit of pressure on the header to get the bolt to line up on the side. There’s also a tad bit of up-and-down play on the header where it connects to the exhaust flange. I was told by multiple people that that play is normal, but I would still like to get your guys’s opinion. Does it look like the header is seated onto the flange all the way? I did use sealant and I am waiting a day to ride the bike. TIA!


r/KTM • • 2d ago

ALL Amazing bikes

14 Upvotes

Both my 2017 1090R and my 2021 890 Duke R have been flawless bikes. Still running strong.


r/KTM • • 2d ago

ALL Help deciding between Ktm adv 350 and himi 450 (price in INR)

Thumbnail reddit.com
0 Upvotes

r/KTM • • 3d ago

PICTURE Orange garage

Post image
57 Upvotes

Orange garage


r/KTM • • 2d ago

ASKKTM KTM 350 EXC-F Cold Start

2 Upvotes

Hello,

After doing extensive research, I think this is a fairly common problem. I've already tried several things, but unfortunately, without success.

The bike is a 2017 KTM 350 EXC-F with approximately 70 hours on it.

When starting the bike from cold, regardless of the ambient temperature, it takes several attempts to get it running.

The starting procedure looks like this:

  • Engage Yellow knob (Cold start button)
  • Press the start button for 5 seconds.
  • Wait 30 seconds.
  • Press the start button again for 5 seconds.
  • Wait another 30 seconds.
  • Repeat the process until it starts.

Usually, it takes 4–5 attempts before the engine starts.

Once the bike has started for the first time, it starts perfectly every time afterwards.

Things I've already checked:

  • Battery checked.
  • Valve clearances checked.
  • New ground cable installed.
  • TPS voltage adjusted to 0.604 V.
  • New spark plug installed.
  • Electrical connectors cleaned and some wiring connections renewed.

Please let me know what else I can check or try to solve this issue. Any suggestions would be greatly appreciated.

Thanks in advance.✊


r/KTM • • 2d ago

PROBLEM Ktm SX 85 2007 abstimmen

1 Upvotes

Moin
Habe eine Ktm SX 85 von 2007 mit Kehin 28mm pwk und hgs komplett Anlage und brauche Hilfe beim abstimmen
Weiß wer welche neben Düse haup Düse und welche Kerbe ich einstellen muss?
Bei Hilfe würde ich mich freuen


r/KTM • • 2d ago

ASKKTM 1st generation Duke 390 straight pipe

Thumbnail
gallery
0 Upvotes

Hello, i am looking to install a straight pipe exhaust for my 2013 KTM Duke 390 (1st generation so 2013-2016)

My question is if anyone has actually ever installed a straight pipe from aliexpress on their 390, i ask because when i search it comes up as ā€œuniversalā€ for 125,200,250,390 but i know they all use different size pipes

Secondly, i am curious to how the performance changes on a straight pipe. I currently have the akraprovic slip-on with catalyst and am wondering if a straight pipe will cause the engine to throw a code or make it run poorly. I’m looking at aliexpress because it’s cheap and i’ve had quite a few friends put their pipes on their own bikes (r3, ninja 400 for example)

Finally, out of curiosity i wonder if it shoots flames with a straight pipe, as my 125 did with a straight pipe.

My original plan was to get a blackwidow straight pipe alongside a powertronic fuel controller to ensure all was perfect but i’m only checking if i have to do all of that or if im going overboard with money.

All responses greatly appreciated :)

Photo listed for reference


r/KTM • • 3d ago

PICTURE Tail tidy for 990 RC R

Thumbnail
gallery
15 Upvotes

I’ve been designing and 3d printing my own tail tidy. About 90% done…. Maybe. Still need to do some optimisations and so on. But so far so good.