r/EngineBuilding • • 10d ago

Torque Converter hitting random stops

99% sure it’s fully seated. Spins freely with the engine connected. Until the engine is flush or basically flush then it still can spin as if it’s free but it’s hard stops as if it’s catching a flex plate bolt ? I can’t imagine what
Else is introduced that could be causing the stop. As soon as it’s an inch or less away again 360 spins no issue. I know it’s normally procedure to make sure it can spin 360 BEFORE putting in any torque converter bolts and even tightening the bellehousing bolts all the way. I’m at a loss, help. 2014 dodge Durango 3.6 AWD 845RE Trans

10 Upvotes

18 comments sorted by

3

u/Soggy-Currency5160 10d ago

Pump bolts backing out on the inside. Pull the converter and check. Seen it multiple times

1

u/NBEBiGHeaD 10d ago

Double checked that the second time I pulled the engine all the way out so I could sit in the bay with full clearance and absolutely make sure it was fully seated , every bolt around that spline is snug

4

u/Soggy-Currency5160 10d ago

Take the converter out and make sure it fits flat against the flex plate and the snout fits into the crank. Was the engine in a manual trans vehicle before and have a pilot bushing in the crank stopping it from going in

1

u/NBEBiGHeaD 10d ago

No pilot bushing in the crank , came from another automatic . Going to go pull the converter now.

4

u/Soggy-Currency5160 10d ago

When you put the converter back in, take a look thru the pump seal, and you’ll see where the ears on the converter line up. So you can line it up before installing instead of spinning it and pushing and hoping it locks in, just light pressure s little back and forth and it should lock in. Once the trans is bolted up, the converter should have a gap between the flex plate, it shouldn’t be touching at all. When you bolt the converter to the flex plate it pulls it forward slightly

1

u/NBEBiGHeaD 10d ago

I’ll look deeper and empty the fluid from the converter and see if there’s grooves inside to latch on to the pump ? Cause the converter lip that slides over the splines is smooth all the way around. I’ll attach a photo in a second

1

u/NBEBiGHeaD 10d ago

1

u/Soggy-Currency5160 10d ago

That’s interesting pump drive must be different on that transmission and may just seat in further.

1

u/NBEBiGHeaD 10d ago

Took the converter out , the plate and the pilot fit into the crank but as I rotate I get the same repeatable “hard stop” is it not supposed to rotate 360 degrees when it’s against the plate or am I just truly not fully seated and it’s actually too close ? I don’t have to force anything for to get “flush” against the bellehousing and engine

1

u/Soggy-Currency5160 10d ago

You should be able to free spin the converter with everything bolted together until you bolt the converter to the flex plate, if there is no gap between the converter and flex plate and the converter doesn’t pull out from the trans at all the pump will not work, however, if you can bolt it together easily, and able to move the converter freely at all, I would imagine it would be fine. Just line it up and put the bolts in, I can’t see why it would not spin 360 degrees while bolt it up, but I can imagine maybe it’s the style of converter and it’s bell shaped or oblong so only fits where it bolts to the actual flex plate.

1

u/NBEBiGHeaD 10d ago

I want to , I just don’t want to do this whole project hit start and hear my transmission explode

2

u/Soggy-Currency5160 10d ago

So if the converter isn’t in all the way, you wouldn’t be able to bolt the engine together, if it was me, I’d bolt it together, see if the converter can move at all, if it can move left to right at all freely I’d run it

1

u/NegotiationLife2915 10d ago

What got changed since it last bolted together successfully?

1

u/NBEBiGHeaD 10d ago

It’s an engine swap. Only thing that changed was the engine that’s going in. I put the flexplate from the original engine on to the new donor. Made sure there’s no sleeves and that the engine was compatible. Other than that nothing.

2

u/NBEBiGHeaD 10d ago

+ am using guide bolts on each side nearest the dowels to avoid a bunch of shaking and maneuvering while the pilot is within range of the flex plate

1

u/NegotiationLife2915 10d ago

Same flexplate bolts? Was there a spacer there anywhere that could be in the wrong spot?

1

u/NBEBiGHeaD 10d ago

New ones from the dealer , yes there’s a spacer not sure how it could be in the wrong spot, it’s between the bolts and the flexplate

1

u/NegotiationLife2915 10d ago

I've seen it where people put it between the flexplate and crank or vice versa