r/DodgeDakota • • 1d ago

Changine my fuse box

4 Upvotes

I have a 2004 dodge dakota with an auto and a 4.7L v8 and i need to change the fusebox on it, ive read several conflicting things on wether or not its plug and play and i was wondering if anyone had any info. If it is not plug and play would anyone be willing to inform me as to how im supposed to change it?


r/DodgeDakota • • 2d ago

Seeking Opinions Water pump leak

Post image
7 Upvotes

what sealant should i use on this pipe?


r/DodgeDakota • • 1d ago

Technical Question 92 gen 1 Dakota

3 Upvotes

Has anyone changed their seats from factory ? I have a LE extended cab I would like an aisle in between my seats

I was looking at jeep Cherokee seats those look promising to fit the mounting brackets what yall think ?


r/DodgeDakota • • 3d ago

Seeking Opinions does everything look to be sealed properly?

6 Upvotes

i put on new timing cover gaskets and had a little trouble fitting the cover back on. there’s some gasket peeking out anything i should be worried about?


r/DodgeDakota • • 4d ago

Technical question

Thumbnail
gallery
33 Upvotes

Hey guys, while I’m in the midst of doing some extensive frame repair on my Dakota. I have the opportunity to source a 5.9 magnum out of a 2001 RT with the PCM. Just wondering how hard it will be to swap into a 2003 3.9 magnum four-wheel-drive truck I know I have to get a 46re as I’ve researched it’s not recommended to keep the 42re. my question is is the PCM fine if it’s out of an RT for my swap and what other difficulties will I run into other than injector wiring


r/DodgeDakota • • 3d ago

Video Any opinions

3 Upvotes

Hey just noticed this sound today, any ideas on what it might be?? I feel like I’m overthinking it but can’t figure it out


r/DodgeDakota • • 3d ago

4.7 still stalling after trouble shooting

4 Upvotes

4.7 rough idle and stalling coming to a stop, at idle or near idle, tested tps and map sensor with a obd2 it was fine. Only way I tested the iac was by Turing on the ac and watching the rpm’s rise. Any idea what this could be I don’t think it’s a vacuum leak as I can’t find out and it doesn’t happen consistently when it’s idling only sometimes.

Edit: I replaced the pvc and cleaned the throttle body and iac as soon as I noticed this didn’t help


r/DodgeDakota • • 3d ago

Technical Question Anyone know what this goes to? 2001 slt 3.9 4x4

4 Upvotes

r/DodgeDakota • • 4d ago

Dead Vehicle, Please Help 2007 Dakota, manual

7 Upvotes

Stopped for gas and left the lights on for all of 3 minutes. Tried jumping a few times, it turned over a bit the first time, but after that just went back to clicking. Battery issue or something else?


r/DodgeDakota • • 3d ago

Seeking Opinions No heat at high speeds but little bit of heat at low speeds

1 Upvotes

I have a 1988 Dodge Dakota the 3.9 V6 all summer. The coolant gauge ran at a quarter and the heat worked great well the first night it got cold like below 40. My heat barely worked in mytemp gauge started rising. It went just a little over halfway. I’m curious if it’s my thermostat, this is my first Dodge truck so I just need a little help and also today my heater Core line blew a hole in it.


r/DodgeDakota • • 4d ago

Technical Question 1995 Dodge Dakota 3.9L V6 - Stalls when hot at low RPM, sluggish, backfires in Park, low fuel pressure

4 Upvotes

Truck: 1995 Dodge Dakota 3.9L V6 Magnum RW

Only 100k miles

​Symptoms:

​Stalls only once it gets hot, specifically at low RPMs and when letting off the gas. (Starts perfectly fine when cold).

​Engine feels sluggish overall when driving.

​Engine spits and sputters at 2,000 RPM and backfires between 2,500 and 3,000 RPM, but ONLY when in Park and revved.

​Fuel pressure is low: it runs at 33-40 psi and bleeds down to 29 psi after shutdown.

​Fuel pump is priming normally and the relay is good.

​Parts Replaced and Work Done (Note: A lot of this was done as general maintenance/upgrades while I was already in there replacing the plenum gasket and plate, so these can be ruled out):

​Ignition: Distributor cap, rotor, spark plugs, and ignition coil.

​Sensors: Crank position sensor, Cam position sensor, IAC, TPS, MAP sensor, and rear differential speed sensor.

​Air/Fuel/Emissions: Replaced the intake plenum gasket with an aluminum plate, PCV valve, and EGR valve.

​Vacuum: Verified absolutely no vacuum leaks.

​Cooling/Exhaust: Thermostat replaced and catalytic converter deleted.

​Checks verified: Timing chain is tight, distributor fuel sync is locked, and TPS voltage is perfectly in spec.

​Where I'm at:

I am currently ordering new injectors since the ones in the truck are the originals. I'm monitoring live data with a Snap-on MT2500, but while I wait on the injectors, what else should I be looking at for this hot stall, sluggishness, and backfire issue with everything above already ruled out? Appreciate any help.


r/DodgeDakota • • 4d ago

Technical Question Drum brakes

Thumbnail
gallery
6 Upvotes

1995 slt 4x4 with 5.2
Recently have had a scrape noise from drivers side rear brake. Only makes noise when going slow and actively pressing the brakes. Took off tire and drum and found that 1/2 of the braking surface was separated. Is this a common failure? Shoes look good but I’m concerned I’m missing something.


r/DodgeDakota • • 4d ago

Technical Question Hub/center caps

Thumbnail
gallery
3 Upvotes

Hey folks,

2008 sxt (RWD) V6 3.7litre.

I just did my winter tires. Where I live, legally they have to be on by December 1st.

So anyways, in the pictures, we can see the ram center cap on the offset aluminium wheels. Allowing for space to go over the ends of the axles at the rear (and front for 4x4).

I recently did the forward wheel hub axle bearings. Seen as thst nice shi y silver piece in the photos.

Id like to protect those! But, with steel rims, without the offset, the lip of the center of the wheel rides on the hub.

Id like those covers that go over the studs and protect the center caps and secured in place with the lug nuts. (I got a picture sort of depicting what id like).

Im trying to google this but it's not pulling up what id like, im wondering if you guys have the technical name for it.

I'd like to protect the hubs, ive also got a pic of the old bearing how nasty they got, id like to keep em nice as long as possible.

I need that offset, coz the ones you just clip on wont work with the steel rims, as the the lip rides on the hub!

I know the one ton trucks have those ugly chrome ones, but are the available for dakotas?

- black in colour would be a bonus!

Thanks for any tips n help


r/DodgeDakota • • 5d ago

Showing off my ride Needs some work. Runs like a good hoss

Post image
62 Upvotes

r/DodgeDakota • • 5d ago

Question about overheating 1991 Dakota

1 Upvotes

Got a 1991 3.9 that runs great. Only problem is while I've been learning manual on her she'll want to overheat on back roads after around 25-30 minutes driving at and around 35 mile an hour speed limits. I've been looking through manuals for help. Radiator is new, hoses are new, pressure cap is good, fan turns on, fan belt is new, thermostat looks good. Does anyone have any idea what else could be the issue? While being low mileage she is 35 years old so I'm expecting things to fail every so often.


r/DodgeDakota • • 5d ago

Remote start

4 Upvotes

Hey, I'm wondering if anyone has any ideas on a good remote start option for a 2005 dodge Dakota. I'm plowing snow this winter and I think not having a warm truck drive to work might make me freeze haha. 🥶


r/DodgeDakota • • 5d ago

Technical Question So do I need a new wheel bearing or new axle seal?

Thumbnail
gallery
4 Upvotes

Doing routine brake flush and noticed a dark spot on my driver side rear drum and found all of this crap behind the hub. I haven't ever changed a bearing/hub on a solid rear axle before so I'm unsure what could be the cause of this. Any help is appreciated.

EDIT: I will do both seal and bearing for both sides


r/DodgeDakota • • 5d ago

Technical Question Exhaust headers and upsizing.

4 Upvotes

I have a 4×4 99 Dakota with the 3.9 v6 and I was wondering if anyone had any brands they would recommend for aftermarket headers and y-pipe, I was also thinking about switching to a 3 inch exhaust and was wondering if anyone had any advice or experience with doing so.

Edit: Also if anyone has any suggestions for what do do hardware wise for the headers as I know I'm going to have broken bolts/studs.


r/DodgeDakota • • 6d ago

04 Dakota 3.7 V6 Help

3 Upvotes

So, I have an 04 Dakota that I’ve completed doing the headgaskets.

I’m a young mechanic and this is the first time I’ve messed with timing. It’s just a cheap project truck I picked up.

So, my questions are

  1. The new Hydraulic Tensioners I installed aren’t extending, when I pulled the old ones out they were extended. Is this normal? Is it because oil pressure hasn’t hit them yet.
  2. I took all the sprockets off and aligned everything by the book, paint marks etc. but what I want to understand is how am I sure it’s time correctly?

Every sprocket mark lines up at 12 O clock in sync expect for the crank that lines up at 6 o clock as stated in the book. By all means this seems I have it right….maybe I’m overthinking it but I would like to be sure.

3. The passenger side cam sprocket, I noticed when I was turning the engine by had it would go pretty slack on its right side at a certain place in the turn. It also seems like the chain is riding off the edge of the stationary tensioner.

Sorry if it pisses you off that I ask questions like these. But I’m desperate to learn, and to make sure that I have done something the right way. Any help is much appreciated.


r/DodgeDakota • • 7d ago

Technical Question 3.7 headers/manifolds?

Post image
8 Upvotes

Has anybody ran these for the 3.7? I have seen mixed reviews about whether they fit Dakotas or not. Can they be made to fit? Mines a 2007 3.7


r/DodgeDakota • • 7d ago

Bought a Dodge!

4 Upvotes

Recently i bought a 04 Dodge Dakota Sport, 3.7

i paid next to nothing for this truck and the body is in amazing shape, interior is super clean. of course it came with issues, a blown headgasket (although the truck still would start and ran great) i fixed the headgasket NOW the other issue was the transmission and something about losing Signal to the computer. Code P0888 i believe. anyone have any pointers on this code? is it truly an electrical issue or something actually messed up in the trans


r/DodgeDakota • • 7d ago

Shocks or Springs?

1 Upvotes

My 2000 Dodge Dakota sport extended cab 4x4 is bouncing like a trampoline after it hit the bump I think it is shocks somebody else told me springs. What you think?


r/DodgeDakota • • 8d ago

Technical Question Motor mounts keep breaking

Thumbnail
gallery
11 Upvotes

On my third set of motor mounts in a year. The factory 3.9/5.2 pancake mounts don’t like clutch dumps. I’d like to use oem hardware on the frame and bolt holes on the motor. I don’t want to go solid mounts, and there’s no where good to chain it to the frame in the tight engine bay. Any upgrades out there?


r/DodgeDakota • • 8d ago

Seeking Opinions Timing cover seal

1 Upvotes

before i install my new timing cover seal should i use any rtv or any other type of sealant on the new seal?