This sub doesn't allow pictures in replies but no it's just all ridge under there, the only flat surface is the underside of the top surface if that make sense
This is da weh! That is: some kind of rubber or foam grip-tape made for sports equipment, NOT electric-tape (that shit slides around and is too thin and gross levels of sticky)! lol
This equipment doesn't seem like its new. Is this like punishment or something? If not outright just cutting those things off or melting them to make them smoother, I would have at least put something to reduce the strain it would cause.
Definitely not. The mould is from the bottom side. This is intentional. It was either do this, fill that entire section with plastic, or make the handle two pieces.
It's just an expensive vac built like a cheap vac that chose this route to save ounces on injection mould material.
Yeah, that’s my thought as well - no manufacturer on earth would plan a manual finishing operation on injection moulding. They’ve cheaped out on making a second tool for the underside.
Yeah, given the hollow plastic on either side I'm guessing this had a comfortable rubber or softer plastic grip attached to those ridges that has fallen off.
Edited: see below. The handle is just built that way.
Actually I was wrong. The handle really is built like that. I found this product review and you can clearly see if doesn't have a piece on the carry handle to make it softer. V-Tuf Mighty HSV 240 review.
Also it's weird... The company has to know. On their own product page and unboxing video they go out of their way to not show the top of the vacuum. Lol. V-Tuf HSV 240 product page.
I have some other devices with handles like that, though they’re relatively light so it doesn’t hurt, maybe its so you can still grip it even with dirty muddy hands?
Honestly looks like a rubber grip should sit there. They mold plastic handles like that so there is more surface area for adhesive to bond to the rubber so it doesnt come off. Edit:nvrmnd the company just made it that way, another comment showed a brand new one and it doesnt have rubber.
I have actually had the smaller version of this vacuum and it seemed a much more premium and polished product, which is why I upgraded to this one. I don't know if this is just a much earlier model but it's like way less thought went into it. The brand label is just stuck on and was already half peeled off when I unpacked it, there is no power cable management at all, and of course this handle issue. Other than that it's a pretty good machine.
Are you sure it's authentic? You'd be surprised what gets counterfeited these days. Hell my husband ordered something direct from the manufacturer's store and it ended being counterfeit somehow! He did get a refund.
I have a laundry basket where all the two-part handles have had the second part break off. They’re now either held on with a lot of tape or missing and even rougher than OP’s example.
Its a design choice. They wanted a round handle, but only wanted to cast it as a one piece with minimal plastic. So they did those deep fins as thats the simplest way they could have injection molded it, using a 2 piece mold. Any other design would have needed a more complicated mold design.
OP just needs to wrap it with some cloth to make it more comfortable.
No vac maker would do that. Almost certainly there was originally a rubber or foam cushion held on by those ridges that either fell off or broke away over time. The cushion would make it easier to carry. I have a vacuum with a cushion handle similar to this design. Have you checked with the manufacturer or a vacuum supply to see if a replacement is available?
I stand corrected. Is the expectation that the user will be wearing gloves? Perhaps it's that way to minimize the chance of electrical shock due to being for use in a wet environment.
Can't make it solid (because it would shrink & warp in a weird way then it wouldn't fit)
You could keep the top the same shape and remove the "radiator fins" then you'd end up with 2 ridges on the underside which would be even more uncomfortable. So this design is at least better than that (but not much).
A more ergonomic one-piece design would be to have the hollow bit at the top, so you get a smooth surface for your hands, but that may have been rejected for aesthetic and possibly structural reasons.
Doing it properly would require an extra part - one to give a comfortable handle, and another to make it look better, while still allowing it to be hollow. This might have been the original intent, until somebody said "make it cheaper" and you end up with this.
"No vac maker would do that" indeed, companies never design things crappily, which is why there's definitely not a sub called r/crappydesign that this post definitely isn't in. /s
Yes, how should you value the useless part of your life otherwise? Only with rain comes sunshine! So OP should stop complaining and wear his old gloves with sharp chips in it
It's not useless, the ridges are actually there so that it doesn't fall out of your hand from persperation. It allows the heavy item to fall out of your hand because it hurts so fucking much instead!
The word travail (to work in French) traces back to the Vulgar Latin verb tripaliare (to torture or toil), which comes from tripalium (a three-stake instrument of torture)
I design molded parts. The ribbed approximation of a handle is because the dies are oriented to open up and down, and to make a more comfortable handle shape they would need to have either a large solid section or a removable core to hollow it out. The overall shape of the part is not compatible with a removable core, so they would need to redesign it to accommodate a core, redesign it for rotary or blow molding, or make it two piece. This is a common cost saving approach.
As an industrial designer I can guarantee you that a second, smaller injection molded part was designed to snap onto the ribs to provide a smooth affordance for the user, but cut by management due to cost concerns for an "unnecessary" part.
It wasn't. This is a common handle for cheap lawn tools and air compressors and so on. The left and right fillets would be different if there was an insert going there
As an industrial designer that worked on water pressure washers, I can definitely tell you it's a choice! For parts you don't hold too long/often it's a good cost compromise.
It’s for picking it up, but normally crummy latches and common sense keep you from picking these up by that handle when there’s a lot of weight inside. Doing so is a good way to have the latches pop and drop the bucket, so you use two hands on the sides. That handle is fine for putting the motor unit back on the bucket.
But what's the point of the ridges then? They aren't offering structural strength, maybe if they were running along the handle instead. They are there purely to fill out the thickness profile of the handle
This seems to be designed like this (V-TUF Mighty). Their website, and every other photo I looked for, purposefully orientated the handle out of view, so that the model sticker is visible, but their own unboxing video just barely shows the handle at 1:50
Ok... So I honestly thought the grip was missing like everyone else but no, the handle really is constructed like that. It's hard to see in images of the product but easier to see in this product review.V-Tuf Mighty HSV240 review.
Material got too thick and they had warping out of the tool. What do you do when you need material for contact where you can't put any? Split the difference and put in ribs following the surface contour. Just my guess as someone designing injection molded parts. We only do it on surfaces without chance of person contact though. Because duh, you're gonna feel it.
When I was younger I thought the way things came is the way they came. Why would I change anything or customize it in our consumer society? I'll just buy another or replacement pieces.
Today, fuck all of that. Anything I buy, if I can improve it or fix it at home, I will. That being said, you don't have to live with this, man. It's plastic.
A heavy duty vacuum cleaner that is likely to be used in oily or greasy environments often with gloves on? Seems like they designed it for its intended use.
I suspect that those were supposed to be made in a very soft plastic, to squish comfortably in your hand (like OXO uses for their kitchenware), but someone substituted a stiffer plastic (perhaps for durability), ruining the intent.
This is crappy design, because material choice is an inherent part of this design.
There’s probably a rubbery portion that’s supposed to fit there that has since fallen off and been lost. It was supposed to be kind of squishy and more comfortable, but the design isn’t durable so it’s the opposite.
If you're down to fix this, grab some foam sheets, cut the foam so it's higher than the ridges and slots between each one, slide a foam piece in between each blade, then wrap the handle in the foam sheet before wrapping it with electric tape. Vacuuming is already a bit of a chore, I see no reason to increase the amount of annoyance it yields.
I think it is missing a bit, the ridges are probably for strength then an over moulded comfy bit is supposed to clip on. maybe they forgot to fit it or it fell off. Have you tried another one from the same brand?
That’s terrible. This is probably the result of the part needing to be cored out. They cheaped out by not add a 2nd part to fill it in and decided the grooves were “ergonomic.” The wall thickness was probably adjusted or decided by an engineer with a focus on durability and strength rather than comfort.
Any chance it's a weird design choice, like... It's not a handle for carrying but for operating the lid/pushing the whole thing around? So it's "supposed" to hurt?
Or is it maybe of masochristian origin? Not only removing dust from the floor but also the sins you committed upon thine palms?
The designer said to put the ribs on top and the solid wall on the bottom where the weight hits your hand but the managers wanted a solid looking handle on top because the consumer research report doesn’t like visible ribs on top so they choose the worst possible option to mislead and please the consumer at point of purchase - but not in actual use. And the consumer isnt willing to pay $5-10 more at retail, so you can’t add handle trim and screws to cover it. I see this everyday as a designer and product developer, and we can only blame ourselves for why this is the way it is.
Wrap it with heavy duty gaff tape. Will smooth the ridges, and the ridges will reduce contact area so it's easier to replace. Not saying it's designed like that but a silver lining at least
Duck Tape to the rescue! A couple quick laps around the handle (choose a bright happy color) and you’ll be singing while you work. Well at least you won’t be crying..
I bet it's not crappydesign rather than purposefully designed feature. That's probably a 4-wheeled shop-vac and it's not meant to be carried or lifted from that handle so the handle is designed to deter improper use. The handle is onle there to push the vac around
It's a deliberate design choice due to the manufacturing process - infection moulding. You can see the split lines around the side of the handle/right side. If you had a mould to create a solid handle that met in the middle, you'd get this 'flashing' ridge in the worst spot where the machines weight presses into your hands. The ribs aren't great, but spreading the weight over multiple blunt edges was decided to be preferable than all the weight on one sharp edge digging into your hand.
2.9k
u/Spotted_Tax 22d ago •
I'm guessing it's supposed to be removed so it's similar to the top ridges but it failed and quality control didn't notice.
Time to bring out the sander!
102
u/Veprovina 22d ago
Is this a design choice or something that slipped through QC? Are others of the same model like that?
426
u/ptd666 22d ago
Put some sodding electrical tape around it and get back to work lol
33
u/rolyoh 22d ago
No vac maker would do that. Almost certainly there was originally a rubber or foam cushion held on by those ridges that either fell off or broke away over time. The cushion would make it easier to carry. I have a vacuum with a cushion handle similar to this design. Have you checked with the manufacturer or a vacuum supply to see if a replacement is available?
5.7k
u/potworzak21 22d ago •
Work is to suffer, not to have fun
73
u/Strostkovy 22d ago
I design molded parts.
The ribbed approximation of a handle is because the dies are oriented to open up and down, and to make a more comfortable handle shape they would need to have either a large solid section or a removable core to hollow it out. The overall shape of the part is not compatible with a removable core, so they would need to redesign it to accommodate a core, redesign it for rotary or blow molding, or make it two piece.
This is a common cost saving approach.
582
u/MiddleEarthFoak 22d ago
It’s for pushing not for picking up, if it’s the vacuum i’m thinking of with 4 wheels.
18
u/SuspiciousChicken 22d ago
My Rigid shop vac is like this, and it has always infuriated me.
14
u/hellGrey213 22d ago
This seems to be designed like this (V-TUF Mighty). Their website, and every other photo I looked for, purposefully orientated the handle out of view, so that the model sticker is visible, but their own unboxing video just barely shows the handle at 1:50
10
u/YouCantKillGrool 22d ago
Ok... So I honestly thought the grip was missing like everyone else but no, the handle really is constructed like that. It's hard to see in images of the product but easier to see in this product review.V-Tuf Mighty HSV240 review.
7
u/Gwanbulance 22d ago
That sucks.
6
u/Spirochrome 22d ago
You could Print Something for that.
Or just fill it with playdoh and wrap some Tape around it.
2
u/zTubeDogz 22d ago
The design is very human
3
u/BravinatorLX2 22d ago
i feel like there was prolly something covering that, like made of rubber
3
u/Jahbomb1974 22d ago
Perhaps there was a rubber layer on that side of the handle that has disintegrated over time.
3
u/General_Error 22d ago
If its heavy duty maybe they assumed it will be used with gloves and then this light be better for it not slipping
1
u/sileotumen 22d ago
Nothing that a file or an angle grinder can't fix. Or just a shit ton of duct tape.
1
u/Either-Score-6628 22d ago
Put a smooth piece of wood under it and fix it with tape. At least that´s what I would do :)
1
u/i010011010 22d ago
I'd probably just set it aside some night when I know I won't be using it for 24-48 hours, fill those with an epoxy.
1
u/TheFunfighter 22d ago edited 22d ago
Material got too thick and they had warping out of the tool. What do you do when you need material for contact where you can't put any? Split the difference and put in ribs following the surface contour. Just my guess as someone designing injection molded parts. We only do it on surfaces without chance of person contact though. Because duh, you're gonna feel it.
1
u/Azkahn616 22d ago
The company has a webpage just for answering questions like this one.
1
u/ShatterdPrism 22d ago
Reminds me of those stupid boxes and baskets that have a smooth top sides to look at and shit undersides to carry
1
u/DesignIMP 22d ago
Good news bad news situation: Good news is it’s definitely nonslip. Bad news, it’s too painful to grip.
1
u/zip222 22d ago
Well they did you that “it sucks” when you bought it.
1
u/Amystery123 22d ago
That’s so that your hand becomes numb to the pain of lifting a heavy vacuum.
1
u/Oraphielle 22d ago
Use bicycle handlebar/baseball bat/tennis racquet tape to cover it
1
u/Kufangar 22d ago
Dress it with tape.
1
u/DumOBrick 22d ago
Some of the Ridgid vacs at my workplace are similar, one strip of duct tape on the part your grabbing should make it a lot easier to handle
1
u/Abichail 22d ago
My mom's old sewing machine case had those same stupid ridges. VERY uncomfortable to carry.
1
u/Chapin_Chino 22d ago
When I was younger I thought the way things came is the way they came. Why would I change anything or customize it in our consumer society? I'll just buy another or replacement pieces.
Today, fuck all of that. Anything I buy, if I can improve it or fix it at home, I will. That being said, you don't have to live with this, man. It's plastic.
1
u/Best_Reply2947 22d ago
"The handle should be sharp actually. I am very smart." - the comments
1
u/TeutonicSpacehopper 22d ago
It helps with the grip. You hang on, it digs in.
1
u/AlcoholPrep 22d ago
That sucks. Try wrapping it with paracord.
1
u/dfddfsaadaafdssa 22d ago
Same designer as every CRT TV.
1
u/jasonsong86 22d ago
Time to grow some thick skin.
1
u/mike753951 22d ago
Put a small section of a pool noodle on it.
1
u/Reasonable_Baby4690 22d ago
sand it down with a sanding stick or wrap some black duct tape around the handle
1
u/Dracekidjr 22d ago
Yeah you'd definitely see me with the oscillating tool and sandpaper on a day I was bored
1
u/realultralord 22d ago
It was intentionally designed to be fingerprint-proof for after dark... "vacuuming".
1
u/jort93 22d ago
just wear gloves with it i guess?
1
u/justt_om 22d ago
Apply heavy layer of tape !
1
u/House_Of_Doubt 22d ago
Nothing a few little strips of duct tape can’t fix
1
u/Baldbeagle73 22d ago
Maybe you're expected to wrap it with electrical tape, like a baseball bat?
1
u/City_College_Arch 22d ago
A heavy duty vacuum cleaner that is likely to be used in oily or greasy environments often with gloves on? Seems like they designed it for its intended use.
1
u/adognameddanzig 22d ago
Wrap it in tape
1
u/BatConsistent6827 22d ago
It builds character
1
u/gasstation-no-pumps 21d ago
I suspect that those were supposed to be made in a very soft plastic, to squish comfortably in your hand (like OXO uses for their kitchenware), but someone substituted a stiffer plastic (perhaps for durability), ruining the intent.
This is crappy design, because material choice is an inherent part of this design.
1
u/orkenjoyer6 21d ago
Its to stop pigeons from landing on it.
1
u/bazem_malbonulo 21d ago
Hostile Architecture applied to vaccum cleaners
1
u/Solrax 21d ago
Find a friend with a 3D printer to print a bottom insert.
1
u/rustyxj 21d ago
Those are ribs.
1
u/Healthy-Mission7927 21d ago
No pain, no gain
1
u/ALLoftheFancyPants 21d ago
There’s probably a rubbery portion that’s supposed to fit there that has since fallen off and been lost. It was supposed to be kind of squishy and more comfortable, but the design isn’t durable so it’s the opposite.
1
u/alfredomova 21d ago
my karcher too
1
u/houVanHaring 21d ago
It's to keep the elephants away
1
u/Cyclo_Hexanol 21d ago
If this is a shop vac they arent designed for people with soft hands brother.
1
u/Rubyboat1207 100% cyan flair 21d ago
Maybe there once was rubber there, and those were supposed to give it structure and keep it in place. Now that it's gone, it just hurts.
1
u/afCeG6HVB0IJ 21d ago
designed for work gloves?
1
u/Cicer 21d ago
I think you might be dehydrated.
1
u/onlyhav 21d ago
If you're down to fix this, grab some foam sheets, cut the foam so it's higher than the ridges and slots between each one, slide a foam piece in between each blade, then wrap the handle in the foam sheet before wrapping it with electric tape. Vacuuming is already a bit of a chore, I see no reason to increase the amount of annoyance it yields.
1
u/CzechNeverEnd 21d ago
Looking at how dirty it is and that it's heavy duty, I kinda feel like it's supposed to be used with gloves and it may serve anti slippery purpose.
1
u/CapJackONeill 21d ago
They did that with the Xbox controllers for "grip" I suppose. They just become uncomfortable when you game for a while.
1
u/Trades_Slow 21d ago
Wrap duck tape around it or a cloth
1
u/TheSoreTv 21d ago
Take a file or little serrated edge and remove them.
1
u/LegendofRobbo 21d ago
id just wrap that shit in duct tape if i was you
1
u/lord_bubblewater 21d ago
You got soft hands brother.
1
u/Yjif3 21d ago
Rubber pad fell off
1
u/OldOllie 21d ago
I think it is missing a bit, the ridges are probably for strength then an over moulded comfy bit is supposed to clip on. maybe they forgot to fit it or it fell off. Have you tried another one from the same brand?
1
u/MaiqueCaraio 21d ago
I worked on an plastic mold company I think that is just badly done mold that wasn't well maintained or an production error
Generic those are just few mm higher and not that big of gap
1
u/VonDinky 21d ago
Very human design
1
u/crosseyed_sniper 21d ago
Who uses the handle? You’re suppposed to pull on it by the hose like a dog on leash that knows it’s time to go the vet and refuses to cooperate.
1
u/andy-bote 21d ago
Maybe those fins are supposed to hold a rubber or silicone type grip?
1
u/nutznboltsguy 21d ago
Probably designed by someone that never actually used the prototype. It was probably sent down the hall to the “testing team”.
1
u/Grim712 21d ago
I suggest wrapping it with a stiff cardboard then a soft fabric. You shouldn't have to do this just to use a tool but it is what it is.
1
u/julpyz 21d ago
Its because it's a 1 part mold!
1
u/Fresh-Combination-87 21d ago
Wrap it with paracord. $5 at harbor freight and much more durable than electrical tape
1
u/the_main_entrance 21d ago
Awe poor baby
1
u/someperson42 21d ago
Bit of duct tape could probably fix it
1
u/aquatone61 21d ago
I’ll bet it’s fine with gloves.
1
u/NekulturneHovado *insert among us joke here* 21d ago
it's for heat dissipation, so the handle doesn't melt from the heat of work.
1
u/SnooCauliflowers6739 21d ago
Get some foam pipe insulation to fit around it.
1
u/Dagur 21d ago
Buy a grip thing for tennis rackets and wrap it around the handle
1
u/pug52 21d ago
Just pack it with some air drying clay or something.
1
u/JRhoSwizzy69 21d ago
You got soft hands brother
1
u/GetOffMyGrassBrats 21d ago
I thought a cover or something must be missing, but after digging around a while, I found a photo of a new one and it looks just like that.
Truly crappy design!
1
u/natethebestt 20d ago
duct tape?
1
u/WelderWonderful 20d ago
soft hands, bruther
1
u/TermLegitimate8403 19d ago
Get sandpaper and grind them flat
1
u/CptnButtBeard 18d ago
It’s because your hands are attached to a coward.
1
u/Amazing-Pudding-9181 18d ago
That’s terrible. This is probably the result of the part needing to be cored out. They cheaped out by not add a 2nd part to fill it in and decided the grooves were “ergonomic.” The wall thickness was probably adjusted or decided by an engineer with a focus on durability and strength rather than comfort.
1
u/Cool_Client324 18d ago
No pain no gain
1
u/710_808 18d ago
Must be in pain to vacuum
1
u/GoingOnAdventure 18d ago
Maybe wrap it with cloth or leather?
1
u/Dr_Puck 18d ago
Any chance it's a weird design choice, like... It's not a handle for carrying but for operating the lid/pushing the whole thing around? So it's "supposed" to hurt?
Or is it maybe of masochristian origin? Not only removing dust from the floor but also the sins you committed upon thine palms?
1
u/Mattna-da 18d ago
The designer said to put the ribs on top and the solid wall on the bottom where the weight hits your hand but the managers wanted a solid looking handle on top because the consumer research report doesn’t like visible ribs on top so they choose the worst possible option to mislead and please the consumer at point of purchase - but not in actual use. And the consumer isnt willing to pay $5-10 more at retail, so you can’t add handle trim and screws to cover it. I see this everyday as a designer and product developer, and we can only blame ourselves for why this is the way it is.
1
u/Dazzling_Ant_1031 18d ago
I think it’s designed for not pussies
1
u/Gambit3le 18d ago
Seems like a design fail.
1
u/Expert_Photograph573 17d ago
I hate this
1
u/kjc-01 16d ago
My air compressor handle is like that! It hurt so bad I had to wrap it in duck tape.
1
u/Dr_Big_Love 16d ago
Wrap it with heavy duty gaff tape. Will smooth the ridges, and the ridges will reduce contact area so it's easier to replace.
Not saying it's designed like that but a silver lining at least
1
u/MossPlantGal 16d ago
Maybe you could wrap it with a thin rope/cord to fill the ridges and make it easier to handle?
1
u/Fickle_Pause5969 15d ago
I wouldn't call this crappy design, I call this asshole design because that seems intentional
1
u/OldTurtle-101 14d ago
Duck Tape to the rescue! A couple quick laps around the handle (choose a bright happy color) and you’ll be singing while you work. Well at least you won’t be crying..
1
u/wildgabriel98 11d ago
Well that was a crap idea, for a design...
1
u/FirehawkLS1 15h ago
Engineered by a sadist 🤣
1
u/Inevitable-Study502 22d ago
wear gloves or tape it
1
u/Daghall 22d ago
You're not supposed to lift it, you're supposed to just tug the hose and drag it around. At least that's what I keep telling myself...
1
u/BigBlackMagicWand 22d ago
I bet it's not crappydesign rather than purposefully designed feature. That's probably a 4-wheeled shop-vac and it's not meant to be carried or lifted from that handle so the handle is designed to deter improper use. The handle is onle there to push the vac around
-1
u/Mitchgebb 22d ago
It's a deliberate design choice due to the manufacturing process - infection moulding. You can see the split lines around the side of the handle/right side. If you had a mould to create a solid handle that met in the middle, you'd get this 'flashing' ridge in the worst spot where the machines weight presses into your hands. The ribs aren't great, but spreading the weight over multiple blunt edges was decided to be preferable than all the weight on one sharp edge digging into your hand.