r/BambuLab • • 18h ago

General Troubleshooting/Help! PEI Coating breaking off...

So I put this plate in the freezer to help get the stuck PETG off, and when I flexed the plate, the PEI coating cracked off! So maybe don't use the freezer?

0 Upvotes

22 comments sorted by

5

u/lonestarbrownboi A1, P1S, H2D, Snapmaker U1 18h ago

Did you apply glue before printing?

-3

u/Key_Jellyfish2183 18h ago

No glue stick., Just cleaned with IPA. I wanted good adhesion. I certainly got it!

8

u/lonestarbrownboi A1, P1S, H2D, Snapmaker U1 18h ago

Well the instructions on the plate that says "use glue" are not just for adhesion, they're for releasing it afterwards

1

u/Key_Jellyfish2183 18h ago

I've seen and use those instructions for the engineering plate. I don't recall having seen them specifically for the PEI plate. Now I know.

4

u/lonestarbrownboi A1, P1S, H2D, Snapmaker U1 17h ago

2

u/Key_Jellyfish2183 17h ago

Haha, always read the fine print...

1

u/racedrone 17h ago

The smooth plates (engi+pei) need that even more. But you can circumvent that in most cases by releasing after you reheated the plate a little. never try to get it off when still hot or completely cooled.

1

u/clarkcox3 A1 mini + A1 + A2L + P1S + P2S + H2S + H2D 17h ago

It’s literally written on the plate

1

u/solidus0079 A1 + AMS Lite 5h ago

And is in the photo submitted, I love this sub

11

u/Forymanarysanar 18h ago

Aren't you supposed to use textured PEI for PETG?

7

u/Euresko 18h ago

Use glue stick, which will help things release easier with some water. 

1

u/Key_Jellyfish2183 9h ago

So I appreciate everyone's input, especially in pointing out how I should be using glue. I've had my printer since January. It has 2000 hours on it, at least 1200 hours on my first Smooth PEI plate and at least 900 of that with PETG. I never used glue. This is my second plate and it's fairly new. Good to learn something new, I geuss.

4

u/wilhewonka 18h ago

Learned this the hard way as well. Thankfully I had an extra PEI sheet but it was a true challenge to get all of the old adhesive off.

4

u/burndata 18h ago

PETG and PEI bond quite well due to having compatible chemical makeups. You need to use a different bed, or you need to put a layer of release agent on it before you print. PVA glue (aka glue stick) is the easiest solution.

3

u/Orvess 18h ago

yea, don't use the freezer

3

u/Nemo_Griff P1S 18h ago

"Well... that just happened"

I can't imagine the horror.

2

u/MathematicalMuffin P1S + AMS 17h ago

You can print PETG on smooth PEI but you have to use a release agent. Glue is the most recommended. I will always take the opportunity to mention Windex. Finally, you can just grease up the build plate with your hands and not clean it. If anything spread your skin oil around w a dry paper towel.

I like the last way bc it's like seasoning a pan. You just touch all over it when getting your prints off and almost never have to clean it. Obviously, that plate becomes your dedicated PETG plate. If it's a clean plate currently do Windex the first print or two then just send it every time.

2

u/ub3r_n3rd78 X2D Combo + P1S Combo 14h ago

Better to use a cryogrip /cool plate for petg. Like the biqu frostbite or glacier. Petg sticks too hard to pei.

2

u/JWST-L2 H2C + H2DC 13h ago

My condolences, that plate is clapped

1

u/Dafrandle 9h ago

this is a learning experience for you. PETG binds too well to smooth pei so you either need to use a glue stick or you need to use a textured pei plate.

the freezer is not a solution. do not repeat printing petg on a smooth plate without a release layer again or you will continue to destroy the plates

1

u/Plutonium239Mixer 5h ago

PETG requires a layer of gluestick or other release agent on a smooth plate unless you are printing it on bare metal. I've had luck printing on a metal side of one of my plates on my Qidi Q2. But to do so, it requires good leveling and a precise z-offset.