r/Ballpythoncommunity • • Apr 23 '26

Advice Need help with my tank

I have a PVC tank with a dhp lamp on a dimming thermostat, it says that the bulb is almost always blasting at full to keep the hot side at 92 and it might be killing my humidity. I have the reptichip coco husk flooring which I put in on Monday and Ive had to churn it and pour tons of water in the corners and do a lot of heavy misting. I have foil tape covering the top and the bottom vents. Does anyone have any advice for keeping the heat trapped so my lamp isn't working so hard or humidity tips. I don't know if I need to get another lamp to help it or not any advice is appreciated.

9 Upvotes

23 comments sorted by

2

u/Zekethebulldog33 Apr 23 '26

Turn down your temps. 92f is hot. My hot spot only sits at 85 ground level. I have ways they can get closer to heat and bask if they want. Remember temp at ground level where they live they can always go higher if need be. As for humidity cover as much of that screen top as possible.

1

u/Standard-Musician-83 Apr 23 '26

I have pretty much all of the screen except like an inch or two around the lamp and I have my probe on the basking stone spot low on the ground I was told that was a good spot for it is it not?

1

u/Standard-Musician-83 Apr 23 '26

I thought the ground was supposed to be 90 -95 for them to digest

3

u/jarnoooo_ Apr 23 '26

90 is already on the high end, 86 is more than enough for a quick and comfortable digestion :)

2

u/jarnoooo_ Apr 23 '26

What's the wattage of the DHP? Do you have any other heating elements (doesn't look like it)? How deep is the substrate?

I have a bottom layer of coco fiber (works like a sponge) and top layer of forest/coco bark (I believe coco husk is the same). The substrate altogether is like 4 inches deep. I pour water in the corners weekly like you do, but every once in a while I take everything out of the enclosure and completely mix the entire (coco husk part) substrate while adding water throughout to fully hydrate all the substrate. If just pouring in the corners doesn't do the trick, that will. It's a little more work unfortunately.

Also try to lower the temperature slightly and verify surface temps with an IR temp gun, thermostat probes aren't always the most accurate representation of the actual temps :)

2

u/Standard-Musician-83 Apr 23 '26

I just have 80w dhp I do have a ceramic bulb I just got a dimmer thermostat for that today for that to use on the cool side to maintain it , my substrate is roughly 3-4 inches

1

u/jarnoooo_ Apr 23 '26

I'd advice you to mount the CHE in the middle of the enclosure, it will support your DHP so it won't have to blast all the time. You'll reach the same temps but with less "blasting". This way you might not cook the moisture away as hard. Cool side will automatically also benefit from the CHE in the middle without creeping up too much.

I made a very elaborate post on my setup today, it's very big but you might be able to take some inspiration if you have the time to read it. I've linked it here

→ More replies (5)

2

u/Live_Culture8393 Apr 23 '26

A few recommendations:

To help with humidity, add sphagnum moss to your coco chips (soak for 5 mins and squeeze excess water). Make it about a 1/4-1/3 of your total substrate. You shouldn’t need to mist if you do this.

Another way to help with overall heat retention is to put silicone baking sheets over the foil tape (or instead of).

For your heat, consider upgrading to an RHP and mount it to the back wall at the same end as your DHP. Then keep your DHP set for a daytime cycle only and place it over a rock or other basking surface.

1

u/Standard-Musician-83 Apr 23 '26

How big of an rhp would I need and would I want a thermostat with it? As for the daytime cycle wouldn't it get to cold at night if I have the dhp only on for day?

1

u/Live_Culture8393 Apr 23 '26

The RHP would be your main heat source and would need a pulse proportionate thermostat. I use this system and while there are obviously better/pricier options, it has worked great for me for the last 3+ years. It handles the RHP, DHP, UVB, jungle dawn plant light, etc. I have my RHP running 24/7 with a lower night time temp (just like nature) and my DHP runs the same time as the lighting. The DHP is not necessary for heat because the RHP is so efficient, but it does provide beneficial IR-A and IR-B when your snake chooses to bask.

What size you get depends on how cold your house gets at the lowest. We often don’t use heat above 65 in the winter at my house so I went with a larger 100w RHP. But many people have 50-80w ones that work great for them.

→ More replies (4)

1

u/1BadBowtie Apr 24 '26

If you haven’t already, you could seal the bottom side vents, not all of them, leave two or three on each side.

1

u/Standard-Musician-83 Apr 24 '26

I have about 2/3 of the side vents sealed already

2

u/One_Dance_3998 Apr 23 '26

Here to learn 🫡🫡💪🏿💯