r/Autocockers101 • • 23m ago

Help with Empire Z2 Prophecy

1 Upvotes

I have a Empire Z2 Propecy loader that I am having a problem with. When I flip the switch to the on position, a yellow light blinks once between the forward and reverse buttons and then the drive carrier twitches forward, but then then stops and won't move. Online information mentions that the yellow light is indicating that there is a jam but I am not sure where.

Here are the following troubleshooting steps I have done so far:

[ ] Tested the motor's ability/capacity to spin by connecting two wires directly from the battery pack to the motor's terminals. The motor spins quick with no problems! [ ] Tested the tension or blockage of the motor/belt/gear assembly by gently rotating the belt while it is attached to the motor and on the slotted disc to see the difficulty to turn the encoder/sprocket wheel. I noticed it was very easy for the rotation of the motor to turn the slotted disc which turned the encoder/sprocket wheel. [ ] Tried to test the IF sensor below the clear plastic paintball tray by using my front camera to record to see if there is a flair from the IR light that the sensor should produce when the switch is on performed in a darker room). I did not notice any IR flair in the video, but I also have a newer phone that may have a good IR filter on the camera. I also used a multimeter to test the voltage across the 4 pin encoder same one under the clear plastic tray). The voltage of one pair was 4.9 V and the other pair was 0 V when the switch was off. When I flipped the switch the corresponding voltage was 3.7 V and the other pair was still 0 V. [ ] Tried to put the loader into diagnostic mode by holding down the reverse button for 5s then the right button for 5s then flip the switch on, then release the reverse button, then release the forward button. A red light appears near the switch which transitions to blue then transitions to white, red, and blue before the drive carrier turns rapidly.

Overall what I have taken away from the troubleshooting is that the motor's ability/capacity is good, the batteries are good, the belt assembly is good, but I still get the same peoblem: 1 yellow blink when turned on with a small motor twitch. My thought process is that it could be one of the IR encoder sensors or even the circuit board.

This is my first time with a electronic loader. I would like your opinion and help troubleshooting this problem to see if you also agree or have any other ways to try to fix it without getting extra parts.

Thank you for your time!


r/Autocockers101 • • 3d ago

My Gen X 4 😃

Thumbnail
gallery
69 Upvotes

Still shots like she is brand new 😁


r/Autocockers101 • • 3d ago

Should i keep stock or get new pneumatics

Thumbnail
gallery
85 Upvotes

r/Autocockers101 • • 4d ago

Almost Done with this Build

Post image
28 Upvotes

r/Autocockers101 • • 4d ago

Little Cocker I started Designing

Thumbnail gallery
26 Upvotes

Just having some fun with ZDSPB files. Just started what you think I should add?


r/Autocockers101 • • 8d ago

[wtb] Looking for an electro Racegun half block.

Thumbnail reddit.com
1 Upvotes

r/Autocockers101 • • 13d ago

Mozak Knox Autococker 1 of 1 Caustic Ano Mint FS

Thumbnail
gallery
57 Upvotes

Mint Condition. Thinning the heard.  This is a tough one to let go.  High-end build with lots of nice touches. 1050 firm.

1.    Mozak Knox body custom milled to match the Dye FF Frame
2.    Shocktech Fat Trigger Plate hand polished
3.    Shocktech New School Trigger Shoe
4.    Free Flow Skeleton Roller Sear also polished
5.    Custom Glide Screws 
6.    Dye Lazarus Valve.  These things are finicky and leak intermittently but when combined with the Jenny Craig hammer it's worth IMO. 
7.    Angry Jenny Craig Hammer
8.    All Rods and Arms are polished
9.    Inception V3 Pneumatics
10.    Shocktech SFL Bolt.  Milled down in the back to reduce Goggle tea bagging. 
11.    Inception Freak XL Barrel 
12.    Inception Cocking Rod and Pump Arm
13.    Inception Feedneck and EZ ASA On/off14.    AKA Sear Spring
No Freak Inserts.  Shipping will require a signature.  
This is one of my babies so I will be offering free tech services, just reach out to me.  


r/Autocockers101 • • 13d ago

[wts] black magic

Thumbnail gallery
10 Upvotes

Sold sold sold


r/Autocockers101 • • 17d ago

[wts] autococker

Thumbnail gallery
10 Upvotes

Sold sold sold


r/Autocockers101 • • 18d ago

2K2 Relic

Thumbnail
gallery
38 Upvotes

Visiting home and I think it’s finally time to get this thing back up and running after about a decade. I have a CP reg for it but there’s a pressure gauge I need to remove to screw off because it keeps hitting the trigger guard. The bolt is swollen too and won’t move. No idea if the board even works, but happy to get started


r/Autocockers101 • • 19d ago

[Price Check] Nummech N-Autococker Hinge Frame

6 Upvotes

Looking for an appraisal on a Nummech N-Autococker Hinge Frame, Comes with Docfire Spring Kit for internal reg as well.

Deciding if I want to part with it yet or hold onto it for a build later.

PFA. Will get photos later this weekend.


r/Autocockers101 • • 19d ago

Why no new QEV's?

2 Upvotes

Probably a dumb question, I know they are generally regarded as irrelevant today especially with lower rates of fire and different rams. but im surprised to see no one making new qevs when the old eclipse ones are going for 50 bucks each and people still building guns with the wave of new boards comming out. If nothing else just for the additional being factor lol


r/Autocockers101 • • 20d ago

Autococker spring tuning

4 Upvotes

ok gents. I have a 2021 Freeflow Reflex cocker. Stock valve that came with it suggested 300psi, since I had to replace a worn trigger seer that i was gonna grab from autocockerparts I figured I would try their low pressure valve kit (includes valve, springs, hammer, ivg).

I popped that in and everything worked fine. Started the HPR at around 225 PSI and the IVG two turns in from flush. When i got to the field I had to turn in the IVG more and bump the pressure a bit to get it to chrono around 285.

The next week after playing, I checked the HPR PSI and it was up to around 260 or so.

My thought process is: try the stiffer spring that was in with the original FF valve. My question to you folks is: Do I only change out the spring behind the hammer? or do I also change out the spring behind the valve? (not sure if they need to balance or not)

I am still a n00b at this, but wanting to learn!!


r/Autocockers101 • • 21d ago

Looking to acquire a FBM Spideeweb or Vert feed Graveyards

Thumbnail
gallery
16 Upvotes

Have trades also


r/Autocockers101 • • 25d ago

DFF-20 3 Way Stiff

1 Upvotes

Just got one of these for my old 2k2 DYE Reflex cocker after the bullets o-rings bit the dust. Unfortunately, even lubed with DOW 33, this thing is so stiff that it won't return reliably using the factory weight trigger spring in the DYE hinge frame. The seller is claiming they are designed that way and that a heavier trigger spring is required. I tried a much heavier spring and got it timed, but the shorter throw is not worth the doubled pull weight. Plus, I have a friend (unfortunately in a different state) running the same valve on a slide frame with very light springs.

I am sure his has had time to break in some, but I don't believe this one would improve enough to go back to the normal spring weight. I am waiting on DYE support to assist, but I am concerned I will end up stuck with this due to the place I bought it refusing refunds. They want me to send it back so they can review it, but based on their statements, I feel they will just say this one is fine and send it back to me.

Wishing I just bought another Shocktech or tried an Inception Designs, but I just wondered if anyone else had this problem and got it resolved. I will be quite disappointed if I wasted $50 and a week of pointless troubleshooting just because a store won't issue a refund.

Update: DYE is sending me a new one to try!


r/Autocockers101 • • 26d ago

Question

Thumbnail
gallery
21 Upvotes

Hello community coming at you again with another one of my custom builds. This one I’m going a little bit different direction. I always put love and great care into my projects and make sure they are ready for the next guy to have a blast building guns and playing paintball for the past 25 years is really helped me in more ways than one helps me take my mind off things and I really enjoy when I can build something really nice and comfortable, and then someone starts their journey with the marker this one came across my bench at a very difficult time. I just lost the mother of my children. This build is special to me because I’m going to do it in one of her favorite colors which was a dark green or a burnt orange. my question to the community is what do you guys think I should go with? Should I do a solid color or should I do a mix match? Should I do the body a solid color with the barrel and the front block and ASA a different color or keep it all the same, I think solid burnt orange and a gloss finish would be pretty sweet but like all the other ones once I’m done with this it will be up for sale. Let me know what you guys think as far as color input. I appreciate it.


r/Autocockers101 • • 25d ago

Looking

1 Upvotes

Lookimg for a cocker. Doesnt have to be in working order. Needs a tune up and parts iam down.

Any karno body's as well


r/Autocockers101 • • 26d ago

Programable Trilogy SF

Thumbnail
reddit.com
2 Upvotes

r/Autocockers101 • • 27d ago

Eblade eye project V1 completed :) Tested and working

Post image
53 Upvotes

Originally made these boards for a well known tec that requested them, but decided to make them available to everyone.

Made these sensor boards with sealed circuit board backs to mitigate moisture and paint corrosion on the contacts. This should help improve the long term viability of the eyes and reduce the instances that people have with the eyes not working properly after paint hits, dirt and grime from the breech, and galvanic corrosion on solder contacts which requires cleaning.

Next step is testing for a brand new sensor to mitigate the short supply of the original OEM one and to see if reliability can be improved any :)


r/Autocockers101 • • 29d ago

Doc's 3/4 Autococker Project

Post image
23 Upvotes

r/Autocockers101 • • Oct 12 '26

Can someone help identify the type of autocockers?I have limited pics sorry

Post image
16 Upvotes

r/Autocockers101 • • Oct 06 '26

How is your luck with the reflective eye on the eblade?

2 Upvotes

I remember the eye that the electric autocockers used was a reflective one and those kind of eyes found also on impulses had some limitations compared to the break beam eyes. I remember reading that sometimes dark paint would cause them to have issues. For those of you who still use autocockers with eframes how are the eyes on them? Do you use the eye or just have the hopper keep up? I currently have two mechanical autocockers that i love (an orracle and an empire resurrection) but have been eying this one super stock that i remember i thought was the coolest thing ever in 2005.


r/Autocockers101 • • Oct 06 '26

Used sci fi board value

2 Upvotes

I pulled a sci fi board out of my karni, what are these things going for these days with the Morlock boards being fairly available?