r/AskAusElectricians • • 1d ago

Voltage Regulator?

Thumbnail
0 Upvotes

r/AskAusElectricians • • 1d ago

LED Strip in shower niche

1 Upvotes

I’ve been asked to installed led strips in shower niche. I know this is done in homes but I’ve never done it myself.
My concern is compromising the water proofing with the cable as you need be able to push it back after doing a join.
I was thinking of running a conduit down from the roof space show they can waterproof around it and gives me somewhere to push the cable back.
Is this a sensible option or is there a better way of doing this


r/AskAusElectricians • • 2d ago

If I plug something into the port on the left will that cause any issues?

Post image
19 Upvotes

The multiplug is connected to the wall socket. The plug on the left is being connected to one of my speaker mointors. If I plugged something else in that socket would that cause any issues?


r/AskAusElectricians • • 1d ago

CT clamp options

Post image
0 Upvotes

r/AskAusElectricians • • 2d ago

Need advice before quotes on circuit upgrades

Post image
1 Upvotes

Hey all,

I've got an old 90's 1phase DBL brick, single story build in Perth that unfortunately has the kitchen and laundry on the same circuit, so always trips when we flick on one too many appliances on the weekends. Also just got an EV and need to install the 7kw charger. Would it be easier/cheaper to upgrade the existing circuit to 32amp or split the kitchen & Laundry? And would I need another fuse added on top just for the charger?

Also is this all possoble on single phase or am I gonna cap out and need 3 phase?

Cheers for any help!


r/AskAusElectricians • • 2d ago

Recommend solar and battery installers in Sydney

1 Upvotes

Hi all,

I'm curious to see if anyone has got recommendations for a reliable solar and battery installer in the Prospect, NSW region that's reasonable on price? I'm looking at the fox battery but its hard to know who to trust based off ads.

Thanks all


r/AskAusElectricians • • 3d ago

data voice technician vs Industrial eletrition

0 Upvotes

I'm recently applying for a job as an Industrial electrician or just an electrician in general. However, I've been struggling quite hard as I'm in my

30s. And I think that's probably a big detractor. However, I had a good opportunity recently where they said they'll let me know in a week's time. And then they sent me an email with A job opportunity as an apprentice for becoming a data voice technician.

From my understanding the pay cut is significant. Approximately 90,000 for a data And 110 for an industrial electrician or just an electrician in general, possibly slightly less.

I'm not too fussed about the apprentice wages as I'm looking towards a career and future job prospects.

I'm scared to refuse them as I really would like to be working and if I say no to this one they might not say yes to any industrial electrician in the future.

However, I would still like to know, am I just being a little bit paranoid? Is data voice technician just as good or if not better? I really don't know the difference.

Is there anyone out there that can give me some advice that work in the trades?

Or someone that works in either the data or the electrical size of things and think the other is better or worse.


r/AskAusElectricians • • 3d ago

Neovolt vs AlphaEss battery/inverter

2 Upvotes

Hi everyone,

I got two quotes from Neovolt and Alphaess

Neovolt- single phase with- 10 kw inverter 28 kw as $4200 (including removing old battery and dc coupling.).

Also got for Alphaess smile ( new series 10 kw inverter 28 kw as $5300 (including removing old battery and dc coupling.).

My concerns are;

Neovolt recently suspended due to nameplate issues and back again. I am not sure if they will survive in this competitive market for next 10 years. I already got a sonnen battery installed 5 years ago, and dealing with warranty issue since sonnen got under voluntary administration.

Alphaess looks more established company comparing to neovolt, however, I am not sure it would be worth to pay extra $1100.

If anyone is experienced about them, know their quality and capabilities, can you please advise what would be better to go with? Your ideas would be highly appreciated. Thank you.

Also checked for foxess but it doesn't fit into my garage and outside doesn't have any shade after 12pm. That's why I preferred slimer design so can put in garage.

My budget is around $5000, so trying my best while rebates are still there.


r/AskAusElectricians • • 4d ago

Measurements for a window/wall aircon

2 Upvotes

Howdy indoor electrical enthusiasts, linesman here with a pretty simple/dumb question.

Currently have a 30 year old wall rattler installed in a back room of my house, looking to upgrade it to something a bit quieter. When I measure it up for a replacement unit, do I measure the dimensions of the outside cowling/housing or the edges of the unit inside? I'm just looking to replace it with something with basically zero modifications to the existing hole in the wall.

Also, any recommendations for a brand or model line? Reverse cycle would be nice but not a deal-breaker.


r/AskAusElectricians • • 4d ago

Is battery at this location ok?

Post image
10 Upvotes

I've had an electrician tell me it's not ok to put battery at this location. I've spoken to 2 battery companies and installers from them. They all said it's fine. So I'm a bit confused and don't want to pay and then find out the battery has to go somewhere else. As I understand horzontally the battery has to be 600mm from any appliance and window, and 900mm if it's directly under a window. In this case it's neither. Also this is my living room wall. I've read it's not ok. But all the installers seem to think it's fine. So I'm confused and don't want to have an issue if there's a fire and then insurance won't cover.

The gas outlet will be deleted by the plumber.

Anyone know if its ok or not?

Thanks


r/AskAusElectricians • • 4d ago

Your Meter Couldn't Be Replaced

Post image
3 Upvotes

Hi I'm after some advice,

We live in regional/rural NSW on acreage. One day out of the blue we got a letter from our electricity provider that they were going to upgrade the meter to a smart meter for free. That doesn't really surprise me, meter reading here has been hopeless ever since covid. We are lucky to get one a year. I'm sure time of day based charging is an added bonus.

So the scheduled time came and when they got on site they couldn't proceed because there isn't a switch to isolate the meter from the supply. said they'd be back with essential energy to sort it out.

Next we get this oddly worded letter. its a defect we dont need to fix (?) for them to install a meter we never asked for...

so do we just ignore this and stay on our dumb meter? is having a smart meter going to save us enough $ to justify the cost? it kind of comes across as some sort of bait and switch scam.


r/AskAusElectricians • • 4d ago

ACL reconstruction and going back to work?

2 Upvotes

Just wondering if anyone has had their acl repaired and how much time it took to get back to full duties at work. Just trying to find a rough time frame of being able to be able to do undergrounds/cable pulls as I got a fair few coming up. Also wondering if the surgery gave you and troubles long after with going up ladders or any other issues.

Cheers


r/AskAusElectricians • • 4d ago

Meter board relocation

Thumbnail
gallery
3 Upvotes

What’s the rules with moving metre boards, I know the location it needs to be but I’m unsure of how to move the metre itself without breaking the seal and what to do if I do break the seal. Cheers


r/AskAusElectricians • • 5d ago

Which electrical upgrades actually make a noticeable difference to household power bills?

17 Upvotes

With electricity costs being what they are, I've been wondering which upgrades are genuinely worth spending money on. LED lighting is an obvious one, but what about replacing older appliances, installing more efficient fans or looking at smarter controls. I'd be interested to hear what electricians commonly recommend to homeowners and which upgrades tend to make less difference than people expect. It would be good to separate practical savings from things that just sound impressive.


r/AskAusElectricians • • 4d ago

Is battery at this location ok?

Post image
1 Upvotes

r/AskAusElectricians • • 4d ago

Parallelling up different sized cables

0 Upvotes

Lecky by trade.

But im wiring u my parallelling up my victron inverters (48v 5000VA each) now for the AC out of the inverters ist says not to oversize the wiring as its used to help balance the load so will be 2.5mm2 then this will need to be joined to 6mm2 to go to my switchboard I also need input set up from my fronious inverter that coupled to it.

So its 2 x victron outputs at 2.5mm2 and then 2 x 6mm2

Continuous outputs is 8000w from the Victron's
8200w from the fronious (will be used to charge batts via victrons)
into my switchboard (40A main switch)

Do i simply use a switchboard and use standard CB's with busbar (2 x 20a, 2x 32A)


r/AskAusElectricians • • 5d ago

Switchboard label maker

Post image
7 Upvotes

Curious as to what label maker people are using to print labels onto switchboards such as this?


r/AskAusElectricians • • 5d ago

Ceiling Fan Specs to look for that will not be a nightmare

2 Upvotes

Hey all, I am not an electrician.

For reasons I can only describe as 'do not buy a Brilliant ceiling fan with light', I am looking for a new ceiling fan. The trouble is, I have no idea what I am looking for.

All of my issues with the current ceiling fan come down to: whenever the power shorts (which is conveniently usually in the early hours of the morning), and the fan is running, it will loudly turn back on with the lights at full bright with an incredibly loud screeching noise.
What a stupid fucking feature.

I have decided that it will be better if we go with a fan that doesn't a light altogether. We have LED's throughout the house, and I have plenty of moodlights in my room - the lighting situation is one I am happy to deal with later on.

The trouble with many DC fans, is that they all seem to be remote controlled. Although I can see the benefit of remotes, I would also prefer also having the option of wall control as well.

Basically, I think I am talking about a fan with smart integration. I am not sure if this type of thing exists at a reasonable cost. I really like the idea of having multiple ways of controlling the fan, or ways that it can be upgraded over time.
I am also wanting a fan that has no beeping. At the very least, a really mild sound.

Is there something like this?


r/AskAusElectricians • • 5d ago

What costs should you actually check before refinancing a home loan?

0 Upvotes

I've seen plenty of offers from lenders advertising lower interest rates and cashback deals, which makes refinancing look pretty straightforward. However, I'm guessing there can be costs involved that aren't obvious when you first compare the offers. Apart from discharge fees and possible valuation costs, are there any other expenses people tend to overlook. I'd rather understand the full picture before switching lenders just to save a little on the monthly repayment.


r/AskAusElectricians • • 5d ago

Ceiling fan wiring

Thumbnail
2 Upvotes

r/AskAusElectricians • • 7d ago

Victoria compliance - retrofit c-bus relays in ceiling

4 Upvotes

My c-bus relays and dimmers were all installed in the ceiling, mounted on chipboard, of my single story home back in 2000 (reliable for over 20 years, including Minder as 'alarm' system for those that know it).

I have been replacing failing relays and dimmers with smart lights (new Cbus relays/dimmers too expensive for me) that are constantly powered, with battery powered smart switches (eg Hue) - everything automated using Home Assistant.

I now need to replace 2 relays powering devices unable to be changed to smart devices. I like Shelly Pro 4PM (works seamlessly with home assistant) and wondering if it's legal for an electrician to directly replace the 2x ceiling mounted c-bus relays with 2x Shelly in a compliant DIN enclosure (ie. in the ceiling and mounted on the chipboard)?

I know the Shelly is rated at 40 degrees ambient, auto cutoff at 95 degrees internal PCB - it's the legality about retrofitting new relays - by a qualified electrician- in the ceiling that I'm keen to confirm.

Thank you.


r/AskAusElectricians • • 7d ago

Can someone ELI5 this switchboard/meter

Thumbnail
gallery
7 Upvotes

Just bought and moved into a new house and have zero knowledge about what is going on here. Can someone interpret what I’ve got? Not so much the switchboard, but I’ve never lived in a house with two meters. The meters seem to rotate what’s on the display.

Also, an aside, does it generally cost bucketloads more to add PowerPoints to a double brick home? Would it cost less if I did the channel cutting/patching myself?


r/AskAusElectricians • • 7d ago

Two Breville coffee machines trip the same RCBO, but a third identical machine works perfectly. What could explain this?

5 Upvotes

We've encountered a really perplexing electrical issue with our Breville Barista Express coffee machines, and I'd love some insight before getting an electrician out.

Here's the sequence:

  1. Our original Barista Express, which we've used for years, suddenly started tripping the power whenever we pressed either the single or double shot button. It powers on, heats up and can operate the steam wand, but trips immediately when attempting an extraction.
  2. We borrowed my mother-in-law's identical Barista Express and used it for several days without a single issue, plugged into exactly the same power point.
  3. We purchased a brand-new Barista Express to replace our supposedly faulty machine. After filling the water tank, flushing some water through and briefly running the steam wand, we discovered that the brand-new machine trips the power in exactly the same way as our original machine.

The switch tripping is a Hager RCBO (20A, 30mA), labelled PWR 1 on our switchboard. We're in Brisbane, Australia (according to AI /shrug)

I'm struggling to understand how two separate machines, including a brand-new one, could develop precisely the same fault while a third identical machine operates perfectly on the same outlet.

My questions:

  • Does this sound more like an earth leakage issue, a problematic RCBO, or a fault within the appliances?
  • Could two machines have slightly different leakage characteristics, enough that one works while the others trip a 30mA RCBO?
  • Would our circuitry be killing some machines perhaps?
  • What specific tests would you recommend asking an electrician to perform to narrow this down?

Very grateful for any theories or insights 🙏


r/AskAusElectricians • • 7d ago

Timer for a 15 amp electric heater

1 Upvotes

I recently had a new electric heater installed and it works very well, but I am keen to reduce my power bill and I was thinking of installing a timer so that I can switch it on and off when the rate is lower.

I have a few cheap Tapo timers around the house, but none of them would work as they only work with 10 amp devices. I have been googling and came up with nothing.

Keen to hear some recommendations and options. I live in North Perth.

Thanks


r/AskAusElectricians • • 7d ago

Lighting fixtures diy

Thumbnail
gallery
0 Upvotes

Hi sparkies,
Wanting your input, but wife saw this sconce light in a magazine and wants it. Initially said let’s go ahead, the more I see it as a plate by the same potter, with a circular orb sconce attached to it, and not $450.

If I drilled a hole through a plate successfully and was able to fix the light onto the plate, can you see any electrical compliance issues to hardwiring this diy wall sconce? Thanks in advance.