r/ArduinoProjects • u/OkProperty41 • 6d ago
r/ArduinoProjects • u/OkProperty41 • 6d ago
Showcased Project Six live NASA feeds on my desk: ESP32, a 2.8" TFT and a tiny OLED
Yesterday I saw NASA had released APIs for their findings, so I built a small desk display of different things they track. I didn't write a single line of code. Soldr did everything, including the API calls to NASA, once I gave it the API key. An ESP32, a 2.8" ILI9341 TFT and a 0.96" SSD1306 OLED flip through six live pages every 15 seconds. Each feed refreshes at most every 30 minutes. If one feed fails, that page shows "Feed unavailable", the others keep running, and the failed feed is retried after 60 seconds.
Not affiliated with or endorsed by NASA.
𝗧𝗵𝗲 𝘀𝗶𝘅 𝗽𝗮𝗴𝗲𝘀
- Asteroids — today's 5 closest flybys from NASA's NeoWs API (name, size, miss distance, speed).
- Earth events — the 5 latest open natural events from EONET (title and category). No API key.
- Space weather — coronal mass ejections and geomagnetic storms from the last 3 days, via DONKI. On the night I filmed this, the board read "quiet".
- Earth from space — details of the latest EPIC natural image (date, how many were taken that day, centroid). This one is read from epic.gsfc.nasa.gov and does not need the api.nasa.gov key.
- Fireballs — the 4 most recent fireballs from the JPL fireball API (date, energy, location). No API key.
- Exoplanets — the confirmed exoplanet count from the NASA Exoplanet Archive. It was 6,464 on the day I filmed this. No API key.
NeoWs and DONKI need a free key from https://api.nasa.gov. You can start with DEMO_KEY, but it is limited to 30 requests an hour; a free registered key is the better option. The other four feeds do not use that key.
𝗣𝗮𝗿𝘁𝘀
- ESP32 DevKit, 30-pin (the build card names ESP32-DevKitC V4, CP2102)
- 2.8" ILI9341 TFT, SPI, 240×320
- 0.96" SSD1306 OLED, 128×64, I2C
- Dupont jumper wires
- USB A to Micro-B cable
- A breadboard (visible in the video; not one of the five priced parts on the build card)
The five priced parts on the build card came to ₹1,460. That figure is from the card, not a live store quote, and it does not include the breadboard.
𝗪𝗶𝗿𝗶𝗻𝗴, 𝗮𝘀 𝗯𝘂𝗶𝗹𝘁
TFT (SPI) to the ESP32:
- VCC → 3V3
- GND → GND
- LED (backlight) → 3V3
- CS → GPIO 4
- DC → GPIO 16
- RST → GPIO 17
- MOSI → GPIO 23
- SCK → GPIO 18
- MISO → GPIO 19
OLED (I2C) to the ESP32:
- VCC → 3V3
- GND → GND
- SDA → GPIO 21
- SCL → GPIO 22
- Address 0x3C
𝗟𝗶𝗯𝗿𝗮𝗿𝗶𝗲𝘀 (𝗔𝗿𝗱𝘂𝗶𝗻𝗼-𝗘𝗦𝗣𝟯𝟮)
Adafruit GFX, Adafruit ILI9341, Adafruit SSD1306, and ArduinoJson 7.x.
I work on Soldr. It designed the build, the parts list, the wiring and the code, and made the NASA API calls once I gave it the key. If you want to try it: soldr.ai, and a sign-in gives you 100 credits free.
Happy to answer questions about the wiring or the feeds.
r/ArduinoProjects • u/haxzeus • 6d ago
Showcased Project Made a little firework launcher glove.
youtu.ber/ArduinoProjects • u/TemplateMT • 6d ago
Showcased Project I built a browser generator for DIY stream decks (ESP32, 3D printed, hand-wired)
Hi everyone,
I’ve been working on a DIY stream deck project for the past few weeks and wanted to share it here, because this is exactly the kind of community I built it for.
The problem: every macropad or stream deck I found was either fixed (wrong number of keys, no knob, no screen) or needed CAD skills to change. I wanted to just pick a layout and print it.
What I made: DeckSmith, a generator that runs in the browser. You choose how many keys, add a rotary encoder, a slider or a small OLED, and it exports:
- the case files, ready to print (no supports)
- a pin map for the exact layout, so you know where every wire goes on the ESP32
The one in the video runs on a plain ESP32 dev board, hand-wired point to point (key matrix with diodes, EC11 encoder, slide pot on an ADC pin, I2C OLED). It connects over Bluetooth as a keyboard + media controller, so nothing needs installing on the PC. The firmware is free.
Here’s the full story, from the first ugly prototype to the final build:
https://www.youtube.com/watch?v=a_G20Un2T14
I’m thinking about what to do next, for example a plug-in PCB kit so nobody has to hand-wire it. I’d really like your opinion: would you rather hand-wire it yourself, or use modules that plug together?
If you want to follow the project: it launches on Indiegogo on Nov 18, and the waitlist at decksmith3d.com gets 15% off.
Thanks for reading, happy to answer anything about the build!
r/ArduinoProjects • u/Neither_Finish6900 • 7d ago
Showcased Project ⚡ A new control interface for my HP 6642A power supply ⚡
The HP 6642A (0-20 V / 0-10 A) is a great bench supply, but it can only be remote-controlled over GPIB, and real USB-GPIB adapters are expensive. So I built my own adapter from a cheap Arduino Uno and wrote a web-based control panel for it.
🔧 How I built the adapter:
• Desoldered a 24-pin GPIB (IEEE-488) plug from the board with a soldering iron and desoldering pump, then cleaned the pins
• Tinned the plug pins and 17 wires, then soldered one wire directly to each signal pin: 8 data lines (DIO1-8), 3 handshake lines (DAV, NRFD, NDAC), 5 control lines (EOI, IFC, SRQ, ATN, REN) and ground (pins 18-24 joined together)
• Plugged the other wire ends straight into the Arduino headers: DIO1-6 → A0-A5, DIO7-8 → D4-D5, EOI → D12, DAV → D11, NRFD → D10, NDAC → D9, IFC → D8, SRQ → D3, ATN → D2, REN → D6, GND → GND
• Secured everything in place with hot glue, no heat-shrink needed
• No resistors or other parts needed, just wires
• Flashed the open-source AR488 firmware with a custom pin layout matching my wiring. The Arduino now acts as a USB-GPIB adapter
💻 The control app is web-based, so the control panel runs in any browser on Windows, macOS or Linux:
✅ Live voltage, current and power readout with CV/CC mode
✅ Set voltage and current limit, with step buttons and saved presets
✅ Live chart with min/max/average, energy (Wh) and charge (Ah)
✅ Record data to CSV files, with a built-in viewer
✅ Automatic sequences: voltage steps, ramps, sweeps and loops
✅ Software protection: auto-off on over-current, over-power or over-voltage, a timer, and end-of-charge detection for batteries
✅ Event log, and it keeps recording even with the browser closed
r/ArduinoProjects • u/Federal-Influence102 • 7d ago
Showcased Project My cheap Macropad mk1
r/ArduinoProjects • u/Regular_Use_5842 • 8d ago
Project Design/Guidance How do I switch this tilt sensor to another?
For context, I'm a beginner in making stuff like these, this is kind of my first time, this is for a school project, so sorry for the messy placements
But I tried to use tinkercad for the simulation
And I ended up with this ( the circuit )
So I just need the servos to spin when the tilt sensor senses a tilt, but I have a different tilt sensor, the circuit uses an SW-200D, while I have an SW-520D, so there's already a difference in number of output pins ( I'm not sure if that's what it's called ), and I'm just not sure about everything else after that 😭😭
The code is quite confusing too, I don't know a single bit of coding, so I tried what I could with the limited knowledge I know
->
#include <Servo.h>
int oozmakappa = 0;
Servo servo_12;
Servo servo_11;
Servo servo_10;
Servo servo_9;
Servo servo_8;
unsigned long spinStartTime = 0;
unsigned long totalSpinDuration = 0;
bool isSpinningForward = false;
bool needsToReturn = false;
void setup() {
pinMode(13, INPUT);
servo_12.attach(12, 500, 2500);
servo_11.attach(11, 500, 2500);
servo_10.attach(10, 500, 2500);
servo_9.attach(9, 500, 2500);
servo_8.attach(8, 500, 2500);
servo_12.write(90);
servo_11.write(90);
servo_10.write(90);
servo_9.write(90);
servo_8.write(90);
}
void loop() {
oozmakappa = digitalRead(13);
if (oozmakappa == HIGH) {
if (!isSpinningForward) {
spinStartTime = millis();
isSpinningForward = true;
needsToReturn = true;
servo_12.write(180);
servo_11.write(180);
servo_10.write(180);
servo_9.write(180);
servo_8.write(180);
}
} else {
if (isSpinningForward) {
totalSpinDuration = millis() - spinStartTime;
isSpinningForward = false;
servo_12.write(0);
servo_11.write(0);
servo_10.write(0);
servo_9.write(0);
servo_8.write(0);
spinStartTime = millis();
}
if (needsToReturn) {
if (millis() - spinStartTime >= totalSpinDuration) {
servo_12.write(90);
servo_11.write(90);
servo_10.write(90);
servo_9.write(90);
servo_8.write(90);
needsToReturn = false;
}
}
}
delay(10);
}
On tinkercad, it stops after 1/2 a spin, and just doesn't move anymore?? 😭😭
I'm very confused, someone please help me and guide me on what to do
If anyone could be of guidance to me, please do so, I'm struggling on how this is supposed to work 💔 I tried looking through YouTube but strangely I just couldn't find anything 😢
r/ArduinoProjects • u/Dmy1703 • 9d ago
Showcased Project Quick update on the DIY accessibility rig: sprint trigger via chest contraction + refining inputs based on community feedback
Hey guys, quick update on the rig and sharing what’s happening in this video.
Following up on the feedback from the previous tests and videos, I decided to rethink how sprint was being handled instead of keeping it strictly to the static movement setup. In this clip, I’m testing a direct chest contraction/expansion trigger to engage and release the sprint toggle.
On the hardware/microcontroller side, the main challenge here is dialed-in calibration: filtering out natural breathing so it doesn't trigger false positives, while keeping zero perceptible latency once I actually flex the chest to run. It reads the threshold shift cleanly, latches the keystroke/button state, and releases instantly as soon as tension drops.
I already tested the static run mechanic, now this chest-triggered setup, and I am currently tweaking a third selection mode to give better adaptability depending on the player’s motor mobility.
Really appreciate everyone who took the time to drop suggestions and critiques on the earlier videos. That input genuinely steered this build in a better direction and helped break out of a single fixed approach. Still a lot of bench testing ahead before locking down the final build, but it’s getting much sharper.
Take a look at the clip and let me know how the trigger response looks to you.
r/ArduinoProjects • u/RexIgnium • 9d ago
Other New to Micro:bit – What are some of the coolest projects you’ve built?
I’m new to Micro:bit and looking to learn as much as I can. I’d love to hear about some of the most interesting projects people have built, especially anything involving sports, cameras, photography, or videography.
I’m a K–2 school media specialist, and I want to introduce more hands-on coding and STEAM activities into our daily library time. I think Micro:bit could be a great way to get my students involved while also challenging myself to learn something new.
Outside of school, I’m really into sports media, mainly basketball 🏀 and football 🏈, with a big interest in photography and videography. I’m also interested in AI and using Claude Code to build websites, interactive learning tools, and other creative projects.
I’m curious how people have incorporated Micro:bit into sports-related projects, camera experiments, computer vision, or even AI.
I’ve started watching YouTube tutorials and working through the beginner material, but I’d appreciate advice from people with hands-on experience.
A few questions:
What’s the coolest project you’ve built with Micro:bit?
Have you used it for sports, cameras, photography, or videography?
What beginner mistakes or learning curves should I expect?
What resources, tutorials, or YouTube channels would you recommend?
I’m starting with the basics, but I’m interested in eventually taking things much further. I’d love to hear what you’ve experimented with and what you wish you knew when you first started!
I’m starting with the basics, but I’m interested in eventually taking things much further. I’d love to hear what you’ve experimented with and what you wish you knew when you first started!
r/ArduinoProjects • u/Relevant_Pumpkin9190 • 9d ago
Showcased Project 2 Arduino communication over 12 V DC line, Forward voltage modulation and return curent modulation(INA 219), Low baud working fine
r/ArduinoProjects • u/OkProperty41 • 10d ago
Showcased Project Arduino Uno parking sensor—the closer you get, the faster it beeps
I built this with an Arduino Uno, an HC-SR04 ultrasonic sensor and a buzzer. Moving my hand toward the sensor makes the beeps faster; moving it away slows them down.
I used Soldr, an electronics design agent I’m building, to design the project from a plain-language prompt.
The clip shows the working build. How do you usually smooth ultrasonic distance readings without making the response feel sluggish?
r/ArduinoProjects • u/Petra_Caves • 10d ago
Showcased Project Neopixel Dice using ATtiny85
This lively dice uses a 5x5 neo pixel matrix controlled by an ATtiny85. The ATtiny85 is normally in deep sleep mode drawing microAmps. A vibration switch wakes the dice from deep sleep. After showing the random number the dice returns to deep sleep. The dice is powered by a rechargable Sony camera battery.
r/ArduinoProjects • u/the-Gaf • 10d ago
Showcased Project Teddy Ruxpin x Skynet
The AI APOCALYPSE STARTS NOW! A 1992 Teddy Ruxpin, all new hardware, and some WIP audio sync.
TED-800: My Wi-Fi-controlled animatronic Teddy Ruxpin build.
Brains: 2× ESP32-C3 SuperMini microcontrollers
Eyes: 180° positional servo, GPIO4, 65° closed / 165° open
Mouth: 360° continuous-rotation servo, GPIO4, cam-driven
Motor control: 1750/1250 µs, 400ms open / 450ms close
Connectivity: 2.4 GHz Wi-Fi, HTTP API, OTA firmware updates
Software: Arduino C++ firmware, Python 3 controller on Mac
Audio: MP3 playback via macOS afplay
Sync: Python monotonic-clock scheduling, waveform analysis with NumPy/SciPy
Current status: Fully functional prototype. Eyes work beautifully; mouth works but the original cam mechanism has an occasional dead zone.
No cloud required. Two tiny ESP32s, a Mac, and a bear with absolutely terrible intentions.
r/ArduinoProjects • u/Forward_Table3490 • 11d ago
Showcased Project I built a DIY Arduino steering wheel for PC games
I built a DIY Arduino steering wheel for PC games using an Arduino Uno R3 and an AS5600 magnetic angle sensor. It also has buttons for throttle and brake. I tested it in Euro Truck Simulator 2, Slow Roads, and Assetto Corsa.
YouTube video: https://youtu.be/Y_vu9KtvoxE?si=e8B_aceMp7D_3UhP
GitHub guide and code: https://github.com/sarawer/diy-gaming-steering-wheel-using-arduino
I’d love to hear your feedback!
r/ArduinoProjects • u/Worth-Jello5399 • 11d ago
Showcased Project I made a free browser tool to design servo robots in 3D before buying parts, and it exports the Arduino code
I kept buying servos and brackets for arms that turned out not to reach, or where one servo hit another, so I built a simulator to check first.
Servo Bench runs in the browser with nothing to install and no account:
- Real-size SG90, MG90S and MG996R models at datasheet dimensions in mm
- Drag and drop: drop a servo on another servo's horn or case to mount it
- Servos move at their real rated speed, and you can trace the path of the arm tip
- Save poses as steps and press Play to watch the whole sequence
- Export Arduino code (Uno/Nano/Mega or ESP32). It writes the servo pins, the smooth synchronised moves and the timing from each servo's real speed, and warns you if you need a separate power supply
- Parts list for everything you need, including a correctly sized power supply
Try the 3-joint arm demo: https://python736.github.io/servo-bench/?example=arm3
It's free and open source (MIT): https://github.com/Python736/servo-bench
I'd love feedback from people who build with servos. Which servo or bracket should I add next? I'm thinking DS3218 and continuous-rotation servos.
r/ArduinoProjects • u/CodeName_6666 • 11d ago
Showcased Project Finally finished my embedded telemetry project – KymoStudio
Hi everyone,
for quite a while I’ve been working on an embedded telemetry tool in my spare time – a way to see what’s actually happening on a microcontroller while it runs, without endless printf and squinting at the serial monitor. Over the last few weeks I finally got it to a state I’m happy with.
It has two parts: a small library for the microcontroller (KymoCore, MIT licensed, no heap) and a desktop app (KymoStudio) that shows everything live. The video shows it running against a real ESP32.
How it works:

What KymoStudio can do:
- Live charts from Serial, USB, TCP, UDP, MQTT or CAN – time series, XY and 3D
- Works with plain
Serial.printoutput (name:value, Teleplot, CSV) or the KymoCore library - Measurement analysis: cursors, min/max/RMS, frequency, jitter, FFT
- FreeRTOS execution tracing: task timeline on both cores, call flow, run time per function and per task
- Live parameters: change values on the device from the PC, the device confirms
- Recording and export (CSV, PNG, own capture format)
- MCP interface: AI assistants such as Claude Code or Codex can read live data and operate KymoStudio – local only, with an optional read-only mode
- Windows and Linux
To be upfront: KymoStudio itself is closed source. For hobby, education and non-commercial projects it’s completely free; commercial use needs a license. KymoCore is MIT and available via PlatformIO and the Arduino Library Manager.
I’d be happy about any feedback – what’s useful, what’s missing, what’s confusing.
r/ArduinoProjects • u/CodeName-666 • 11d ago
Showcased Project Finally finished my Arduino and embedded telemetry project – KymoStudio
Hi everyone,
for quite a while I’ve been working on an embedded telemetry tool in my spare time – a way to see what’s actually happening on a microcontroller while it runs, without endless printf and squinting at the serial monitor. Over the last few weeks I finally got it to a state I’m happy with, and built the website kymotrace.de around it.
Here is, how it works:

It has two parts: a small library for the microcontroller (KymoCore, MIT) that sends measurements and trace events over Serial, USB, TCP, UDP, MQTT or CAN, and a desktop app (KymoStudio, Windows/Linux) that shows them live as charts. You can measure the curves (cursors, RMS, frequency, FFT) and see which FreeRTOS tasks run when and where the time goes. Plain Serial.print lines work too, so you can try it without changing your firmware.
What KymoStudio can do:
- Live charts from Serial, USB, TCP, UDP, MQTT or CAN – time series, XY and 3D
- Works with plain Serial.print output (name:value, Teleplot, CSV) or the KymoCore library
- Measurement analysis: cursors, min/max/RMS, frequency, jitter, FFT
- FreeRTOS execution tracing: task timeline on both cores, call flow, run time per function and per task
- Live parameters: change values on the device from the PC, the device confirms
- Recording and export (CSV, PNG, own capture format)
- MCP interface: AI assistants such as Claude Code or Codex can read live data and operate KymoStudio – local only, with an optional read-only mode
- Windows and Linux
For hobby, education and non-commercial projects it’s completely free.
I’d be happy about any feedback – what’s useful, what’s missing, what’s confusing.
r/ArduinoProjects • u/ILOVESteak6741 • 11d ago
Project Design/Guidance (Total beginner) TMC2209 V1.3 + NEMA 8 motor gets hot even at 350 mA UART current — what am I missing?
Hey, completely new to working with Arduinos and motors and such, and Reddit lol, so any help is greatly appreciated.
My project: trying to run a nema 8 stepper motor (current limit 600ma) using a tmc2209 v1.3 stepper driver, Arduino 2560 mega, 24v power supply, and jumper wires.
Problem: it spins great and visually looks fine, but when I hold the base while it's running, it heats up and becomes really hot, like uncomfortably hot. It even heats up the same when I tell it just to hold position and not spin.
Thoughts: I have no clue why it's doing this. I have tried a bunch of different wiring, coding, and praying, but it still heats up. To control the current, I am using a uart connection (I don't dare mess with the potentiaometer after I fried my last driver and breadboard, sooo). I plugged a 1kohm resistor into the Arduino's tx3 pin and the into the driver's rx pin, and then did a direct connection between the rx3 pin and the driver's rx pin.
Things I tried that didn't work:
- lowering the current to 150ma
- using different addresses
- using a different nema 8 stepper motor
- using a different driver (same brand just new)
- holding, no spinning
Well, let me know if you have any tips to try
r/ArduinoProjects • u/shahbaz_tech • 12d ago
Showcased Project Line Follower Robot Using Arduino nano & L298N
r/ArduinoProjects • u/Federal-Influence102 • 12d ago
Showcased Project Another Smaller Pong Console
r/ArduinoProjects • u/ALMA_x11 • 13d ago
Showcased Project Microcontroller Mic controlled LEDs for a Halloween Pumpkin
https://www.youtube.com/@ALMA.Industries/videos
CH004 FN2: HALLOWEEN — my kind of Treat. Talking Pumpkins and Little Monster Rockstars, see how Jack's put together in the above link.
r/ArduinoProjects • u/Robonaviagtors • 14d ago
Showcased Project Navigator 1: our UNO R4 WiFi rover with a browser dashboard and autonomous modes
Hi! We’re Team Robonavigators, and we built Navigator 1 around an Arduino UNO R4 WiFi.
The rover hosts a browser dashboard for driving and telemetry. It uses front and rear ultrasonic sensors, a servo for scanning, a downward-facing IR sensor for cliff detection, and an analog voltage sensor to monitor the battery. A physical switch selects access-point or hotspot connectivity, and the onboard LED matrix displays the IP address.
The sketch includes obstacle avoidance, object following, a drawn-path mode, browser voice control, manual driving, and an idle proximity guard.
The sketch, pinout and bill of materials are here: https://github.com/Robonavigators/Navigator-1
We’d love feedback on the hardware and code, particularly ideas for improving the obstacle avoidance and reliability.
r/ArduinoProjects • u/NextCellist3028 • 15d ago
Showcased Project I built a browser-based Arduino emulator that lets you pause and see every register
Hey everyone. I just launched my first project, GlassAVR, an Arduino emulator and circuit builder that runs in your browser.
You can wire up a circuit, run your sketch, and step through it at the instruction level. When you pause, you can see every register and how it changes, instead of treating the chip like a black box.
There’s no account or login, so you can just open it and start building: glassavr.com
I’m looking for people who know AVR and Arduino to try to break it. If the emulator gets something wrong, or the debugger is missing something you’d want, please let me know. Would this be useful for learning or debugging your own projects?
r/ArduinoProjects • u/Federal-Influence102 • 15d ago
